Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ATIIXP: IDE controller at PCI slot 0000:00:14.1
PCI: Guessed IRQ 10 for device 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:01:05.0
PCI: Sharing IRQ 10 with 0000:02:00.0
PCI: Sharing IRQ 10 with 0000:02:04.1
PCI: Sharing IRQ 10 with 0000:02:07.0
ATIIXP: chipset revision 0
ATIIXP: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x8060-0x8067, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0x8068-0x806f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: TOSHIBA MK8025GAS, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: _NEC DVD+/-RW ND-6450A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156301488 sectors (80026 MB), CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
 hda: hda1 hda2 < hda5 >
hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
libata version 2.00 loaded.
usbmon: debugfs is not available
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: No PS/2 controller found. Probing ports directly.
i8042.c: Detected active multiplexing controller, rev 1.1.
serio: i8042 AUX0 port at 0x60,0x64 irq 12
serio: i8042 AUX1 port at 0x60,0x64 irq 12
serio: i8042 AUX2 port at 0x60,0x64 irq 12
serio: i8042 AUX3 port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
md: Autodetecting RAID arrays.
md: autorun ...
Time: acpi_pm clocksource has been installed.
md: ... autorun DONE.
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
input: AT Translated Set 2 keyboard as /class/input/input0
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: journal-1153: found in header: first_unflushed_offset 2793, last_flushed_trans_id 7167
ReiserFS: hda1: journal-1206: Starting replay from offset 30786325580521, trans_id 0
ReiserFS: hda1: journal-1299: Setting newest_mount_id to 33
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 192k freed
Adding 995988k swap on /dev/hda5.  Priority:-1 extents:1 across:995988k
input: PC Speaker as /class/input/input1
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
PCI: Guessed IRQ 11 for device 0000:00:13.0
PCI: Sharing IRQ 11 with 0000:00:13.1
PCI: Sharing IRQ 11 with 0000:02:03.0
PCI: Sharing IRQ 11 with 0000:02:07.2
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:13.0: irq 11, io mem 0xd0001000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ieee1394: Initialized config rom entry `ip1394'
PCI: Guessed IRQ 11 for device 0000:00:13.1
PCI: Sharing IRQ 11 with 0000:00:13.0
PCI: Sharing IRQ 11 with 0000:02:03.0
PCI: Sharing IRQ 11 with 0000:02:07.2
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.1: irq 11, io mem 0xd0002000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
PCI: Guessed IRQ 10 for device 0000:02:07.0
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:01:05.0
PCI: Sharing IRQ 10 with 0000:02:00.0
PCI: Sharing IRQ 10 with 0000:02:04.1
ohci_hcd 0000:02:07.0: OHCI Host Controller
ohci_hcd 0000:02:07.0: new USB bus registered, assigned bus number 3
ohci_hcd 0000:02:07.0: irq 10, io mem 0xd0206000
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
8139too Fast Ethernet driver 0.9.27
bcm43xx driver
PCI: Guessed IRQ 5 for device 0000:02:07.1
PCI: Sharing IRQ 5 with 0000:02:02.0
ohci_hcd 0000:02:07.1: OHCI Host Controller
ohci_hcd 0000:02:07.1: new USB bus registered, assigned bus number 4
ohci_hcd 0000:02:07.1: irq 5, io mem 0xd0207000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected

PCI: IRQ 5 for device 0000:00:14.5 doesn't match PIRQ mask - try pci=usepirqmask
<6>usb 3-1: new low speed USB device using ohci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:02:07.0-1
usb 4-1: new full speed USB device using ohci_hcd and address 2
PCI: Guessed IRQ 10 for device 0000:02:00.0
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:01:05.0
PCI: Sharing IRQ 10 with 0000:02:04.1
PCI: Sharing IRQ 10 with 0000:02:07.0
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10]  MMIO=[d0208000-d02087ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
Yenta: CardBus bridge found at 0000:02:04.0 [103c:006b]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.0, mfunc 0x01111d22, devctl 0x64
usb 4-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Yenta: ISA IRQ mask 0x00d8, PCI irq 10
Socket status: 30000086
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
Yenta: CardBus bridge found at 0000:02:04.1 [103c:006b]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:04.1, mfunc 0x01111d22, devctl 0x64
Yenta: ISA IRQ mask 0x00d8, PCI irq 10
Socket status: 30000006
Yenta: Raising subordinate bus# of parent bus (#02) from #04 to #07
pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
cs: IO port probe 0xa000-0xafff: clean.
pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff
pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
PCI: Guessed IRQ 11 for device 0000:02:03.0
PCI: Sharing IRQ 11 with 0000:00:13.0
PCI: Sharing IRQ 11 with 0000:00:13.1
PCI: Sharing IRQ 11 with 0000:02:07.2
eth0: RealTek RTL8139 at 0xa000, 00:0f:b0:3e:4f:df, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8101'
PCI: Guessed IRQ 5 for device 0000:02:02.0
PCI: Sharing IRQ 5 with 0000:02:07.1
bcm43xx: Chip ID 0x4306, rev 0x3
bcm43xx: Number of cores: 5
bcm43xx: Core 0: ID 0x800, rev 0x4, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x5, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x80d, rev 0x2, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x807, rev 0x2, vendor 0x4243, disabled
bcm43xx: Core 4: ID 0x804, rev 0x9, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 2, Type 2, Revision 2
bcm43xx: Detected Radio: ID: 2205017f (Manuf: 17f Ver: 2050 Rev: 2)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
PCI: Guessed IRQ 11 for device 0000:02:07.2
PCI: Sharing IRQ 11 with 0000:00:13.0
PCI: Sharing IRQ 11 with 0000:00:13.1
PCI: Sharing IRQ 11 with 0000:02:03.0
ehci_hcd 0000:02:07.2: EHCI Host Controller
ehci_hcd 0000:02:07.2: new USB bus registered, assigned bus number 5
ehci_hcd 0000:02:07.2: irq 11, io mem 0xd0208c00
ehci_hcd 0000:02:07.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 5 ports detected
usb 3-1: USB disconnect, address 2
usb 5-2: new high speed USB device using ehci_hcd and address 3
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[4a3f020079694058]
usb 5-2: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb 4-1: USB disconnect, address 2
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: excluding 0x200-0x20f 0x378-0x37f
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcd7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0x800-0x80f: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7
cs: IO port probe 0x100-0x3af: excluding 0x200-0x20f 0x378-0x37f
cs: IO port probe 0xa00-0xaff: clean.
ohci_hcd 0000:02:07.0: wakeup
usb 3-1: new low speed USB device using ohci_hcd and address 3
usb 3-1: configuration #1 chosen from 1 choice
input: Logitech USB-PS/2 Optical Mouse as /class/input/input3
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:02:07.0-1
parport0: PC-style at 0x378 [PCSPP,EPP]
lp0: using parport0 (polling).
lp0: console ready
Capability LSM initialized
input: PS/2 Generic Mouse as /class/input/input4
  Vendor: HITACHI_  Model: DK23FA-40         Rev:  0 0
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
 sda: sda1 sda2 < sda5 >
sd 1:0:0:0: Attached scsi disk sda
usb-storage: device scan complete
sd 1:0:0:0: Attached scsi generic sg0 type 0
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
spurious 8259A interrupt: IRQ7.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth1: link is not ready
IPv6 over IPv4 tunneling driver
[drm] Initialized drm 1.0.1 20051102
PCI: Guessed IRQ 10 for device 0000:01:05.0
PCI: Sharing IRQ 10 with 0000:00:14.1
PCI: Sharing IRQ 10 with 0000:02:00.0
PCI: Sharing IRQ 10 with 0000:02:04.1
PCI: Sharing IRQ 10 with 0000:02:07.0
[drm] Initialized radeon 1.25.0 20060524 on minor 0
mtrr: 0xe0000000,0x10000000 overlaps existing 0xe0000000,0x8000000
agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V3 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V3 device at 0000:01:05.0 into 4x mode
[drm] Setting GART location based on old memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: no IPv6 routers present
usb 5-2: USB disconnect, address 3
usb 5-3: new high speed USB device using ehci_hcd and address 4
usb 5-3: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
  Vendor: HITACHI_  Model: DK23FA-40         Rev:  0 0
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
 sda: sda1 sda2 < sda5 >
sd 2:0:0:0: Attached scsi disk sda
sd 2:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
hdc: irq timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdc: DMA disabled
hdc: ATAPI reset complete
hdc: irq timeout: status=0xd0 { Busy }
ide: failed opcode was: unknown
hdc: ATAPI reset complete
usb 5-3: USB disconnect, address 4
usb 5-3: new high speed USB device using ehci_hcd and address 5
usb 5-3: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
  Vendor: HITACHI_  Model: DK23FA-40         Rev:  0 0
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
 sda: sda1 sda2 < sda5 >
sd 3:0:0:0: Attached scsi disk sda
sd 3:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
ReiserFS: sda1: found reiserfs format "3.6" with standard journal
ReiserFS: sda1: warning: CONFIG_REISERFS_CHECK is set ON
ReiserFS: sda1: warning: - it is slow mode for debugging.
ReiserFS: sda1: using ordered data mode
ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sda1: checking transaction log (sda1)
ReiserFS: sda1: journal-1153: found in header: first_unflushed_offset 1279, last_flushed_trans_id 373387
ReiserFS: sda1: journal-1206: Starting replay from offset 1603689248720127, trans_id 0
ReiserFS: sda1: journal-1299: Setting newest_mount_id to 302
ReiserFS: sda1: Using r5 hash to sort names
usb 5-3: USB disconnect, address 5
usb 5-3: new high speed USB device using ehci_hcd and address 6
usb 5-3: configuration #1 chosen from 1 choice
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
  Vendor: HITACHI_  Model: DK23FA-40         Rev:  0 0
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 78140160 512-byte hdwr sectors (40008 MB)
sda: Write Protect is off
sda: Mode Sense: 33 00 00 00
sda: assuming drive cache: write through
 sda: sda1 sda2 < sda5 >
sd 4:0:0:0: Attached scsi disk sda
sd 4:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete