ts detected ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.3: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: irq 16, io base 0xef80 uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected usb 4-1: new full speed USB device using uhci_hcd and address 2 hub 4-1:1.0: USB hub found hub 4-1:1.0: 4 ports detected ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: EHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 23, pci mem 0xfebffc00 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected hub 4-1:1.0: cannot disable port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 4-1:1.0: cannot disable port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 4-1:1.0: cannot disable port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: cannot reset port 1 (err = -71) hub 4-1:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 4-1:1.0: cannot disable port 1 (err = -71) hub 4-1:1.0: cannot disable port 1 (err = -71) hub 4-1:1.0: hub_port_status failed (err = -71) hub 4-1:1.0: hub_port_status failed (err = -71) hub 4-1:1.0: hub_port_status failed (err = -71) hub 4-1:1.0: hub_port_status failed (err = -71) hub 4-1:1.0: hub_port_status failed (err = -71) hub 4-1:1.0: hub_port_status failed (err = -71) usb 5-7: new high speed USB device using ehci_hcd and address 2 hub 5-7:1.0: USB hub found hub 5-7:1.0: 4 ports detected usb 4-1: USB disconnect, address 2 usb 5-7.1: new full speed USB device using ehci_hcd and address 3 usb 5-7.3: new high speed USB device using ehci_hcd and address 4 SCSI subsystem initialized Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning bootsplash: status on console 0 changed to on Vendor: Sony Model: HMP-U01 Rev: 1.0 Type: Direct-Access ANSI SCSI revision: 00 usb-storage: device scan complete SCSI device sda: 78126048 512-byte hdwr sectors (40001 MB) sda: Write Protect is off sda: Mode Sense: 00 2a 00 00 sda: assuming drive cache: write through SCSI device sda: 78126048 512-byte hdwr sectors (40001 MB) sda: Write Protect is off sda: Mode Sense: 00 2a 00 00 sda: assuming drive cache: write through /dev/scsi/host0/bus0/target0/lun0: Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0 EXT3 FS on hda5, internal journal libata version 1.10 loaded. ata_piix version 1.03 ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0xEFE0 ctl 0xEFAE bmdma 0xEF60 irq 18 ata2: SATA max UDMA/133 cmd 0xEFA0 ctl 0xEFAA bmdma 0xEF68 irq 18 ata1: dev 0 cfg 49:2f00 82:346b 83:7f21 84:4003 85:3469 86:3c01 87:4003 88:207f ata1: dev 0 ATA, max UDMA/133, 72303840 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi1 : ata_piix ata2: SATA port has no device. scsi2 : ata_piix Vendor: ATA Model: WDC WD360GD-00FN Rev: 35.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sdb: 72303840 512-byte hdwr sectors (37020 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 72303840 512-byte hdwr sectors (37020 MB) SCSI device sdb: drive cache: write back /dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 > Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 sata_promise version 1.01 ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 23 (level, low) -> IRQ 23 ata3: SATA max UDMA/133 cmd 0xE081E200 ctl 0xE081E238 bmdma 0x0 irq 23 ata4: SATA max UDMA/133 cmd 0xE081E280 ctl 0xE081E2B8 bmdma 0x0 irq 23 ata3: no device found (phy stat 00000000) scsi3 : sata_promise ata4: no device found (phy stat 00000000) scsi4 : sata_promise ieee1394: Initialized config rom entry `ip1394' sbp2: $Rev: 1219 $ Ben Collins Adding 1124508k swap on /dev/hda6. Priority:-1 extents:1 Linux video capture interface: v1.00 bttv: driver version 0.9.15 loaded bttv: using 4 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21 bttv0: Bt878 (rev 17) at 0000:02:0d.0, irq: 21, latency: 64, mmio: 0xfbefe000 bttv0: subsystem: 11bd:ff12 (UNKNOWN) please mail id, board name and the correct card= insmod option to kraxel@bytesex.org bttv0: using: Pinnacle PCTV Studio/Rave [card=39,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00ff27ff [init] bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: miro: id=9 tuner=3 radio=no stereo=no bttv0: using tuner=3 bttv0: i2c: checking for MSP34xx @ 0x80... not found bttv0: i2c: checking for TDA9875 @ 0xb0... not found bttv0: i2c: checking for TDA7432 @ 0x8a... not found bttv0: i2c: checking for TDA9887 @ 0x86... not found tuner: chip found at addr 0xc0 i2c-bus bt878 #0 [sw] tuner: type set to 3 (Philips (SECAM+PAL_BG) (FI1216MF, FM1216MF, FR1216MF)) bybt878 #0 [sw] bttv0: registered device video0 bttv0: registered device vbi0 bttv0: PLL: 28636363 => 35468950 .. ok bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI interrupt 0000:02:0d.1[A] -> GSI 21 (level, low) -> IRQ 21 bt878(0): Bt878 (rev 17) at 02:0d.1, irq: 21, latency: 64, memory: 0xfbeff000 gameport: pci0000:02:09.1 speed 1193 kHz hw_random hardware driver 1.0.0 loaded Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel i875 Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 32M @ 0xfc000000 kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. Supermount version 2.0.4 for kernel 2.6 ntfs: Ignoring new-style parameters in presence of obsolete ones NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE]. NTFS volume version 3.1. NTFS volume version 3.1. NTFS volume version 3.1. NTFS volume version 3.1. NTFS volume version 3.1. NTFS volume version 3.1. NTFS volume version 3.1. loop: loaded (max 8 devices) ohci1394: $Rev: 1223 $ Ben Collins ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 20 (level, low) -> IRQ 20 ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[20] MMIO=[feaff800-feafffff] Max Packet=[2048] ACPI: PCI