Linux version 2.6.18-gentoo-r3 (root@localhost) (version gcc 4.1.1 (Gentoo 4.1.1-r1)) #1 SMP Wed Nov 29 19:32:57 CET 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 126960 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 VIA694                                ) @ 0x000f67c0
ACPI: RSDT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 VIA694 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: DSDT (v001 VIA694 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
Detected 1214.540 MHz processor.
Built 1 zonelists.  Total pages: 131056
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 video=vesafb:ywrap,mtrr,1024x768@70 splash=verbose,theme:emergence quiet CONSOLE=/dev/tty1 udev
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0140a000)
Enabling fast FPU save and restore... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c047b000 soft=c0473000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 513648k/524224k available (2477k kernel code, 9960k reserved, 806k data, 208k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2431.25 BogoMIPS (lpj=4862507)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: Core revision 20060707
ACPI: setting ELCR to 0200 (from 0a20)
CPU0: AMD Athlon(tm) processor stepping 02
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 1563k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb260, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:01.0
  IO window: disabled.
  MEM window: e4000000-e6ffffff
  PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1164830880.800:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.1 (2006/08/19) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
vesafb: unrecognized option mtrr
vesafb: NVIDIA Corporation, nv44 Board - p362h0  , Chip Rev    (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:d240
vesafb: pmi: set display start = c00cd276, set palette = c00cd2e0
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: VBIOS/hardware supports DDC2 transfers
vesafb: monitor limits: vf = 120 Hz, hf = 70 kHz, clk = 110 MHz
vesafb: scrolling: ywrap using protected mode interface, yres_virtual=24576
Console: switching to colour frame buffer device 128x48
fbsplash: console 0 using theme 'emergence'
vesafb: framebuffer at 0xd0000000, mapped to 0xe0880000, using 24576k, total 262144k
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
input: ImExPS/2 Generic Explorer Mouse as /class/input/input1
hda: WDC WD200BB-00CLB0, ATA DISK drive
hdb: Maxtor 6Y120P0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive
hdd: MATSHITA CR-585, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63, UDMA(100)
hda: cache flushes not supported
 hda: hda1 hda2 hda3
hdb: max request size: 128KiB
hdb: 240121728 sectors (122942 MB) w/7936KiB Cache, CHS=65535/16/63, UDMA(100)
hdb: cache flushes supported
 hdb: hdb2
hdc: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 24X CD-ROM drive, 128kB Cache, DMA
SCSI Media Changer driver v0.25 
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:08.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ehci_hcd 0000:00:08.2: EHCI Host Controller
ehci_hcd 0000:00:08.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:08.2: irq 11, io mem 0xe8002000
ehci_hcd 0000:00:08.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:08.0: UHCI Host Controller
uhci_hcd 0000:00:08.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:08.0: irq 5, io base 0x0000c000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:08.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:08.1: UHCI Host Controller
uhci_hcd 0000:00:08.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:08.1: irq 11, io base 0x0000c400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:11.2: UHCI Host Controller
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:11.2: irq 11, io base 0x0000d400
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:11.3: UHCI Host Controller
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:11.3: irq 11, io base 0x0000d800
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:11.4[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:11.4: UHCI Host Controller
uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:11.4: irq 11, io base 0x0000dc00
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usb 3-2: new full speed USB device using uhci_hcd and address 3
usb 3-2: configuration #1 chosen from 1 choice
usb 4-1: new full speed USB device using uhci_hcd and address 2
usb 4-1: configuration #1 chosen from 1 choice
usb 4-2: new full speed USB device using uhci_hcd and address 3
usb 4-2: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 3 vid 0x03F0 pid 0x0011
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 208k freed
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11]  MMIO=[e8003000-e80037ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
JFS: nTxBlock = 4028, nTxLock = 32229
Intel(R) PRO/1000 Network Driver - version 7.1.9-k4
Copyright (c) 1999-2006 Intel Corporation.
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0000000000000258]
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
  Vendor:           Model:                   Rev:     
  Type:   Direct-Access                      ANSI SCSI revision: 00
SCSI device sda: 2043617 512-byte hdwr sectors (1046 MB)
sda: Write Protect is off
sda: Mode Sense: 00 c0 00 00
sda: assuming drive cache: write through
SCSI device sda: 2043617 512-byte hdwr sectors (1046 MB)
sda: Write Protect is off
sda: Mode Sense: 00 c0 00 00
sda: assuming drive cache: write through
 sda: unknown partition table
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
kjournald starting.  Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
NVRM: loading NVIDIA Linux x86 Kernel Module  1.0-9629  Wed Nov  1 19:30:07 PST 2006
input: PC Speaker as /class/input/input2
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
tulip0:  MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth0: Lite-On 82c168 PNIC rev 32 at e239e000, 00:A0:CC:D5:A8:71, IRQ 11.
via82xx: Assuming DXS channels with 48k fixed sample rate.
         Please try dxs_support=5 option
         and report if it works on your machine.
         For more details, read ALSA-Configuration.txt.
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:11.5 to 64
input: Wacom Graphire3 6x8 as /class/input/input3
usbcore: registered new driver wacom
drivers/usb/input/wacom.c: v1.45:USB Wacom Graphire and Wacom Intuos tablet driver
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
gameport: NS558 PnP Gameport is pnp00:0e/gameport0, io 0x201, speed 962kHz
EXT3 FS on hda3, internal journal
Adding 1028152k swap on /dev/hda2.  Priority:-1 extents:1 across:1028152k
Real Time Clock Driver v1.12ac
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30560580, sector=30560557
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30560557
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30560580, sector=30560565
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30560565
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30560580, sector=30560573
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30560573
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30560584, sector=30560581
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30560581
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31070151, sector=31070141
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31070141
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31070151, sector=31070149
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31070149
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31070158, sector=31070157
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31070157
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31070168, sector=31070165
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31070165
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30904606, sector=30904605
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30904605
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30904615, sector=30904613
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30904613
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30904606, sector=30904605
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30904605
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30904606, sector=30904605
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30904605
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=30904606, sector=30904605
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 30904605
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31002820, sector=31002813
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31002813
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31002823, sector=31002821
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31002821
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31002834, sector=31002829
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31002829
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31002820, sector=31002813
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31002813
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31002820, sector=31002813
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31002813
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31002820, sector=31002813
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31002813
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297822, sector=31297813
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297813
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297822, sector=31297821
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297821
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297829, sector=31297829
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297829
hda: dma_intr: status=0x53 { DriveReady SeekComplete Index Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297822, sector=31297821
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297821
hda: dma_intr: status=0x53 { DriveReady SeekComplete Index Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297822, sector=31297821
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297821
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297822, sector=31297821
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297821
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297822, sector=31297821
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297821
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31105249, sector=31105245
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31105245
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31105249, sector=31105245
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31105245
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31105249, sector=31105245
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31105245
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31105249, sector=31105245
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31105245
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297839, sector=31297837
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297837
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297857, sector=31297845
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297845
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297857, sector=31297853
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297853
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297839, sector=31297837
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297837
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297839, sector=31297837
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297837
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31297839, sector=31297837
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31297837
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31133902, sector=31133901
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31133901
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31133902, sector=31133901
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31133901
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=31133902, sector=31133901
ide: failed opcode was: unknown
end_request: I/O error, dev hda, sector 31133901
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode