lack@darkstar:~$ dmesg specific routine.. 3157.45 BogoMIPS (lpj=6314903) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383fbff c1cbfbff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0383fbff c1cbfbff 00000000 00000420 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Sempron(tm) 2300+ stepping 01 Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 0k freed ACPI: setting ELCR to 0200 (from 0e28) NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfa310, last bus=1 Setting up standard PCI resources ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 4000-407f claimed by vt8235 PM PCI quirk: region 5000-500f claimed by vt8235 SMB Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 10 *11 12) ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 6 7 10 11 12) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 *10 11 12) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *5 ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled. ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled. ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled. ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled. ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: e0000000-e1ffffff PREFETCH window: d8000000-dfffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 8192 bind 4096) TCP reno registered apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NTFS driver 2.1.27 [Flags: R/W]. JFS: nTxBlock = 1971, nTxLock = 15772 SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xd8000000, mapped to 0xd0980000, using 1536k, total 65536k vesafb: mode is 1024x768x8, linelength=1024, pages=3 vesafb: protected mode interface info at c000:e4e0 vesafb: scrolling: redraw vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Compaq SMART2 Driver (v 2.6.0) HP CISS Driver (v 2.6.10) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:11.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: VIA IRQ fixup for 0000:00:11.1, from 255 to 11 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1 ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:pio, hdd:DMA Probing IDE interface ide0... hda: SAMSUNG SP0411N, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdd: TSSTcorpCD-R/RW SH-R522C, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: Host Protected Area detected. current capacity is 78240863 sectors (40059 MB) native capacity is 78242976 sectors (40060 MB) hda: Host Protected Area disabled. hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... Adaptec aacraid driver (1.1-5[2409]-mh1) scsi: Detection failed (no card) sym53c416.c: Version 1.0.0-ac qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.1.6 Copyright(c) 2004-2006 Emulex. All rights reserved. Failed initialization of WD-7000 SCSI card! megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005) megaraid: 2.20.4.8 (Release Date: Mon Apr 11 12:27:22 EST 2006) megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006 GDT-HA: Storage RAID Controller Driver. Version: 3.04 GDT-HA: Found 0 PCI Storage RAID Controllers 3ware Storage Controller device driver for Linux v1.26.02.001. 3ware 9000 Storage Controller device driver for Linux v2.26.02.007. nsp32: loading... ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29, 2006) libata version 1.20 loaded. st: Version 20050830, fixed bufsize 32768, s/g segs 256 I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Bus Adapter OSM v1.317 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 Fusion MPT base driver 3.03.09 Copyright (c) 1999-2005 LSI Logic Corporation Fusion MPT SPI Host driver 3.03.09 Fusion MPT FC Host driver 3.03.09 Fusion MPT SAS Host driver 3.03.09 ieee1394: Initialized config rom entry `ip1394' ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance usbmon: debugfs is not available ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:10.3[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 ehci_hcd 0000:00:10.3: EHCI Host Controller ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.3: irq 10, io mem 0xe2012000 ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected 116x: driver isp116x-hcd, 03 Nov 2005 ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 11, io base 0x0000d400 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 3 PCI: setting IRQ 3 as level-triggered ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LNKB] -> GSI 3 (level, low) -> IRQ 3 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 3, io base 0x0000d800 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 