interrupt 0000:02:09.2[B] -> GSI 22 (level, low) -> IRQ 22 ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[22] MMIO=[feaff000-feaff7ff] Max Packet=[2048] hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33) ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22 sk98lin: Network Device Driver v8.14.2.2 (beta) (C)Copyright 1999-2005 Marvell(R). ACPI: PCI interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 22 eth0: 3Com Gigabit LOM (3C940) PrefPort:A RlmtMode:Check Link State 8139too Fast Ethernet driver 0.9.27 ACPI: PCI interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 22 eth1: RealTek RTL8139 at 0xe0f8ec00, 00:00:e8:93:d9:1d, IRQ 22 eth1: Identified 8139 chip type 'RTL-8139A' eth1394: $Rev: 1224 $ Ben Collins eth1394: eth2: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) eth1394: eth3: IEEE-1394 IPv4 over 1394 Ethernet (fw-host1) ieee1394: Host added: ID:BUS[0-00:1023] GUID[00e01800001e537f] ieee1394: Host added: ID:BUS[1-01:1023] GUID[00023c0020006a01] ip_conntrack version 2.1 (4089 buckets, 32712 max) - 252 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ACPI: Power Button (FF) [PWRF] Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 NET: Registered protocol family 17 eth1: link up, 100Mbps, full-duplex, lpa 0x45E1 ip_tables: (C) 2000-2002 Netfilter core team ip_conntrack version 2.1 (4089 buckets, 32712 max) - 252 bytes per conntrack ACPI: PCI interrupt 0000:02:09.0[A] -> GSI 21 (level, low) -> IRQ 21 Bluetooth: Core ver 2.7 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.7 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM ver 1.5 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized NET: Registered protocol family 10 Disabled Privacy Extensions on device c03c77e0(lo) IPv6 over IPv4 tunneling driver Disabled Privacy Extensions on device dcbeb000(sit0) Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59 Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=1 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59 Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=2 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59 Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=3 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93 [drm] Initialized drm 1.0.0 20040925 ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 [drm] Initialized radeon 1.14.0 20050125 on minor 0: agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 4x mode [drm] Loading R200 Microcode Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93 vmmon: module license 'unspecified' taints kernel. /dev/vmmon[10083]: Module vmmon: registered with major=10 minor=165 /dev/vmmon[10083]: Module vmmon: initialized parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] /dev/vmnet: open called by PID 10161 (vmnet-bridge) /dev/vmnet: hub 0 does not exist, allocating memory. /dev/vmnet: port on hub 0 successfully opened bridge-eth1: enabling the bridge bridge-eth1: up bridge-eth1: already up bridge-eth1: attached Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=5 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93 /dev/vmnet: open called by PID 10195 (vmnet-natd) /dev/vmnet: hub 8 does not exist, allocating memory. /dev/vmnet: port on hub 8 successfully opened Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=113 TOS=0x00 PREC=0x00 TTL=255 ID=6 DF PROTO=UDP SPT=5353 DPT=5353 LEN=93 eth1: no IPv6 routers present eth0: no IPv6 routers present FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! /dev/vmnet: open called by PID 10738 (vmnet-netifup) /dev/vmnet: hub 1 does not exist, allocating memory. /dev/vmnet: port on hub 1 successfully opened /dev/vmnet: open called by PID 10745 (vmnet-netifup) /dev/vmnet: port on hub 8 successfully opened /dev/vmnet: open called by PID 10772 (vmnet-dhcpd) /dev/vmnet: port on hub 1 successfully opened /dev/vmnet: open called by PID 10785 (vmnet-dhcpd) /dev/vmnet: port on hub 8 successfully opened Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59 Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=97 TOS=0x00 PREC=0x00 TTL=255 ID=1 DF PROTO=UDP SPT=5353 DPT=5353 LEN=77 Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=192.168.1.101 DST=224.0.0.251 LEN=79 TOS=0x00 PREC=0x00 TTL=255 ID=2 DF PROTO=UDP SPT=5353 DPT=5353 LEN=59 bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 10640 bytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for pictureytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for pictureytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for pictureytes, v3). bootsplash: status on console 5 changed to on Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1929 TOS=0x00 PREC=0x00 TTL=255 ID=3 DF PROTO=UDP S Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1923 TOS=0x00 PREC=0x00 TTL=255 ID=4 DF PROTO=UDP S Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1927 TOS=0x00 PREC=0x00 TTL=255 ID=5 DF PROTO=UDP S Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=1923 TOS=0x00 PREC=0x00 TTL=255 ID=6 DF PROTO=UDP S Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=7 DF PROTO=UDP Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=8 DF PROTO=UDP vmnet1: no IPv6 routers present vmnet8: no IPv6 routers present Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=9 DF PROTO=UDP Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=10 DF PROTO=UDP bttv0: SCERR @ 1d0d6000,bits: OFLOW FDSR SCERR* Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=11 DF PROTO=UDP bttv0: PLL can sleep, using XTAL (28636363). bttv0: PLL: 28636363 => 35468950 .. ok Shorewall:net2all:DROP:IN=eth1 OUT= MAC= SRC=19213 TOS=0x00 PREC=0x00 TTL=255 ID=12 DF PRO