U-Boot 1.1.4 (Aug 31 2008 - 22:32:16)


DRAM:  64 MB

NAND:128 MiB

*** Warning - bad CRC or NAND, using default environment


In:    serial

Out:   serial

Err:   serial

Hit any key to stop autoboot:  1  0 

NAND logical - offset 006F8000 not found

## Booting image at a0800000 ...

   Image Name:   Linux-kexecboot-2.6.26-r3

   Image Type:   ARM Linux Kernel Image (gzip compressed)

   Data Size:    1395080 Bytes =  1.3 MB

   Load Address: a0008000

   Entry Point:  a0008000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK


Starting kernel ...


Uncompressing Linux......................................................................................... done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Sun Aug 31 00:23:34 CEST 2008
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Memory clock: 99.53MHz (*27)
Run Mode clock: 199.07MHz (*2)
Turbo Mode clock: 398.13MHz (*2.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=tty1 console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61988KB available (2384K code, 236K data, 260K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY)   2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
3 cmdlinepart partitions found on MTD device sharpsl-nand
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "smf"
0x00700000-0x06700000 : "root"
0x06700000-0x08000000 : "home"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
Freeing init memory: 260K
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB 
 mmcblk0: p1
Probing /dev/mtdblock0
Probing /dev/mtdblock1
Probing /dev/mtdblock2
found /dev/mtdblock2 (jffs2)
mount successful
found kernel
found command line
Probing /dev/mtdblock3
Probing /dev/mmcblk0
/dev/mmcblk0: No such file or directory
Probing /dev/mmcblk0p1
found /dev/mmcblk0p1 (ext2)
mount successful
found kernel
found command line
No kernel specified
kexec 1.101 released 15 February 2005
Usage: kexec [OPTION]... [kernel]
Directly reboot into a new kernel

 -h, --help           Print this help.
 -v, --version        Print the version of kexec.
 -f, --force          Force an immediate kexec, don't call shutdown.
 -x, --no-ifdown      Don't bring down network interfaces.
                      (if used, must be last option specified)
 -l, --load           Load the new kernel into the current kernel.
 -p, --load-panic     Load the new kernel for use on panic.
 -u, --unload         Unload the current kexec target kernel.
 -e, --exec           Execute a currently loaded kernel.
 -t, --type=TYPE      Specify the new kernel is of this type.
     --mem-min=<addr> Specify the lowest memory addres to load code into.
     --mem-max=<addr> Specify the highest memory addres to load code into.

Supported kernel file types and options: 
zImage
     --command-line=STRING Set the kernel command line to STRING.
     --append=STRING       Set the kernel command line to STRING.
     --initrd=FILE         Use FILE as the kernel's initial ramdisk.
     --ramdisk=FILE        Use FILE as the kernel's initial ramdisk.
Architecture options: 

kexec failed: Invalid argument



U-Boot 1.1.4 (Aug 31 2008 - 22:32:16)


DRAM:  64 MB

NAND:128 MiB

*** Warning - bad CRC or NAND, using default environment


In:    serial

Out:   serial

Err:   serial

Hit any key to stop autoboot:  1  0 

NAND logical - offset 006F8000 not found

## Booting image at a0800000 ...

   Image Name:   Linux-kexecboot-2.6.26-r3

   Image Type:   ARM Linux Kernel Image (gzip compressed)

   Data Size:    1395080 Bytes =  1.3 MB

   Load Address: a0008000

   Entry Point:  a0008000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK


Starting kernel ...


Uncompressing Linux......................................................................................... done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Sun Aug 31 00:23:34 CEST 2008
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Memory clock: 99.53MHz (*27)
Run Mode clock: 199.07MHz (*2)
Turbo Mode clock: 398.13MHz (*2.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=tty1 console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61988KB available (2384K code, 236K data, 260K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY)   2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
3 cmdlinepart partitions found on MTD device sharpsl-nand
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "smf"
0x00700000-0x06700000 : "root"
0x06700000-0x08000000 : "home"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
Freeing init memory: 260K
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB 
 mmcblk0: p1



U-Boot 1.1.4 (Aug 31 2008 - 22:32:16)


DRAM:  64 MB

NAND:128 MiB

*** Warning - bad CRC or NAND, using default environment


In:    serial

Out:   serial

Err:   serial

Hit any key to stop autoboot:  1  0 

NAND logical - offset 006F8000 not found

## Booting image at a0800000 ...

   Image Name:   Linux-kexecboot-2.6.26-r3

   Image Type:   ARM Linux Kernel Image (gzip compressed)

   Data Size:    1395080 Bytes =  1.3 MB

   Load Address: a0008000

   Entry Point:  a0008000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK


Starting kernel ...


