smartctl version 5.36 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: SAMSUNG MP0402H Serial Number: S03WJ10Y758618 Firmware Version: UC100-14 User Capacity: 40.007.762.432 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Sun Sep 17 11:39:41 2006 CEST ==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details. SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF ENABLE/DISABLE COMMANDS SECTION === SMART Enabled. === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (2400) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 40) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always - 2496 4 Start_Stop_Count 0x0032 001 001 000 Old_age Always - 147299 5 Reallocated_Sector_Ct 0x0033 100 100 011 Pre-fail Always - 0 7 Seek_Error_Rate 0x000f 100 100 051 Pre-fail Always - 0 8 Seek_Time_Performance 0x0025 099 099 015 Pre-fail Offline - 15690 9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 218130 10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1455 191 G-Sense_Error_Rate 0x0012 100 100 000 Old_age Always - 662 194 Temperature_Celsius 0x0022 073 070 000 Old_age Always - 55 195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 32750992 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 1 200 Multi_Zone_Error_Rate 0x000a 100 100 051 Old_age Always - 0 201 Soft_Read_Error_Rate 0x0012 100 100 000 Old_age Always - 0 223 Load_Retry_Count 0x0012 100 100 000 Old_age Always - 3 225 Load_Cycle_Count 0x0012 071 071 000 Old_age Always - 293695 255 Unknown_Attribute 0x000a 100 100 051 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 1457 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 1457 occurred at disk power-on lifetime: 1813 hours (75 days + 13 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 f0 00 00 00 e0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 03 f0 00 00 00 e0 00 00:00:05.500 SET MAX UNLOCK ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands] 00 00 01 01 00 00 a0 00 00:00:05.438 NOP [Abort queued commands] 90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC Error 1456 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 f0 00 00 00 e0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 03 f0 00 00 00 e0 00 00:00:05.500 SET MAX UNLOCK ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands] 00 00 01 01 00 00 a0 00 00:00:05.438 NOP [Abort queued commands] 90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC Error 1455 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 f0 00 00 00 e0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 03 f0 00 00 00 e0 00 00:00:05.500 SET MAX UNLOCK ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands] 00 00 01 01 00 00 a0 00 00:00:05.438 NOP [Abort queued commands] 90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC Error 1454 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 f0 00 00 00 e0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 03 f0 00 00 00 e0 00 00:00:05.688 SET MAX UNLOCK ec 00 01 00 00 00 a0 00 00:00:05.688 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:00:05.688 NOP [Abort queued commands] 00 00 01 01 00 00 a0 00 00:00:05.625 NOP [Abort queued commands] 90 00 01 01 00 00 a0 00 00:00:05.625 EXECUTE DEVICE DIAGNOSTIC Error 1453 occurred at disk power-on lifetime: 1810 hours (75 days + 10 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 f0 00 00 00 e0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- f9 03 f0 00 00 00 e0 00 00:00:05.563 SET MAX UNLOCK ec 00 01 00 00 00 a0 00 00:00:05.500 IDENTIFY DEVICE 00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands] 00 00 01 01 00 00 a0 00 00:00:05.500 NOP [Abort queued commands] 90 00 01 01 00 00 a0 00 00:00:05.438 EXECUTE DEVICE DIAGNOSTIC SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 1817 - # 2 Short offline Completed without error 00% 1208 - SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1 SMART Selective self-test log data structure revision number 0 Warning: ATA Specification requires selective self-test log data structure revision number = 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.