# Remember to uncomment the options you wish to enable.

# Maximum and minimum number of peers to connect to per torrent.
min_peers = 40
max_peers = 120

# Same as above but for seeding completed torrents (-1 = same as downloading)
min_peers_seed = 20
max_peers_seed = 60

# Maximum number of simultanious uploads per torrent.
max_uploads = 50

# Global upload and download rate in KiB. "0" for unlimited.
download_rate = 0
upload_rate = 0

# Default directory to save the downloaded torrents.
#directory = ./

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = ~/.rtorrent/.session

# Watch a directory for new torrents, and stop those that have been
# deleted.
schedule = watch_Apps,5,5,"load_start=~/torrents/apps/*.torrent,d.set_directory=~/dls/apps/"
schedule = watch_Games,5,5,"load_start=~/torrents/games/*.torrent,d.set_directory=~/dls/games/"
schedule = watch_Movies,5,5,"load_start=~/torrents/movies/*.torrent,d.set_directory=~/dls/movies/"
schedule = watch_Music,5,5,"load_start=~/torrents/music/*.torrent,d.set_directory=~/dls/music/"
schedule = watch_TV,5,5,"load_start=~/torrents/tv/*.torrent,d.set_directory=~/dls/tv/"
schedule = untied_directory,5,5,stop_untied=

# Close torrents when diskspace is low.
schedule = low_diskspace,5,60,close_low_diskspace=7500M

# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_ />
# Enable the default ratio group.
ratio.enable=

# Change the limits if needed, the defaults should be sufficient.
ratio.min.set=1000
ratio.max.set=3000
ratio.upload.set=20M

# Changing the command triggered when the ratio is reached.
system.method.set = group.seeding.ratio.command, d.close=yes, d.erase=yes

# The ip address reported to the tracker.
#ip = 127.0.0.1
#ip = rakshasa.no

# The ip address the listening socket and outgoing connections is
# bound to.
#bind = 127.0.0.1
#bind = rakshasa.no

# Port range to use for listening.
port_range = 56660-56700

# Start opening ports at a random position within the port range.
port_random = yes

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
check_hash = yes

# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = no

# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
encryption = allow_incoming,try_outgoing,enable_retry,require_RC4

# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
dht = disable

# UDP port to use for DHT.
#
# dht_port = 6881

# Enable peer exchange (for torrents not marked private)
#
# peer_exchange = yes

# Color / Canvas patch
done_fg_color = 2
#done_bg_color = 2
active_fg_color = 1
#active_bg_color = 4

#
# Do not modify the following parameters unless you know what you're doing.
#

# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10

# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10