root@sluggy:~# dmesg
Linux version 2.6.11.2 (openslug@openslug.org) (gcc version 3.4.4) #1 Tue Jun 21 00:46:18 PDT 2005
CPU: XScale-IXP42x Family [690541f1] revision 1 (ARMv5TE)
CPU0: D VIVT undefined 5 cache
CPU0: I cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
CPU0: D cache: 32768 bytes, associativity 32, 32 byte lines, 32 sets
Machine: Linksys NSLU2
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 8192
  DMA zone: 8192 pages, LIFO batch:2
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=/dev/mtdblock4 rw rootfstype=jffs2 mem=32M@0x00000000 init=/linuxrc reboot=s console=ttyS0,115200n8
PID hash table entries: 256 (order: 8, 4096 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 32MB = 32MB total
Memory: 30512KB available (1614K code, 161K data, 88K init)
Calibrating delay loop... 133.12 BogoMIPS (lpj=665600)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
PCI: IXP4xx is host
PCI: IXP4xx Using indirect access for memory space
PCI: bus0: Fast back to back transfers disabled
dmabounce: registered device 0000:00:01.0 on pci bus
dmabounce: registered device 0000:00:01.1 on pci bus
dmabounce: registered device 0000:00:01.2 on pci bus
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
OpenN2 Misc I/O Driver Version 0.1.7
init_jiffy=-29961
setup_interrupts - jiffies=-29961 init_jiffy=-29961
enable_irq(22) unbalanced from c00111e4
enable_irq(29) unbalanced from c00111ec
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
IXP4xx Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
ttyS0 at MMIO 0xc8000000 (irq = 15) is a XScale
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
IXP4XX-Flash0: Found 1 x16 devices at 0x0 in 16-bit bank
IXP4XX-Flash0: Found an alias at 0x800000 for the chip at 0x0
 Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
0: offset=0x0,size=0x20000,blocks=64
Searching for RedBoot partition table in IXP4XX-Flash0 at offset 0x7e0000
6 RedBoot partitions found on MTD device IXP4XX-Flash0
Creating 6 MTD partitions on "IXP4XX-Flash0":
0x00000000-0x00040000 : "RedBoot"
0x00040000-0x00060000 : "SysConf"
0x00060000-0x00160000 : "Kernel"
0x00160000-0x00180000 : "Ramdisk"
0x00180000-0x007e0000 : "Flashdisk"
0x007e0000-0x00800000 : "FIS directory"
PCI: enabling device 0000:00:01.2 (0140 -> 0142)
ehci_hcd 0000:00:01.2: EHCI Host Controller
ehci_hcd 0000:00:01.2: irq 26, pci mem 0x48002000
ehci_hcd 0000:00:01.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:01.2: park 0
ehci_hcd 0000:00:01.2: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 5 ports detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: enabling device 0000:00:01.0 (0140 -> 0142)
ohci_hcd 0000:00:01.0: OHCI Host Controller
ohci_hcd 0000:00:01.0: irq 28, pci mem 0x48000000
ohci_hcd 0000:00:01.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: enabling device 0000:00:01.1 (0140 -> 0142)
ohci_hcd 0000:00:01.1: OHCI Host Controller
ohci_hcd 0000:00:01.1: irq 27, pci mem 0x48001000
ohci_hcd 0000:00:01.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-1: new high speed USB device using ehci_hcd and address 2
Initializing USB Mass Storage driver...
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 1 port detected
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
i2c /dev entries driver
LOADED Xicor x1205 RTC Dvr v0.9.3.3NPW
Xicor x1205 RTC Dvr v0.9.3.3NPW attached on adapter 
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
NET: Registered protocol family 1
usb 1-1.1: new high speed USB device using ehci_hcd and address 3
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
  Vendor: Yakumo    Model: Quicksave 2.0     Rev: 1.00
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
ioctl_internal_command: <0 0 0 0> return code = 8000002
   : Current: sense key=0x0
    ASC=0x0 ASCQ=0x0
SCSI device sda: 512000 512-byte hdwr sectors (262 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
 sda: sda1
ioctl_internal_command: <0 0 0 0> return code = 8000002
   : Current: sense key=0x0
    ASC=0x0 ASCQ=0x0
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-storage: device scan complete
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 88K
ixp400: module license 'unspecified' taints kernel.
Module init.
ixp425_eth: 
Initializing IXP425 NPE Ethernet driver software v. 1.1A 
ixp425_eth: CPU clock speed (approx) = 0 MHz
[error] ixEthMiiPhyScan : unexpected Mii PHY ID 00008201
ixp425_eth: npe0 is using the PHY at address 0
ixp425_eth: npe1 is using the PHY at address 1
ixp425_eth: ixEthMiiLinkStatus failed on PHY0.
        Can't determine
the auto negotiated parameters. Using default values.