10, io base 0x0000dc00 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected sl811: driver sl811-hcd, 19 May 2005 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 3681.000 MB/sec raid5: using function: pIII_sse (3681.000 MB/sec) raid6: int32x1 643 MB/s raid6: int32x2 825 MB/s raid6: int32x4 489 MB/s raid6: int32x8 451 MB/s raid6: mmxx1 1300 MB/s raid6: mmxx2 2289 MB/s raid6: sse1x1 1221 MB/s raid6: sse1x2 2061 MB/s raid6: using algorithm sse1x2 (2061 MB/s) md: raid6 personality registered for level 6 md: multipath personality registered for level -4 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI wakeup devices: PCI0 USB0 USB1 USB2 USB6 USB7 USB8 USB9 LAN0 UAR1 LPT1 ACPI: (supports S0 S1 S4 S5) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. input: AT Translated Set 2 keyboard as /class/input/input0 ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 284k freed Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k USB Universal Host Controller Interface driver v3.0 kmem_cache_create: duplicate cache uhci_urb_priv kmem_cache_create+0x30f/0x3b0 uhci_hcd_init+0x33/0x92 [uhci_hcd] sys_init_module+0xe2/0x160 syscall_call+0x7/0xb Linux agpgart interface v0.101 (c) Dave Jones via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 eth0: VIA Rhine II at 0xe2013000, 00:20:ed:17:f9:d4, IRQ 11. eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000. agpgart: Detected VIA KM400/KM400A chipset agpgart: AGP aperture is 128M @ 0xd0000000 i2c_core: exports duplicate symbol i2c_register_driver (owned by kernel) ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10 USB Universal Host Controller Interface driver v3.0 kmem_cache_create: duplicate cache uhci_urb_priv kmem_cache_create+0x30f/0x3b0 uhci_hcd_init+0x33/0x92 [uhci_hcd] sys_init_module+0xe2/0x160 syscall_call+0x7/0xb USB Universal Host Controller Interface driver v3.0 kmem_cache_create: duplicate cache uhci_urb_priv kmem_cache_create+0x30f/0x3b0 uhci_hcd_init+0x33/0x92 [uhci_hcd] sys_init_module+0xe2/0x160 syscall_call+0x7/0xb never read ISV3 and ISV4 from AC'97 ACPI: PCI interrupt for device 0000:00:0b.0 disabled CS4281: probe of 0000:00:0b.0 failed with error -5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 input: PC Speaker as /class/input/input1 input: PS/2 Generic Mouse as /class/input/input2 parport0: PC-style at 0x378 [PCSPP,TRISTATE] lp0: using parport0 (polling). lp0: console ready Capability LSM initialized USB Universal Host Controller Interface driver v3.0 kmem_cache_create: duplicate cache uhci_urb_priv kmem_cache_create+0x30f/0x3b0 uhci_hcd_init+0x33/0x92 [uhci_hcd] sys_init_module+0xe2/0x160 syscall_call+0x7/0xb USB Universal Host Controller Interface driver v3.0 kmem_cache_create: duplicate cache uhci_urb_priv kmem_cache_create+0x30f/0x3b0 uhci_hcd_init+0x33/0x92 [uhci_hcd] sys_init_module+0xe2/0x160 syscall_call+0x7/0xb USB Universal Host Controller Interface driver v3.0 kmem_cache_create: duplicate cache uhci_urb_priv kmem_cache_create+0x30f/0x3b0 uhci_hcd_init+0x33/0x92 [uhci_hcd] sys_init_module+0xe2/0x160 syscall_call+0x7/0xb NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' ieee80211_crypt: registered algorithm 'TKIP' ieee80211_crypt: registered algorithm 'CCMP' Linux kernel driver for RTL8180 / RTL8185 based WLAN cards Copyright (c) 2004-2005, Andrea Merello rtl8180: Initializing module rtl8180: Wireless extensions version 20 rtl8180: Initializing proc filesystem rtl8180: Configuring chip resources ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 rtl8180: Memory mapped space @ 0xe2011000 rtl8180: MAC controller is a RTL8185 b/g (V. D) rtl8180: This is a CARDBUS NIC rtl8180: Reported EEPROM chip is a 93c46 (1Kbit) rtl8180: Card MAC address is 00:08:54:ab:85:bd rtl8180: EEPROM version 105 rtl8180: Card reports RF frontend Realtek 8225 rtl8180: WW:This driver has EXPERIMENTAL support for this chipset. rtl8180: WW:use it with care and at your own risk and rtl8180: WW:**PLEASE** REPORT SUCCESS/INSUCCESS TO andreamrl@tiscali.it rtl8180: Energy threshold: b rtl8180: PAPE from CONFIG2: 6 rtl8180: IRQ 10 rtl8180: Driver probe completed rtl8180: Bringing up iface rtl8180: Card successfully reset ADDRCONF(NETDEV_UP): wlan0: link is not ready Linking with RNLAN-AB1 rtl8180: Bringing up iface rtl8180: Card successfully reset Linking with RNLAN-AB1 Linking with RNLAN-AB1 Associated successfully Using B rates ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready wlan0: no IPv6 routers present