Bootdata ok (command line is root=/dev/sda1)
Linux version 2.6.17-gentoo-r5 (root@localhost) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #6 SMP Mon Aug 14 12:32:52 PDT 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
 BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007ffb0000 (usable)
 BIOS-e820: 000000007ffb0000 - 000000007ffbe000 (ACPI data)
 BIOS-e820: 000000007ffbe000 - 000000007ffe0000 (ACPI NVS)
 BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fecc0000 - 00000000fecc1000 (reserved)
 BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
DMI present.
ACPI: RSDP (v002 ACPIAM                                ) @ 0x00000000000fa960
ACPI: XSDT (v001 A M I  OEMXSDT  0x05000624 MSFT 0x00000097) @ 0x000000007ffb0100
ACPI: FADT (v003 A M I  OEMFACP  0x05000624 MSFT 0x00000097) @ 0x000000007ffb0290
ACPI: MADT (v001 A M I  OEMAPIC  0x05000624 MSFT 0x00000097) @ 0x000000007ffb0390
ACPI: MCFG (v001 A M I  OEMMCFG  0x05000624 MSFT 0x00000097) @ 0x000000007ffb0400
ACPI: OEMB (v001 A M I  AMI_OEM  0x05000624 MSFT 0x00000097) @ 0x000000007ffbe040
ACPI: DSDT (v001  A0498 A0498000 0x00000000 INTL 0x20060113) @ 0x0000000000000000
Scanning NUMA topology in Northbridge 24
Number of nodes 1
Node 0 MemBase 0000000000000000 Limit 000000007ffb0000
NUMA: Using 63 for the hash shift.
Using node hash shift of 63
Bootmem setup node 0 0000000000000000-000000007ffb0000
On node 0 totalpages: 515285
  DMA zone: 2283 pages, LIFO batch:0
  DMA32 zone: 513002 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:11 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:11 APIC version 16
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfecc0000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 3, address 0xfecc0000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:7ec00000)
Checking aperture...
CPU 0: aperture @ 54000000 size 32 MB
Aperture from northbridge cpu 0 too small (32 MB)
No AGP bridge found
Built 1 zonelists
Kernel command line: root=/dev/sda1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 1999.819 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Memory: 2057892k/2096832k available (3071k kernel code, 38544k reserved, 1667k data, 220k init)
Calibrating delay using timer specific routine.. 4002.37 BogoMIPS (lpj=8004755)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0(2) -> Node 0 -> Core 0
Using local APIC timer interrupts.
result 12498885
Detected 12.498 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 3999.89 BogoMIPS (lpj=7999782)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1(2) -> Node 0 -> Core 1
AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ stepping 02
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 567 cycles)
Brought up 2 CPUs
testing NMI watchdog ... OK.
migration_cost=219
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
Error attaching device data
Error attaching device data
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:02:00.0
PCI: Transparent bridge - 0000:00:13.1
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBPG._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.NBP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PA._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: ACPI device : hid PNP0A03
pnp: ACPI device : hid PNP0200
pnp: ACPI device : hid PNP0B00
pnp: ACPI device : hid PNP0800
pnp: ACPI device : hid PNP0C04
pnp: ACPI device : hid PNP0700
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0303
pnp: ACPI device : hid PNP0C02
pnp: ACPI device : hid PNP0C01
pnp: PnP ACPI: found 13 devices
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI-DMA: Disabling IOMMU.
pnp: the driver 'system' has been registered
pnp: match found with the PnP device '00:06' and the driver 'system'
pnp: 00:06: ioport range 0xc00-0xc0f has been reserved
pnp: 00:06: ioport range 0xd00-0xd0f has been reserved
pnp: 00:06: ioport range 0xa20-0xa2f has been reserved
pnp: 00:06: ioport range 0xa30-0xa3f has been reserved
pnp: match found with the PnP device '00:07' and the driver 'system'
pnp: match found with the PnP device '00:08' and the driver 'system'
pnp: match found with the PnP device '00:09' and the driver 'system'
pnp: match found with the PnP device '00:0b' and the driver 'system'
pnp: match found with the PnP device '00:0c' and the driver 'system'
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
  IO window: c000-cfff
  MEM window: fbc00000-fbcfffff
  PREFETCH window: d8000000-dfffffff
PCI: Bridge: 0000:00:03.0
  IO window: d000-dfff
  MEM window: fbd00000-fbdfffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.1
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: efe00000-efefffff
PCI: Bridge: 0000:00:03.2
  IO window: disabled.
  MEM window: fbe00000-fbefffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.3
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: eff00000-efffffff
PCI: Bridge: 0000:00:13.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:08:07.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: f0000000-f7ffffff
PCI: Bridge: 0000:00:13.1
  IO window: e000-efff
  MEM window: fbf00000-fbffffff
  PREFETCH window: f0000000-f7ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:02.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:03.0 to 64
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 35 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:03.1 to 64
GSI 19 sharing vector 0xC1 and IRQ 19
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 39 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:03.2 to 64
GSI 20 sharing vector 0xC9 and IRQ 20
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 43 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:03.3 to 64
PCI: Setting latency timer of device 0000:00:13.0 to 64
PCI: Setting latency timer of device 0000:00:13.1 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
Total HugeTLB memory allocated, 0
SGI XFS with large block/inode numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 27 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie02]
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 31 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie02]
ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 35 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:03.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.1:pcie00]
Allocate Port Service[0000:00:03.1:pcie02]
ACPI: PCI Interrupt 0000:00:03.2[C] -> GSI 39 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:03.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.2:pcie00]
Allocate Port Service[0000:00:03.2:pcie02]
ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 43 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:03.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.3:pcie00]
Allocate Port Service[0000:00:03.3:pcie02]
Real Time Clock Driver v1.12ac
Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0)
Linux agpgart interface v0.101 (c) Dave Jones
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ACPI: Processor [P001] (supports 16 throttling states)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
pnp: the driver 'serial' has been registered
pnp: the driver 'i8042 kbd' has been registered
pnp: match found with the PnP device '00:0a' and the driver 'i8042 kbd'
pnp: the driver 'i8042 aux' has been registered
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
GSI 21 sharing vector 0x42 and IRQ 21
ACPI: PCI Interrupt 0000:08:09.0[A] -> GSI 19 (level, low) -> IRQ 66
e100: eth0: e100_probe: addr 0xfbfff000, irq 66, MAC addr 00:02:B3:E6:86:68
Marvell 88E1101: Registered new driver
Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.5 loaded
cx2388x blackbird driver version 0.0.5 loaded
cx2388x alsa driver version 0.0.5 loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 7
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA unknown (rev 07) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: LITE-ON DVD SOHD-16P9S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: ATAPI 48X DVD-ROM drive, 254kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
GSI 22 sharing vector 0x4A and IRQ 22
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 21 (level, low) -> IRQ 74
sata_via 0000:00:0f.0: routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xBC00 ctl 0xB882 bmdma 0xB400 irq 74
ata2: SATA max UDMA/133 cmd 0xB800 ctl 0xB482 bmdma 0xB408 irq 74
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:bc01 87:4023 88:40ff
ata1: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: SATA link up 1.5 Gbps (SStatus 113)
ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:bc01 87:4023 88:40ff
ata2: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_via
  Vendor: ATA       Model: SAMSUNG HD160JJ   Rev: ZM10
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: ATA       Model: SAMSUNG HD160JJ   Rev: ZM10
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
 sdb: sdb1
 sdb1: <bsd: sdb5 sdb6 sdb7 sdb8 sdb9 >
sd 1:0:0:0: Attached scsi disk sdb
ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 74
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:10.4: irq 74, io mem 0xfbbffc00
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
GSI 23 sharing vector 0x52 and IRQ 23
ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 20 (level, low) -> IRQ 82
PCI: VIA IRQ fixup for 0000:00:10.0, from 5 to 2
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.0: irq 82, io base 0x0000ac00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
GSI 24 sharing vector 0x5A and IRQ 24
ACPI: PCI Interrupt 0000:00:10.1[B] -> GSI 22 (level, low) -> IRQ 90
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.1: irq 90, io base 0x0000a880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> GSI 21 (level, low) -> IRQ 74
PCI: VIA IRQ fixup for 0000:00:10.2, from 3 to 10
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.2: irq 74, io base 0x0000a800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
GSI 25 sharing vector 0x62 and IRQ 25
ACPI: PCI Interrupt 0000:00:10.3[D] -> GSI 23 (level, low) -> IRQ 98
PCI: VIA IRQ fixup for 0000:00:10.3, from 7 to 2
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:10.3: irq 98, io base 0x0000a480
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Intel 810 + AC97 Audio, version 1.01, 12:31:05 Aug 14 2006
Advanced Linux Sound Architecture Driver Version 1.0.11rc4 (Wed Mar 22 10:27:24 2006 UTC).
