Linux version 2.6.18-dcc-smp (root@XANQZ3Q8Y10) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 SMP PREEMPT Mon Dec 4 11:02:33 EST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 0000000000100000 - 000000004fea6000 (usable) BIOS-e820: 000000004fea6000 - 0000000050000000 (reserved) BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved) BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 382MB HIGHMEM available. 896MB LOWMEM available. On node 0 totalpages: 327334 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 97958 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000fdf00 ACPI: RSDT (v001 DELL CPi R 0x27d5061c ASL 0x00000061) @ 0x4fef0000 ACPI: FADT (v001 DELL CPi R 0x27d5061c ASL 0x00000061) @ 0x4fef0400 ACPI: ASF! (v016 DELL CPi R 0x27d5061c ASL 0x00000061) @ 0x4fef0800 ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 Allocating PCI resources starting at 60000000 (gap: 50000000:aec10000) Detected 1398.854 MHz processor. Built 1 zonelists. Total pages: 327334 Kernel command line: auto BOOT_IMAGE=Xandros_4 ro root=302 quiet rw acpi=on resume2=swap:/dev/hda1 Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01a0f000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1293664k/1309336k available (1791k kernel code, 14512k reserved, 755k data, 220k init, 391832k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2799.54 BogoMIPS (lpj=5599099) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 1024K CPU: After all inits, caps: a7e9f9bf 00000000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 12k freed checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 307k freed ACPI: Core revision 20060707 ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. ACPI: setting ELCR to 0200 (from 0800) CPU0: Intel(R) Pentium(R) M processor 1400MHz stepping 05 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs migration_cost=0 PM: Adding info for No Bus:platform NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfc96e, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing PM: Adding info for acpi:acpi ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PM: Adding info for No Bus:pci0000:00 ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:00:02.0 PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH4 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 PCI: Bus #02 (-#05) is hidden behind transparent bridge #01 (-#01) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently PCI: Bus #06 (-#09) is hidden behind transparent bridge #01 (-#01) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] PM: Adding info for pci:0000:00:00.0 PM: Adding info for pci:0000:00:00.1 PM: Adding info for pci:0000:00:00.3 PM: Adding info for pci:0000:00:02.0 PM: Adding info for pci:0000:00:02.1 PM: Adding info for pci:0000:00:1d.0 PM: Adding info for pci:0000:00:1d.1 PM: Adding info for pci:0000:00:1d.2 PM: Adding info for pci:0000:00:1d.7 PM: Adding info for pci:0000:00:1e.0 PM: Adding info for pci:0000:00:1f.0 PM: Adding info for pci:0000:00:1f.1 PM: Adding info for pci:0000:00:1f.5 PM: Adding info for pci:0000:01:00.0 PM: Adding info for pci:0000:01:01.0 PM: Adding info for pci:0000:01:01.1 PM: Adding info for pci:0000:01:01.2 PM: Adding info for pci:0000:01:01.3 PM: Adding info for pci:0000:01:03.0 ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11 ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init PM: Adding info for No Bus:pnp0 PM: Adding info for pnp:00:00 PM: Adding info for pnp:00:01 PM: Adding info for pnp:00:02 PM: Adding info for pnp:00:03 PM: Adding info for pnp:00:04 PM: Adding info for pnp:00:05 PM: Adding info for pnp:00:06 PM: Adding info for pnp:00:07 PM: Adding info for pnp:00:08 PM: Adding info for pnp:00:09 PM: Adding info for pnp:00:0a PM: Adding info for pnp:00:0b PM: Adding info for pnp:00:0c PM: Adding info for pnp:00:0d PM: Adding info for pnp:00:0e pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:02: ioport range 0x800-0x805 could not be reserved pnp: 00:02: ioport range 0x808-0x80f could not be reserved pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved