root@galactica:/var/log# smartctl --all /dev/sde smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: WDC WD3000HLFS-01G6U0 Serial Number: WD-WXL808031531 Firmware Version: 04.04V01 User Capacity: 300,069,052,416 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Sun May 31 16:14:46 2009 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (4680) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 58) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0003 196 195 021 Pre-fail Always - 3175 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 53 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x000e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 3995 10 Spin_Retry_Count 0x0012 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0012 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 53 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 149 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 150 194 Temperature_Celsius 0x0022 122 112 000 Old_age Always - 25 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0010 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 3 CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3 occurred at disk power-on lifetime: 3982 hours (165 days + 22 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 34 cf f3 03 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ea 00 00 00 00 00 00 08 49d+17:02:41.152 FLUSH CACHE EXIT 61 08 00 bf ac ee 22 08 49d+17:02:41.152 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 08 49d+17:02:41.151 FLUSH CACHE EXIT 61 28 00 df 7c 77 11 08 49d+17:02:40.943 WRITE FPDMA QUEUED 61 08 00 6f 60 46 03 08 49d+17:02:40.942 WRITE FPDMA QUEUED Error 2 occurred at disk power-on lifetime: 2787 hours (116 days + 3 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 34 cf f3 03 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ea 00 00 00 00 00 00 08 49d+17:02:41.314 FLUSH CACHE EXIT 61 08 00 bf ac ee 22 08 49d+17:02:41.314 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 08 49d+17:02:41.313 FLUSH CACHE EXIT 61 08 00 f7 7c 77 11 08 49d+17:02:41.110 WRITE FPDMA QUEUED 60 08 00 f7 7c 77 11 08 49d+17:02:41.109 READ FPDMA QUEUED Error 1 occurred at disk power-on lifetime: 1594 hours (66 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 34 cf f3 03 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ea 00 00 00 00 00 00 08 49d+17:02:41.869 FLUSH CACHE EXIT 61 08 00 bf ac ee 22 08 49d+17:02:41.869 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 08 49d+17:02:41.868 FLUSH CACHE EXIT ea 00 00 00 00 00 00 08 49d+17:02:40.195 FLUSH CACHE EXIT 61 08 00 bf ac ee 22 08 49d+17:02:40.195 WRITE FPDMA QUEUED SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.