smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Seagate Barracuda 7200.8 family Device Model: ST3200826A Serial Number: 3ND2DJWQ Firmware Version: 3.03 User Capacity: 200,049,647,616 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Fri May 15 22:32:48 2009 BST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 242) Self-test routine in progress... 20% of test remaining. Total time to complete Offline data collection: ( 430) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 67) minutes. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 061 052 006 Pre-fail Always - 92670108 3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0 4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 43 5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 087 060 030 Pre-fail Always - 479120877 9 Power_On_Hours 0x0032 074 074 000 Old_age Always - 22944 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 44 194 Temperature_Celsius 0x0022 044 047 000 Old_age Always - 44 (0 15 0 0) 195 Hardware_ECC_Recovered 0x001a 061 052 000 Old_age Always - 92670108 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 196 000 Old_age Always - 236 200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0 202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 236 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 236 occurred at disk power-on lifetime: 22932 hours (955 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 07 00 00 f0 Error: ICRC, ABRT 1 sectors at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 f0 00 00:22:34.262 READ DMA EXT 25 00 08 00 00 00 f0 00 00:22:33.847 READ DMA EXT 10 00 ff 00 00 00 f0 00 00:22:33.846 RECALIBRATE [OBS-4] 25 00 08 00 00 00 f0 00 00:22:33.844 READ DMA EXT 25 00 08 00 00 00 f0 00 00:22:33.844 READ DMA EXT Error 235 occurred at disk power-on lifetime: 22932 hours (955 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 07 00 00 f0 Error: ICRC, ABRT 1 sectors at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 f0 00 00:22:34.262 READ DMA EXT 10 00 ff 00 00 00 f0 00 00:22:33.847 RECALIBRATE [OBS-4] 25 00 08 00 00 00 f0 00 00:22:33.846 READ DMA EXT 25 00 08 00 00 00 f0 00 00:22:33.844 READ DMA EXT ef 02 00 00 00 00 f0 00 00:22:33.844 SET FEATURES [Enable write cache] Error 234 occurred at disk power-on lifetime: 22932 hours (955 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 07 00 00 f0 Error: ICRC, ABRT 1 sectors at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 f0 00 00:22:34.262 READ DMA EXT 25 00 08 00 00 00 f0 00 00:22:33.847 READ DMA EXT ef 02 00 00 00 00 f0 00 00:22:33.846 SET FEATURES [Enable write cache] 27 00 00 00 00 00 f0 00 00:22:33.844 READ NATIVE MAX ADDRESS EXT c6 00 00 00 00 00 f0 00 00:22:33.844 SET MULTIPLE MODE Error 233 occurred at disk power-on lifetime: 22932 hours (955 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 07 00 00 f0 Error: ICRC, ABRT 1 sectors at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 f0 00 00:22:05.509 READ DMA EXT ef 02 00 00 00 00 f0 00 00:22:33.847 SET FEATURES [Enable write cache] 27 00 00 00 00 00 f0 00 00:22:33.846 READ NATIVE MAX ADDRESS EXT c6 00 00 00 00 00 f0 00 00:22:33.844 SET MULTIPLE MODE 10 00 ff 00 00 00 f0 00 00:22:33.844 RECALIBRATE [OBS-4] Error 232 occurred at disk power-on lifetime: 22932 hours (955 days + 12 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 01 07 00 00 f0 Error: ICRC, ABRT 1 sectors at LBA = 0x00000007 = 7 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 25 00 08 00 00 00 f0 00 00:00:35.850 READ DMA EXT 25 00 08 00 00 00 f0 00 00:00:34.254 READ DMA EXT 10 00 ff 00 00 00 f0 00 00:00:42.468 RECALIBRATE [OBS-4] 25 00 08 00 00 00 f0 00 00:00:42.035 READ DMA EXT 25 00 08 00 00 00 f0 00 00:00:42.035 READ DMA EXT SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.