******** hosts ******** # # /etc/hosts: static lookup table for host names # # 127.0.0.1 localhost.localdomain localhost # End of file *********************** ******* rc.conf ******* # # /etc/rc.conf - Main Configuration for Arch Linux # # # ----------------------------------------------------------------------- # LOCALIZATION # ----------------------------------------------------------------------- # # LOCALE: available languages can be listed with the 'locale -a' command # HARDWARECLOCK: set to "UTC" or "localtime" # TIMEZONE: timezones are found in /usr/share/zoneinfo # KEYMAP: keymaps are found in /usr/share/kbd/keymaps # CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US) # CONSOLEMAP: found in /usr/share/kbd/consoletrans # USECOLOR: use ANSI color sequences in startup messages # LOCALE="el_GR.utf8" HARDWARECLOCK="UTC" TIMEZONE="Europe/Athens" KEYMAP="us" CONSOLEFONT= CONSOLEMAP= USECOLOR="yes" # # ----------------------------------------------------------------------- # HARDWARE # ----------------------------------------------------------------------- # # Scan hardware and load required modules at bootup MOD_AUTOLOAD="yes" # Module Blacklist - modules in this list will never be loaded by udev MOD_BLACKLIST=() # # Modules to load at boot-up (in this order) # - prefix a module with a ! to blacklist it # MODULES=() # Scan for LVM volume groups at startup, required if you use LVM USELVM="no" # # ----------------------------------------------------------------------- # NETWORKING # ----------------------------------------------------------------------- # HOSTNAME="pumuckl" # # Interfaces to start at boot-up (in this order) # Declare each interface then list in INTERFACES # - prefix an entry in INTERFACES with a ! to disable it # - no hyphens in your interface names - Bash doesn't like it # # Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp") # lo="lo 127.0.0.1" eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255" INTERFACES=(lo eth0) # # Routes to start at boot-up (in this order) # Declare each route then list in ROUTES # - prefix an entry in ROUTES with a ! to disable it # gateway="default gw 192.168.0.1" ROUTES=(!gateway) # # Enable these network profiles at boot-up. These are only useful # if you happen to need multiple network configurations (ie, laptop users) # - set to 'menu' to present a menu during boot-up (dialog package required) # - prefix an entry with a ! to disable it # # Network profiles are found in /etc/network-profiles # #NET_PROFILES=(main) # # ----------------------------------------------------------------------- # DAEMONS # ----------------------------------------------------------------------- # # Daemons to start at boot-up (in this order) # - prefix a daemon with a ! to disable it # - prefix a daemon with a @ to start it up in the background # DAEMONS=(syslog-ng network netfs crond alsa gdm) # End of file *********************** ****** ifconfig ******* [froufrou@pumuckl ~]$ ifconfig eth0 Link encap:Ethernet HWaddr 00:A0:CC:66:3C:05 inet addr:192.168.0.2 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:974 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:10 Base address:0xec00 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1647 errors:0 dropped:0 overruns:0 frame:0 TX packets:1647 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:48057 (46.9 Kb) TX bytes:48057 (46.9 Kb) ppp0 Link encap:Point-to-Point Protocol inet addr:83.212.67.22 P-t-P:83.212.27.228 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:34497 errors:0 dropped:0 overruns:0 frame:0 TX packets:21755 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:45605537 (43.4 Mb) TX bytes:1288254 (1.2 Mb) ***********************