sudo /usr/sbin/smartctl -a /dev/hdb smartctl version 5.34 [i686-pc-linux-gnu] Copyright (C) 2002-5 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Maxtor DiamondMax 10 family Device Model: Maxtor 6B200P0 Serial Number: B41XGDVH Firmware Version: BAH41BY0 User Capacity: 203,928,109,056 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Wed Oct 4 17:54:39 2006 EEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (1622) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 82) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0027 206 206 063 Pre-fail Always - 4297 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 22 5 Reallocated_Sector_Ct 0x0033 211 211 063 Pre-fail Always - 427 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 248 227 187 Pre-fail Always - 42616 9 Power_On_Minutes 0x0032 248 248 000 Old_age Always - 803h+33m 10 Spin_Retry_Count 0x002b 253 252 157 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 251 251 000 Old_age Always - 811 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0 194 Temperature_Celsius 0x0032 036 253 000 Old_age Always - 42 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 1937 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 251 248 000 Old_age Offline - 25 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 199 199 000 Old_age Offline - 0 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 252 000 Old_age Always - 1 202 TA_Increase_Count 0x000a 253 252 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 0 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0 208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0 209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0 210 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 211 Unknown_Attribute 0x0032 253 252 000 Old_age Always - 0 212 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 3473 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 3473 occurred at disk power-on lifetime: 1606 hours (66 days + 22 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 57 4a 04 33 33 b7 fc Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- fc 00 04 33 33 b7 fc 00 00:33:37.739 [VENDOR SPECIFIC] fc 00 04 2f 33 b7 fc 00 00:33:31.884 [VENDOR SPECIFIC] fc 00 08 37 33 b7 fc 00 00:33:31.798 [VENDOR SPECIFIC] fc 00 08 2f 33 b7 fc 00 00:33:25.865 [VENDOR SPECIFIC] fc 00 10 2f 33 b7 fc 00 00:33:20.011 [VENDOR SPECIFIC] Error 3472 occurred at disk power-on lifetime: 1606 hours (66 days + 22 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 57 4a 08 37 33 b7 fc Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- fc 00 08 37 33 b7 fc 00 00:33:31.798 [VENDOR SPECIFIC] fc 00 08 2f 33 b7 fc 00 00:33:25.865 [VENDOR SPECIFIC] fc 00 10 2f 33 b7 fc 00 00:33:20.011 [VENDOR SPECIFIC] fc 00 10 1f 33 b7 fc 00 00:33:19.933 [VENDOR SPECIFIC] fc 00 20 1f 33 b7 fc 00 00:33:14.003 [VENDOR SPECIFIC] Error 3471 occurred at disk power-on lifetime: 1606 hours (66 days + 22 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 57 4a 08 2f 33 b7 fc Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- fc 00 08 2f 33 b7 fc 00 00:33:25.865 [VENDOR SPECIFIC] fc 00 10 2f 33 b7 fc 00 00:33:20.011 [VENDOR SPECIFIC] fc 00 10 1f 33 b7 fc 00 00:33:19.933 [VENDOR SPECIFIC] fc 00 20 1f 33 b7 fc 00 00:33:14.003 [VENDOR SPECIFIC] fc 00 20 ff 32 b7 fc 00 00:33:13.992 [VENDOR SPECIFIC] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.