ALSA device list:
  No soundcards found.
oprofile: using NMI interrupt.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.60.2)
powernow-k8: MP systems not supported by PSB BIOS structure
powernow-k8: MP systems not supported by PSB BIOS structure
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 220k freed
GSI 26 sharing vector 0x6A and IRQ 26
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 24 (level, low) -> IRQ 106
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=325.00 Mhz, System=200.00 MHz
radeonfb: PLL min 20000 max 40000
ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.7.0 (tagged release) loading
ivtv:  Linux version: 2.6.17-gentoo-r5 SMP mod_unload gcc-3.4
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
radeonfb: Monitor 1 type CRT found
radeonfb: Monitor 2 type no found
radeonfb (0000:02:00.0): ATI Radeon [` 
ivtv0: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
GSI 27 sharing vector 0x72 and IRQ 27
ACPI: PCI Interrupt 0000:09:08.0[A] -> GSI 17 (level, low) -> IRQ 114
wm8775 4-001b: chip found @ 0x36 (ivtv i2c driver #0)
tuner 4-0060: TEA5767 detected.
tuner 4-0060: chip found @ 0xc0 (ivtv i2c driver #0)
tuner 4-0060: type set to 62 (Philips TEA5767HN FM Radio)
tuner 4-0061: chip found @ 0xc2 (ivtv i2c driver #0)
cx25840 4-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #0)
cx25840 4-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
tveeprom 4-0050: Hauppauge model 23552, rev E587, serial# 8826299
tveeprom 4-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type 70)
tveeprom 4-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 4-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
tveeprom 4-0050: audio processor is CX25843 (idx 37)
tveeprom 4-0050: decoder processor is CX25843 (idx 30)
tveeprom 4-0050: has radio, has no IR remote
ivtv0: This is the first unit of a PVR500
ivtv0: Failed to load module cx25840
ivtv0: Failed to load module wm8775
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0: Encoder revision: 0x02050032
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0: Create encoder radio stream
tuner 4-0061: type set to 70 (Samsung TCPN 2121P30A)
ivtv0: Initialized WinTV PVR 500 (unit #1), card #0
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected Hauppauge WinTV PVR-150 card (cx23416 based)
GSI 28 sharing vector 0x7A and IRQ 28
ACPI: PCI Interrupt 0000:09:09.0[A] -> GSI 18 (level, low) -> IRQ 122
wm8775 5-001b: chip found @ 0x36 (ivtv i2c driver #1)
tuner 5-0061: chip found @ 0xc2 (ivtv i2c driver #1)
cx25840 5-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 5-0044: loaded v4l-cx25840.fw firmware (16382 bytes)
tveeprom 5-0050: Hauppauge model 23552, rev E587, serial# 8826299
tveeprom 5-0050: tuner model is Samsung TCPN 2121P30A (idx 87, type 70)
tveeprom 5-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 5-0050: second tuner model is Philips TEA5768HL FM Radio (idx 101, type 62)
tveeprom 5-0050: audio processor is CX25843 (idx 37)
tveeprom 5-0050: decoder processor is CX25843 (idx 30)
tveeprom 5-0050: has radio, has no IR remote
ivtv1: This is the second unit of a PVR500
ivtv1: Correcting tveeprom data: no radio present on second unit
ivtv1: Failed to load module cx25840
ivtv1: Failed to load module wm8775
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1: Encoder revision: 0x02050032
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
tuner 5-0061: type set to 70 (Samsung TCPN 2121P30A)
ivtv1: Initialized WinTV PVR 500 (unit #2), card #1
ivtv:  ====================  END INIT IVTV  ====================
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 4008208k swap on /dev/sda2.  Priority:-1 extents:1 across:4008208k
e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex