Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Sun Jan 11 00:37:18 CET 2009 CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f Machine: SHARP Husky Ignoring unrecognised tag 0x00000000 Memory policy: ECC disabled, Data cache writeback Memory clock: 99.53MHz (*27) Run Mode clock: 199.07MHz (*2) Turbo Mode clock: 398.13MHz (*2.0, active) CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=tty1 console=ttyS0,115200n8 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [tty1] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 62616KB available (1888K code, 163K data, 200K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Sharp Scoop Device found at 0x10800000 -> 0xc4806000 PXA CPU frequency change support initialized JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc. msgmni has been set to 122 io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Corgi Backlight Driver Initialized. Found w100 at 0x08000000. Console: switching to colour frame buffer device 80x30 fb0: w100fb frame buffer device pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART console [ttyS0] enabled pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART loop: module loaded Uniform Multi-Platform E-IDE driver ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx Sharp SL series flash device: 800000 at 0 Using static partition definition Creating 1 MTD partitions on "sharpsl-flash": 0x00120000-0x007f0000 : "Boot PROM Filesystem" NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 32 at 0x00080000 Bad eraseblock 1440 at 0x01680000 Creating 3 MTD partitions on "sharpsl-nand": 0x00000000-0x00700000 : "System Area" 0x00700000-0x03c00000 : "Root Filesystem" 0x03c00000-0x08000000 : "Home Filesystem" pxa2xx_udc: version 30-June-2007 zero gadget: Gadget Zero, version: Earth Day 2008 zero gadget: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk mice: PS/2 mouse device common for all mice input: Corgi Keyboard as /class/input/input0 sharpsl_rc_init input: Corgi Touchscreen as /class/input/input1 sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0 Registered led device: corgi:amber:charge Registered led device: corgi:green:mail XScale DSP coprocessor detected. sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:00:49 UTC (49) Freeing init memory: 200K I'm the init-process! Procfs mounted Console loglevel is set Line: Processor : XScale-PXA255 rev 6 (v5l) Line: BogoMIPS : 397.28 Line: Features : swp half thumb fastmult edsp Line: CPU implementer : 0x69 Line: CPU architecture: 5TE Line: CPU variant : 0x0 Line: CPU part : 0x2d0 Line: CPU revision : 6 Line: Cache type : undefined 5 Line: Cache clean : undefined 5 Line: Cache lockdown : undefined 5 Line: Cache format : Harvard Line: I size : 32768 Line: I assoc : 32 Line: I line length : 32 Line: I sets : 32 Line: D size : 32768 Line: D assoc : 32 Line: D line length : 32 Line: D sets : 32 Line: Line: Hardware : SHARP Husky + model is: SHARP Husky + comparing with Shepherd + comparing with Husky + angle found: 0 Model is checked Going to fb mode Probing /dev/mtdblock0 Probing /dev/mtdblock1 Probing /dev/mtdblock2 found /dev/mtdblock2 (jffs2) mount successful found kernel found command line Probing /dev/mtdblock3 found /dev/mtdblock3 (jffs2) mount successful found kernel found command line Probing /dev/mmcblk0 found /dev/mmcblk0 (ext2) mount failed /dev/mmcblk0: Invalid argument Probing /dev/mmcblk0p1 found /dev/mmcblk0p1 (ext2) mount successful found kernel found command line kexec_load_argv: /usr/sbin/kexec, -l, --command-line= console=ttyS0,115200n8 console=tty1 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait, /mnt/boot/zImage kexec_exec_argv: /usr/sbin/kexec, -l, --command-line= console=ttyS0,115200n8 console=tty1 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait Uncompressing Linux........................................................................................ done, booting the kernel. Linux version 2.6.26 (andrea@mizar) (gcc version 4.2.4) #1 PREEMPT Thu Jan 8 23:27:21 CET 2009 CPU: XScale-PXA255 [69052d06] revision 6 (ARMv5TE), cr=0000397f Machine: SHARP Husky Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 16384 DMA zone: 128 pages used for memmap DMA zone: 0 pages reserved DMA zone: 16256 pages, LIFO batch:3 Normal zone: 0 pages used for memmap Movable zone: 0 pages used for memmap Memory clock: 99.53MHz (*27) Run Mode clock: 398.13MHz (*4) Turbo Mode clock: 398.13MHz (*1.0, active) CPU0: D VIVT undefined 5 cache CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,115200n8 console=tty1 noinitrd dyntick=enable debug root=/dev/mmcblk0p1 rootfstype=ext2 rootwait PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 console [tty1] enabled Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 62080KB available (2520K code, 240K data, 84K init) Calibrating delay loop... 397.31 BogoMIPS (lpj=1986560) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 624 bytes NET: Registered protocol family 16 Sharp Scoop Device found at 0x10800000 -> 0xc4806000 Switched to high resolution mode on CPU 0 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 PXA CPU frequency change support initialized JFFS2 version 2.2. (NAND) (SUMMARY) 2001-2006 Red Hat, Inc. msgmni has been set to 121 io scheduler noop registered io scheduler anticipatory registered (default) Corgi Backlight Driver Initialized. Found w100 at 0x08000000. Console: switching to colour frame buffer device 80x30 fb0: w100fb frame buffer device pxa2xx-uart.0: ttyS0 at MMIO 0x40100000 (irq = 22) is a FFUART console [ttyS0] enabled pxa2xx-uart.1: ttyS1 at MMIO 0x40200000 (irq = 21) is a BTUART pxa2xx-uart.2: ttyS2 at MMIO 0x40700000 (irq = 20) is a STUART pxa2xx-uart.3: ttyS3 at MMIO 0x41600000 (irq = 7) is a HWUART loop: module loaded Uniform Multi-Platform E-IDE driver ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx Sharp SL series flash device: 800000 at 0 Using static partition definition Creating 1 MTD partitions on "sharpsl-flash": 0x00120000-0x007f0000 : "Boot PROM Filesystem" NAND device: Manufacturer ID: 0xec, Chip ID: 0x79 (Samsung NAND 128MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 32 at 0x00080000 Bad eraseblock 1440 at 0x01680000 Creating 3 MTD partitions on "sharpsl-nand": 0x00000000-0x00700000 : "System Area" 0x00700000-0x03c00000 : "Root Filesystem" 0x03c00000-0x08000000 : "Home Filesystem" pxa2xx_udc: version 30-June-2007 input: Corgi Keyboard as /class/input/input0 sharpsl_rc_init input: Corgi Touchscreen as /class/input/input1 sa1100-rtc sa1100-rtc: rtc core: registered sa1100-rtc as rtc0 I2C: i2c-0: PXA I2C adapter Registered led device: corgi:amber:charge Registered led device: corgi:green:mail TCP cubic registered XScale DSP coprocessor detected. sa1100-rtc sa1100-rtc: setting system clock to 1970-01-01 00:01:13 UTC (73) Waiting for root device /dev/mmcblk0p1... mmc0: card lacks mandatory switch function, performance might suffer. mmc0: new SD card at address 5c7b mmcblk0: mmc0:5c7b SH256 249856KiB mmcblk0: p1 VFS: Mounted root (ext2 filesystem) readonly. Freeing init memory: 84K NET: Registered protocol family 23 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.9 Bluetooth: L2CAP socket layer initialized Bluetooth: HIDP (Human Interface Emulation) ver 1.2 IrCOMM protocol (Dag Brattli) Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 ASoC version 0.13.2 wm8731: WM8731 Audio Codec 0.13 asoc: WM8731 <-> pxa2xx-i2s mapping ok NOHZ: local_softirq_pending 100 Bluetooth: BNEP (Ethernet Emulation) ver 1.2 Bluetooth: BNEP filters: protocol multicast ether gadget: using random self ethernet address ether gadget: using random host ethernet address usb0: Ethernet Gadget, version: May Day 2005 usb0: using pxa2xx_udc, OUT ep2out-bulk IN ep1in-bulk STATUS ep6in-bulk usb0: MAC 4a:a1:50:05:04:d2 usb0: HOST MAC 6e:81:d3:a4:66:ea usb0: RNDIS ready input: Touchscreen offscreen keys as /class/input/input2 .-------. | | .-. | | |-----.-----.-----.| | .----..-----.-----. | | | __ | ---'| '--.| .-'| | | | | | | | |--- || --'| | | ' | | | | '---'---'--'--'--. |-----''----''--' '-----'-'-'-' -' | '---' The Angstrom Distribution c7x0 ttyS0 Angstrom 2009.X-test-20090107 c7x0 ttyS0 c7x0 login: