SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:02: ioport range 0x4000-0x407f could not be reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: ec000000-edffffff
  PREFETCH window: e8000000-ebffffff
PCI: Bus 2, cardbus bridge: 0000:00:0c.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 10000000-11ffffff
  MEM window: 12000000-13ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0c.1
  IO window: 00001800-000018ff
  IO window: 00001c00-00001cff
  PREFETCH window: 14000000-15ffffff
  MEM window: 16000000-17ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
io scheduler noop registered
io scheduler cfq registered (default)
vesafb: framebuffer at 0xe8000000, mapped to 0xcf880000, using 6144k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:86ee
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 33714 bytes,<6>...found (1024x768, 15341 bytes, v3).
Console: switching to colour frame buffer device 120x44
fb0: VESA VGA frame buffer device
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xdf00-0xdf07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xdf08-0xdf0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Probing IDE interface ide1...
hdc: SanDisk SDCFB-256, CFA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide0...
hdc: max request size: 128KiB
hdc: 501760 sectors (256 MB) w/1KiB Cache, CHS=980/16/32
 hdc: hdc1 hdc2 < hdc5 hdc6 hdc7 >
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1
ACPI: (supports S0 S1 S4 S5)
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
RAMDISK: Couldn't find valid RAM disk image starting at 0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k freed
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:11.5 to 64
usbcore: registered new driver usbfs
usbcore: registered new driver hub
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdc6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on hdc7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA CLE266 chipset
agpgart: AGP aperture is 64M @ 0xe4000000
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xcf804000, 00:40:48:b1:62:36, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
eth1: RealTek RTL8139 at 0xcfe98000, 00:40:48:b1:62:35, IRQ 10
eth1:  Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
eth2: RealTek RTL8139 at 0xcfe9a000, 00:40:48:b1:62:34, IRQ 11
eth2:  Identified 8139 chip type 'RTL-8100B/8139D'
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ 7
eth3: RealTek RTL8139 at 0xcfe9c000, 00:40:48:b1:62:33, IRQ 7
eth3:  Identified 8139 chip type 'RTL-8100B/8139D'
eth2: link down
eth3: link down
eth1: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link down
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
NET: Registered protocol family 17
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0c.0 [3412:7856]
Yenta: ISA IRQ mask 0x0008, PCI irq 11
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:00:0c.1 [3412:7856]
Yenta: ISA IRQ mask 0x0008, PCI irq 10
Socket status: 30000006
cs: IO port probe 0x100-0x4ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x4ff: excluding 0x1f0-0x1f7 0x3f0-0x3ff 0x4d0-0x4d7
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff
cs: IO port probe 0xa00-0xaff: clean.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: VIA IRQ fixup for 0000:00:10.0, from 5 to 11
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 11, io base 0x0000dc00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 10, io base 0x0000dd00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 11, io base 0x0000de00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usb 1-2: new low speed USB device using uhci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator as /class/input/input0
input: USB HID v1.11 Keyboard [C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator] on usb-0000:00:10.0-2
input: C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator as /class/input/input1
input: USB HID v1.11 Mouse [C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator] on usb-0000:00:10.0-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 7 (level, low) -> IRQ 7
ehci_hcd 0000:00:10.3: EHCI Host Controller
ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
ehci_hcd 0000:00:10.3: irq 7, io mem 0xee01d000
ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 1-2: USB disconnect, address 2
usb 1-2: new low speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
input: C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator as /class/input/input2
input: USB HID v1.11 Keyboard [C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator] on usb-0000:00:10.0-2
input: C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator as /class/input/input3
input: USB HID v1.11 Mouse [C&C Technology Inc. HID Keyboard/Mouse PS/2 to USB Translator] on usb-0000:00:10.0-2
Real Time Clock Driver v1.12ac
input: PC Speaker as /class/input/input4
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Fan [FAN] (on)
ACPI: Thermal Zone [THRM] (-269 C)
pccard: PCMCIA card inserted into slot 1
cs: memory probe 0xa0000000-0xa0ffffff: clean.
pcmcia: registering new device pcmcia1.0