Uncompressing Linux......................................................................................... done, booting the kernel.
Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Sun Aug 31 00:23:34 CEST 2008
CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f
Machine: SHARP Husky
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Memory policy: ECC disabled, Data cache writeback
Memory clock: 99.53MHz (*27)
Run Mode clock: 199.07MHz (*2)
Turbo Mode clock: 398.13MHz (*2.0, active)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=tty1 console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [tty1] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61988KB available (2384K code, 236K data, 260K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 624 bytes
NET: Registered protocol family 16
Sharp Scoop Device found at 0x10800000 -> 0xc4806000
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
PXA CPU frequency change support initialized
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) (SUMMARY)   2001-2006 Red Hat, Inc.
msgmni has been set to 121
io scheduler noop registered
io scheduler anticipatory registered (default)
Corgi Backlight Driver Initialized.
Found w100 at 0x08000000.
Console: switching to colour frame buffer device 80x30
fb0: w100fb frame buffer device
pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART
console [ttyS0] enabled
pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART
pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART
pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
Sharp SL series flash device: 800000 at 0
Using static partition definition
Creating 1 MTD partitions on "sharpsl-flash":
0x00120000-0x007f0000 : "Boot PROM Filesystem"
NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 32 at 0x00080000
Bad eraseblock 1440 at 0x01680000
3 cmdlinepart partitions found on MTD device sharpsl-nand
Creating 3 MTD partitions on "sharpsl-nand":
0x00000000-0x00700000 : "smf"
0x00700000-0x06700000 : "root"
0x06700000-0x08000000 : "home"
pxa2xx_udc: version 30-June-2007
input: Corgi Keyboard as /class/input/input0
sharpsl_rc_init
input: Corgi Touchscreen as /class/input/input1
sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0
Registered led device: corgi:amber:charge
Registered led device: corgi:green:mail
TCP cubic registered
XScale DSP coprocessor detected.
sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:09 UTC (9)
Freeing init memory: 260K
mmc0: card lacks mandatory switch function, performance might suffer.
mmc0: new SD card at address 5c7b
mmcblk0: mmc0:5c7b SH256 249856KiB 
 mmcblk0: p1



U-Boot 1.1.4 (Aug 31 2008 - 22:32:16)


DRAM:  64 MB

NAND:128 MiB

*** Warning - bad CRC or NAND, using default environment


In:    serial

Out:   serial

Err:   serial

Hit any key to stop autoboot:  1  0 

U-Boot> 

U-Boot> ?   nand info


Device 0: NAND 128MiB 3,3V 8-bit, sector size 16 KiB

U-Boot> mtdparts

mtdparts variable not set, see 'help mtdparts'

no partitions defined


defaults:

mtdids  : nand0=sharpsl-nand

mtdparts: mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)

U-Boot> mtdparts

mtdparts variable not set, see 'help mtdparts'

no partitions defined


defaults:

mtdids  : nand0=sharpsl-nand

mtdparts: mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)

U-Boot> printenv

bootargs=console=tty1 console=ttyS0,115200 root=/dev/ram rw ramdisk_size=8192 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)

bootcmd=if testkey 101 ; then nand read.logical 0xa0800000 0x00060000 0x00540000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/ram rw ramdisk_size=8192 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home); bootm; fi; if testkey 2 ; then nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/mmcblk0p1 rootwait; bootm; fi; if testkey 18 ; then nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/hda1 rootwait; bootm; fi; if testkey 3 ; then nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/hdc1 rootwait; bootm; fi; nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home); bootm; 

bootdelay=1

baudrate=115200

stdin=serial

stdout=serial

stderr=serial

mtdids=nand0=sharpsl-nand


Environment size: 1133/131068 bytes

U-Boot> setenv        saveenv

Saving Environment to NAND...

Erasing Nand...Writing to Nand... done

U-Boot> printenv

bootargs=console=tty1 console=ttyS0,115200 root=/dev/ram rw ramdisk_size=8192 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home)

bootcmd=if testkey 101 ; then nand read.logical 0xa0800000 0x00060000 0x00540000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/ram rw ramdisk_size=8192 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home); bootm; fi; if testkey 2 ; then nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/mmcblk0p1 rootwait; bootm; fi; if testkey 18 ; then nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/hda1 rootwait; bootm; fi; if testkey 3 ; then nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/hdc1 rootwait; bootm; fi; nand read.logical 0xa0800000 0x005a0000 0x00160000; setenv bootargs console=tty1 console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=sharpsl-nand:7168k(smf),96M(root),-(home); bootm; 

bootdelay=1

baudrate=115200

stdin=serial

stdout=serial

stderr=serial

mtdids=nand0=sharpsl-nand


Environment size: 1133/131068 bytes

U-Boot>