home# smartctl -a /dev/ad0 smartctl 5.40 2010-10-16 r3189 [FreeBSD 7.0-RELEASE i386] (local build) Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Fujitsu MPA..MPG series Device Model: FUJITSU MPG3204AT E Serial Number: VH73T0B00GDE Firmware Version: 80B5 User Capacity: 20,495,154,688 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 5 ATA Standard is: ATA/ATAPI-5 T13 1321D revision 1 Local Time is: Fri May 20 19:14:48 2011 YEKST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED See vendor-specific Attribute list for marginal Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 240) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0002) Does not save SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 001 032 Pre-fail Always In_the_past 4505 2 Throughput_Performance 0x0005 100 100 020 Pre-fail Offline - 0 3 Spin_Up_Time 0x0007 094 090 025 Pre-fail Always - 2 4 Start_Stop_Count 0x0012 096 096 016 Old_age Always - 2503 5 Reallocated_Sector_Ct 0x0033 064 064 024 Pre-fail Always - 345 7 Seek_Error_Rate 0x000b 100 100 020 Pre-fail Always - 1722 8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0 9 Power_On_Seconds 0x0012 075 075 020 Old_age Always - 3879h+48m+12s 10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 083 083 020 Old_age Always - 2623 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 32 196 Reallocated_Event_Count 0x0033 064 064 024 Pre-fail Always - 248 197 Current_Pending_Sector 0x0010 100 030 020 Old_age Offline - 0 198 Offline_Uncorrectable 0x0010 053 053 020 Old_age Offline - 95 199 UDMA_CRC_Error_Count 0x000a 200 200 197 Old_age Always - 37 200 Multi_Zone_Error_Rate 0x000b 100 001 020 Pre-fail Always In_the_past 467 SMART Error Log Version: 1 ATA Error Count: 728 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 728 occurred at disk power-on lifetime: 3880 hours (161 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 71 00 db 24 71 e1 Device Fault; Error: IDNF at LBA = 0x017124db = 24192219 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 20 bf 37 6f e1 00 03:06:26.500 WRITE DMA Error 727 occurred at disk power-on lifetime: 3880 hours (161 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 71 18 4f 29 04 e0 Device Fault; Error: IDNF 24 sectors at LBA = 0x0004294f = 272719 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 18 4f 29 04 e0 00 03:04:00.700 READ DMA Error 726 occurred at disk power-on lifetime: 3880 hours (161 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 71 80 3f 31 5c e2 Device Fault; Error: IDNF 128 sectors at LBA = 0x025c313f = 39596351 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 80 3f 31 5c e2 00 03:03:01.900 READ DMA Error 725 occurred at disk power-on lifetime: 3880 hours (161 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 71 04 d3 2c 0c e0 Device Fault; Error: IDNF 4 sectors at LBA = 0x000c2cd3 = 797907 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 04 d3 2c 0c e0 00 03:02:59.000 READ DMA Error 724 occurred at disk power-on lifetime: 3880 hours (161 days + 16 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 10 71 04 5b fb 6f e1 Device Fault; Error: IDNF 4 sectors at LBA = 0x016ffb5b = 24116059 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 04 5b fb 6f e1 00 03:02:58.500 READ DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging home#