pnp: 00:03: ioport range 0x806-0x807 has been reserved pnp: 00:03: ioport range 0x810-0x85f could not be reserved pnp: 00:03: ioport range 0x860-0x87f has been reserved pnp: 00:03: ioport range 0x880-0x8bf has been reserved pnp: 00:03: ioport range 0x8c0-0x8df has been reserved pnp: 00:08: ioport range 0x900-0x97f has been reserved pnp: 00:0e: ioport range 0x7b0-0x7bb has been reserved pnp: 00:0e: ioport range 0x7c0-0x7df has been reserved pnp: 00:0e: ioport range 0xbb0-0xbbb has been reserved pnp: 00:0e: ioport range 0xbc0-0xbdf has been reserved pnp: 00:0e: ioport range 0xfb0-0xfbb has been reserved pnp: 00:0e: ioport range 0xfc0-0xfdf has been reserved pnp: 00:0e: ioport range 0x13b0-0x13bb has been reserved pnp: 00:0e: ioport range 0x13c0-0x13df has been reserved PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Bus 2, cardbus bridge: 0000:01:01.0 IO window: 0000e000-0000e0ff IO window: 0000e400-0000e4ff PREFETCH window: 60000000-61ffffff MEM window: 66000000-67ffffff PCI: Bus 6, cardbus bridge: 0000:01:01.1 IO window: 0000e800-0000e8ff IO window: 00001000-000010ff PREFETCH window: 62000000-63ffffff MEM window: 68000000-69ffffff PCI: Bridge: 0000:00:1e.0 IO window: e000-efff MEM window: fc000000-fdffffff PREFETCH window: 60000000-64ffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:01:01.0 (0000 -> 0003) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:01:01.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt 0000:01:01.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered PM: Adding info for platform:pcspkr audit: initializing netlink socket (disabled) audit(1165352026.668:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API io scheduler noop registered io scheduler deadline registered (default) PM: Adding info for platform:vesafb.0 PM: Adding info for No Bus:pnp1 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac PM: Adding info for No Bus:isa RAMDISK driver initialized: 16 RAM disks of 131072K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 PM: Adding info for platform:i8042 serio: i8042 AUX port at 0x60,0x64 irq 12 PM: Adding info for serio:serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 PM: Adding info for serio:serio1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 Using IPI No-Shortcut mode Suspend2 Core. Suspend2 Userspace UI Support module loaded. Suspend2 Checksumming module loaded. Suspend2 Userspace Storage Manager module loaded. Suspend2 Compressor module loaded. Suspend2 Encryptor module loaded. Suspend2 Block I/O module loaded. Suspend2 Swap Allocator module loaded. ACPI: (supports S0 S1 S3 S4 S5) RAMDISK: Compressed image found at block 0 Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input0 VFS: Mounted root (ext2 filesystem). SCSI subsystem initialized ICH4: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 ICH4: chipset revision 1 ICH4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xbfa0-0xbfa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xbfa8-0xbfaf, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: TOSHIBA MK8032GAX, ATA DISK drive PM: Adding info for No Bus:ide0 ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 PM: Adding info for ide:0.0 Probing IDE interface ide1... hda: max request size: 512KiB hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 Suspend2 2.2.8.5: SwapAllocator: Signature found. Suspend2 2.2.8.5: Resuming enabled. Suspend2 2.2.8.5: Normal swapspace found. Suspend2 2.2.8.5: No image found. ReiserFS: hda2: found reiserfs format "3.6" with standard journal ReiserFS: hda2: using ordered data mode ReiserFS: hda2: journal params: device hda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda2: checking transaction log (hda2) ReiserFS: hda2: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem). Trying to move old root to /initrd ... okay Freeing unused kernel memory: 220k freed Adding 1048568k swap on /dev/hda1. Priority:-1 extents:1 across:1048568k device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled PM: Adding info for platform:serial8250 serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 