Linux version 2.6.17.11 (root@Slackware) (gcc version 3.3.6) #2 SMP PREEMPT Tue Sep 12 13:33:12 EEST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003dfb0000 (usable) BIOS-e820: 000000003dfb0000 - 000000003dfbe000 (ACPI data) BIOS-e820: 000000003dfbe000 - 000000003dfe0000 (ACPI NVS) BIOS-e820: 000000003dfe0000 - 000000003e000000 (reserved) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. found SMP MP-table at 000ff780 On node 0 totalpages: 229376 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v002 ACPIAM ) @ 0x000fb1a0 ACPI: XSDT (v001 A M I OEMXSDT 0x11000511 MSFT 0x00000097) @ 0x3dfb0100 ACPI: FADT (v003 A M I OEMFACP 0x11000511 MSFT 0x00000097) @ 0x3dfb0290 ACPI: MADT (v001 A M I OEMAPIC 0x11000511 MSFT 0x00000097) @ 0x3dfb0390 ACPI: MCFG (v001 A M I OEMMCFG 0x11000511 MSFT 0x00000097) @ 0x3dfb0400 ACPI: OEMB (v001 A M I AMI_OEM 0x11000511 MSFT 0x00000097) @ 0x3dfbe040 ACPI: DSDT (v001 A0313 A0313001 0x00000001 INTL 0x02002026) @ 0x00000000 ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:4 APIC version 20 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 40000000 (gap: 3e000000:c1780000) Built 1 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=301 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 3000.898 MHz processor. Using pmtmr for high-res timesource Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 904696k/917504k available (1958k kernel code, 12404k reserved, 909k data, 180k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 6005.00 BogoMIPS (lpj=3002504) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000649d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000649d 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 20000000 00000000 00000180 0000649d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available Checking 'hlt' instruction... OK. Freeing SMP alternatives: 12k freed CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 5997.55 BogoMIPS (lpj=2998776) CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000649d 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000649d 00000000 00000000 monitor/mwait feature present. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 20000000 00000000 00000180 0000649d 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (24) available CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03 Total of 2 processors activated (12002.56 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=1000 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=2 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 4000-403f claimed by ali7101 ACPI Boot video device is 0000:01:05.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2P._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 *15), disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15), disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15), disabled. ACPI: PCI Interrupt Link [LNKP] (IRQs 3 4 *5 6 7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 3 of device 0000:00:00.0 PCI: Bridge: 0000:00:01.0 IO window: a000-cfff MEM window: bfd00000-dfdfffff PREFETCH window: 9fc00000-bfbfffff PCI: Bridge: 0000:00:19.0 IO window: d000-dfff MEM window: dfe00000-dfefffff PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:19.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) IPv4 FIB: Using LC-trie version 0.407 TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. io scheduler noop registered io scheduler deadline registered (default) vesafb: framebuffer at 0xa0000000, mapped to 0xf8880000, using 3072k, total 32768k vesafb: mode is 1024x768x16, linelength=2048, pages=20 vesafb: protected mode interface info at c000:552e vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Processor [CPU1] (supports 8 throttling states) Real Time Clock Driver v1.12ac [drm] Initialized drm 1.0.1 20051102 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using monotonic_clock(). Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport0: PC-style at 0x378 (0x778) [PCSPP(,...)] parport0: irq 7 detected Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) nbd: registered device at major 43 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt 0000:02:14.0[A] -> GSI 17 (level, low) -> IRQ 169 eth0: RealTek RTL8139 at 0xd800, 00:50:fc:8c:3e:67, IRQ 169 eth0: Identified 8139 chip type 'RTL-8100B/8139D' uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29) ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 20 (level, low) -> IRQ 177 eth1: ULi M5263 at pci0000:00:1b.0, 00:15:f2:b0:5d:dd, irq 177. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 0000:00:1f.0 ACPI: PCI Interrupt 0000:00:1f.0[A] -> GSI 21 (level, low) -> IRQ 185 ALI15X3: chipset revision 199 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xff08-0xff0f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: ST380021A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-ST GCE-8525B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes not supported hda: hda1 hda2 hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 23 (level, low) -> IRQ 193 ehci_hcd 0000:00:1c.3: EHCI Host Controller ehci_hcd 0000:00:1c.