NET: Registered protocol family 24 parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,EPP] lp0: using parport0 (interrupt-driven). lp0: console ready fuse init (API version 7.7) ACPI: Battery Slot [BAT0] (battery present) input: PS/2 Mouse as /class/input/input1 input: AlpsPS/2 ALPS GlidePoint as /class/input/input2 ts: Compaq touchscreen protocol output Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 855 Chipset. agpgart: Detected 892K stolen memory. agpgart: AGP aperture is 128M @ 0xf0000000 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 intel_rng: FWH not detected ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 55482 usecs intel8x0: clocking to 48000 PM: Adding info for ac97:0-0:STAC9750,51 tg3.c:v3.65 (August 07, 2006) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 eth0: Tigon3 [partno(BCM95705A50) rev 3001 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:0b:db:5b:88:bc eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[763f0000] dma_mask[64-bit] Yenta: CardBus bridge found at 0000:01:01.0 [1028:0139] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:01:01.0, mfunc 0x012c1202, devctl 0x64 Yenta: ISA IRQ mask 0x0458, PCI irq 11 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#01) from #01 to #05 pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff cs: IO port probe 0xe000-0xefff: clean. pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x64ffffff Yenta: CardBus bridge found at 0000:01:01.1 [1028:0139] PM: Writing back config space on device 0000:01:00.0 at offset b (was 165d14e4, writing 865d1028) PM: Writing back config space on device 0000:01:00.0 at offset 3 (was 0, writing 2008) PM: Writing back config space on device 0000:01:00.0 at offset 2 (was 2000000, writing 2000001) PM: Writing back config space on device 0000:01:00.0 at offset 1 (was 2b00000, writing 2b00106) Yenta: ISA IRQ mask 0x0458, PCI irq 11 Socket status: 30000047 Yenta: Raising subordinate bus# of parent bus (#01) from #05 to #09 pcmcia: parent PCI bridge I/O window: 0xe000 - 0xefff cs: IO port probe 0xe000-0xefff: clean. pcmcia: parent PCI bridge Memory window: 0xfc000000 - 0xfdffffff pcmcia: parent PCI bridge Memory window: 0x60000000 - 0x64ffffff ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt 0000:01:01.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PM: Adding info for ieee1394:fw-host0 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[fcfef800-fcfeffff] Max Packet=[2048] IR/IT contexts=[4/8] BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 3713.000 MB/sec raid5: using function: pIII_sse (3713.000 MB/sec) raid6: int32x1 497 MB/s raid6: int32x2 630 MB/s raid6: int32x4 459 MB/s raid6: int32x8 401 MB/s raid6: mmxx1 1636 MB/s PM: Adding info for ieee1394:394fc0001274a061 ieee1394: Host added: ID:BUS[0-00:1023] GUID[394fc0001274a061] PM: Adding info for ieee1394:394fc0001274a061-0 raid6: mmxx2 1860 MB/s raid6: sse1x1 1067 MB/s raid6: sse1x2 1913 MB/s raid6: sse2x1 1960 MB/s raid6: sse2x2 1896 MB/s raid6: using algorithm sse2x1 (1960 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: raid10 personality registered for level 10 tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names ide-floppy driver 0.99.newide floppy0: no floppy controllers found ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names pcmcia: Detected deprecated PCMCIA ioctl usage from process: cardmgr. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: IO port probe 0x100-0x4ff: excluding 0x170-0x177 0x280-0x287 0x370-0x37f cs: IO port probe 0x100-0x4ff: excluding 0x170-0x177 0x280-0x287 0x370-0x37f cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0xa00-0xaff: clean. cs: IO port probe 0xa00-0xaff: clean. usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80 PM: Adding info for usb:usb1 PM: Adding info for No Bus:usbdev1.1_ep00 usb usb1: configuration #1 chosen from 1 choice PM: Adding info for usb:1-0:1.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev1.1_ep81 ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40 PM: Adding info for usb:usb2 PM: Adding info for No Bus:usbdev2.1_ep00 usb usb2: configuration #1 chosen from 1 choice PM: Adding info for usb:2-0:1.0 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev2.1_ep81 ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20 PM: Adding info for usb:usb3 PM: Adding info for No Bus:usbdev3.1_ep00 usb usb3: configuration #1 chosen from 1 choice PM: Adding info for usb:3-0:1.0 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PM: Adding info for No Bus:usbdev3.1_ep81 ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 11, io mem 0xfaeffc00 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 PM: Adding info for usb:usb4 PM: Adding info for No Bus:usbdev4.1_ep00 usb usb4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-0:1.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected PM: Adding info for No Bus:usbdev4.1_ep81 NET: Registered protocol family 17 Using specific hotkey driver ACPI: AC Adapter [AC] (on-line) ACPI: ACPI Dock Station Driver ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THM] (52 C) Time: acpi_pm clocksource has been installed. ACPI: Lid Switch [LID] ACPI: Power Button (CM) [PBTN] ACPI: Sleep Button (CM) [SBTN] ibm_acpi: ec object not found ACPI: Video Device [VID] (multi-head: yes rom: no post: no) ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 208 bytes per conntrack usbcore: registered new driver wacom wacom: v1.45:USB Wacom Graphire and Wacom Intuos tablet driver BIOS EDD facility v0.16 2004-Jun-25, 1 devices found usb 4-4: new high speed USB device using ehci_hcd and address 2 PM: Adding info for usb:4-4 PM: Adding info for No Bus:usbdev4.2_ep00 usb 4-4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-4:1.0 PM: Adding info for No Bus:usbdev4.2_ep01 PM: Adding info for No Bus:usbdev4.2_ep82 PM: Adding info for No Bus:usbdev4.2_ep83 PM: Adding info for No Bus:usbdev4.2_ep04 usb 4-4: USB disconnect, address 2 PM: Removing info for No Bus:usbdev4.2_ep01 PM: Removing info for No Bus:usbdev4.2_ep82 PM: Removing info for No Bus:usbdev4.2_ep83 PM: Removing info for No Bus:usbdev4.2_ep04 PM: Removing info for usb:4-4:1.0 PM: Removing info for No Bus:usbdev4.2_ep00 PM: Removing info for usb:4-4 usb 4-4: new high speed USB device using ehci_hcd and address 3 PM: Adding info for usb:4-4 PM: Adding info for No Bus:usbdev4.3_ep00 usb 4-4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-4:1.0 PM: Adding info for No Bus:usbdev4.3_ep01 PM: Adding info for No Bus:usbdev4.3_ep82 PM: Adding info for No Bus:usbdev4.3_ep83 PM: Adding info for No Bus:usbdev4.3_ep04 usb 4-4: USB disconnect, address 3 PM: Removing info for No Bus:usbdev4.3_ep01 PM: Removing info for No Bus:usbdev4.3_ep82 PM: Removing info for No Bus:usbdev4.3_ep83 PM: Removing info for No Bus:usbdev4.3_ep04 PM: Removing info for usb:4-4:1.0 PM: Removing info for No Bus:usbdev4.3_ep00 PM: Removing info for usb:4-4 ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation usb_init() usbcore: registered new driver zd1211rw zd1211rw initialized usb 4-4: new high speed USB device using ehci_hcd and address 4 PM: Adding info for usb:4-4 PM: Adding info for No Bus:usbdev4.4_ep00 usb 4-4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-4:1.0 PM: Adding info for No Bus:usbdev4.4_ep01 PM: Adding info for No Bus:usbdev4.4_ep82 PM: Adding info for No Bus:usbdev4.4_ep83 PM: Adding info for No Bus:usbdev4.4_ep04 usb 4-4: USB disconnect, address 4 PM: Removing info for No Bus:usbdev4.4_ep01 PM: Removing info for No Bus:usbdev4.4_ep82 PM: Removing info for No Bus:usbdev4.4_ep83 PM: Removing info for No Bus:usbdev4.4_ep04 PM: Removing info for usb:4-4:1.0 PM: Removing info for No Bus:usbdev4.4_ep00 PM: Removing info for usb:4-4 usb 4-4: new high speed USB device using ehci_hcd and address 5 PM: Adding info for usb:4-4 PM: Adding info for No Bus:usbdev4.5_ep00 usb 4-4: configuration #1 chosen from 1 choice PM: Adding info for usb:4-4:1.0 PM: Adding info for No Bus:usbdev4.5_ep01 PM: Adding info for No Bus:usbdev4.5_ep82 PM: Adding info for No Bus:usbdev4.5_ep83 PM: Adding info for No Bus:usbdev4.5_ep04 set@nokia6110:~$