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1c.3: debug port 1 PCI: cache line size of 128 is not supported by device 0000:00:1c.3 ehci_hcd 0000:00:1c.3: irq 193, io mem 0xdffff800 ehci_hcd 0000:00:1c.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169 ohci_hcd 0000:00:1c.0: OHCI Host Controller ohci_hcd 0000:00:1c.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:1c.0: irq 169, io mem 0xdfffc000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 18 (level, low) -> IRQ 201 ohci_hcd 0000:00:1c.1: OHCI Host Controller ohci_hcd 0000:00:1c.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:1c.1: irq 201, io mem 0xdfffd000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 19 (level, low) -> IRQ 209 ohci_hcd 0000:00:1c.2: OHCI Host Controller ohci_hcd 0000:00:1c.2: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:1c.2: irq 209, io mem 0xdfffe000 usb 1-5: new high speed USB device using ehci_hcd and address 4 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 3 ports detected usb 1-5: configuration #1 chosen from 1 choice USB Universal Host Controller Interface driver v3.0 usb 3-1: new full speed USB device using ohci_hcd and address 2 usb 3-1: configuration #1 chosen from 1 choice usb 3-2: new full speed USB device using ohci_hcd and address 3 usb 3-2: configuration #1 chosen from 1 choice drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x03F0 pid 0x7204 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver usbcore: registered new driver libusual libusual: modprobe for usb-storage succeeded, but module is not present PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available Starting balanced_irq Using IPI Shortcut mode input: AT Translated Set 2 keyboard as /class/input/input0 ReiserFS: hda1: found reiserfs format "3.6" with standard journal input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 ReiserFS: hda1: using ordered data mode ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda1: checking transaction log (hda1) ReiserFS: hda1: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 180k freed Adding 2048276k swap on /dev/hda2. Priority:-1 extents:1 across:2048276k eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 ACPI: PCI Interrupt 0000:00:1d.0[C] -> GSI 22 (level, low) -> IRQ 217 uli526x: eth1 NIC Link is Up 100 Mbps Full duplex ip_conntrack version 2.4 (7168 buckets, 57344 max) - 204 bytes per conntrack ip_tables: (C) 2000-2006 Netfilter Core Team usb 1-5: USB disconnect, address 4 usb 1-5: new high speed USB device using ehci_hcd and address 5 usb 1-5: configuration #1 chosen from 1 choice Initializing USB Mass Storage driver... usb-storage: USB Mass Storage device detected usb-storage: -- associate_dev usb-storage: Vendor: 0x058f, Product: 0x6331, Revision: 0x0102 usb-storage: Interface Subclass: 0x06, Protocol: 0x50 usb-storage: Transport: Bulk usb-storage: Protocol: Transparent SCSI scsi0 : SCSI emulation for USB Mass Storage devices usb-storage: *** thread sleeping. usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning usbcore: registered new driver usb-storage USB Mass Storage support registered. usb-storage: usb_stor_control_msg: rq=fe rqtype=a1 value=0000 index=00 len=1 usb-storage: GetMaxLUN command result is 1, data is 0 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Command INQUIRY (6 bytes) usb-storage: 12 00 00 00 24 00 usb-storage: Bulk Command S 0x43425355 T 0x1 L 36 F 128 Trg 0 LUN 0 CL 6 usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes usb-storage: Status code 0; transferred 31/31 usb-storage: -- transfer complete usb-storage: Bulk command transfer result=0 usb-storage: usb_stor_bulk_transfer_sglist: xfer 36 bytes, 1 entries usb-storage: Status code 0; transferred 36/36 usb-storage: -- transfer complete usb-storage: Bulk data transfer result 0x0 usb-storage: Attempting to get CSW... usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes usb-storage: Status code 0; transferred 13/13 usb-storage: -- transfer complete usb-storage: Bulk status result = 0 usb-storage: Bulk Status S 0x53425355 T 0x1 R 0 Stat 0x0 usb-storage: scsi cmd done, result=0x0 usb-storage: *** thread sleeping. Vendor: Multi Model: Flash Reader Rev: 1.00 Type: Direct-Access ANSI SCSI revision: 00 0:0:0:0: Attached scsi generic sg0 type 0 usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (1:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (2:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (3:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (4:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (5:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (6:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: queuecommand called usb-storage: *** thread awakened. usb-storage: Bad target number (7:0) usb-storage: scsi cmd done, result=0x40000 usb-storage: *** thread sleeping. usb-storage: device scan complete