Linux version 2.6.9 (root@Knoppix) (gcc-Version 3.3.5 (Debian 1:3.3.5-1)) #2 SMP Tue Oct 19 23:51:10 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fef0000 (usable) BIOS-e820: 000000001fef0000 - 000000001fef3000 (ACPI NVS) BIOS-e820: 000000001fef3000 - 000000001ff00000 (ACPI data) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 510MB LOWMEM available. found SMP MP-table at 000f5140 On node 0 totalpages: 130800 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126704 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 P4M80P ) @ 0x000f7240 ACPI: RSDT (v001 P4M80P AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fef3040 ACPI: FADT (v001 P4M80P AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fef30c0 ACPI: MADT (v001 P4M80P AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fef86c0 ACPI: DSDT (v001 P4M80P AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: BIOS age (1906) fails cutoff (2001), acpi=force is required to enable ACPI ACPI: Disabling ACPI support Intel MultiProcessor Specification v1.4 Virtual Wire compatibility mode. OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000 Processor #0 15:4 APIC version 17 I/O APIC #2 Version 17 at 0xFEC00000. Enabling APIC mode: Flat. Using 1 I/O APICs Processors: 1 Built 1 zonelists Kernel command line: ramdisk_size=100000 init=/etc/init lang=us apm=power-off desktop=kde vga=normal Initializing CPU#0 PID hash table entries: 2048 (order: 11, 32768 bytes) Detected 3063.654 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 513028k/523200k available (1783k kernel code, 9620k reserved, 930k data, 276k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop... 5996.54 BogoMIPS (lpj=2998272) Security Scaffold v1.0.0 initialized SELinux: Disabled at boot. Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 256K CPU: Hyper-Threading is disabled CPU: After all inits, caps: bfebfbff 20000000 00000000 00000080 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (24) available Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. Checking for popad bug... OK. CPU0: Intel(R) Celeron(R) CPU 3.06GHz stepping 09 per-CPU timeslice cutoff: 731.37 usecs. task migration cache decay timeout: 1 msecs. Total of 1 processors activated (5996.54 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 pin1=2 pin2=0 Brought up 1 CPUs checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 759k freed NET: Registered protocol family 16 EISA bus registered PCI: PCI BIOS revision 2.10 entry at 0xfb3c0, last bus=1 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040816 ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay PnPBIOS: Scanning system for PnP BIOS support... PnPBIOS: Found PnP BIOS installation structure at 0xc00fbe20 PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbe50, dseg 0xf0000 PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver SCSI subsystem initialized PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI->APIC IRQ transform: (B0,I7,P0) -> 16 PCI->APIC IRQ transform: (B0,I9,P0) -> 18 PCI->APIC IRQ transform: (B0,I15,P1) -> 20 PCI->APIC IRQ transform: (B0,I15,P0) -> 20 PCI->APIC IRQ transform: (B0,I16,P0) -> 21 PCI->APIC IRQ transform: (B0,I16,P0) -> 21 PCI->APIC IRQ transform: (B0,I16,P1) -> 21 PCI->APIC IRQ transform: (B0,I16,P1) -> 21 PCI->APIC IRQ transform: (B0,I16,P2) -> 21 PCI->APIC IRQ transform: (B0,I17,P2) -> 22 PCI->APIC IRQ transform: (B0,I18,P0) -> 23 PCI->APIC IRQ transform: (B1,I0,P0) -> 16 audit: initializing netlink socket (disabled) audit(1166813039.580:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API PCI: Via IRQ fixup for 0000:00:10.0, from 10 to 5 PCI: Via IRQ fixup for 0000:00:10.1, from 10 to 5 PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 5 PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 5 vesafb: probe of vesafb0 failed with error -6 isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Using anticipatory io scheduler Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 100000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: SAMSUNG SP0802N, ATA DISK drive hdb: SAMSUNG SP0822N, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: LITE-ON COMBO LTC-48161H, ATAPI CD/DVD-ROM drive hdd: HL-DT-ST DVDRAM GSA-4167B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 Probing IDE interface ide2... ide2: Wait for ready failed before probe ! Probing IDE interface ide3... ide3: Wait for ready failed before probe ! Probing IDE interface ide4... ide4: Wait for ready failed before probe ! Probing IDE interface ide5... ide5: Wait for ready failed before probe ! hda: max request size: 1024KiB hda: Host Protected Area detected. current capacity is 156365903 sectors (80059 MB) native capacity is 156368016 sectors (80060 MB) hda: 156365903 sectors (80059 MB) w/2048KiB Cache, CHS=16383/255/63 hda: cache flushes supported hda: hda1 hda2 < hda5 > hdb: max request size: 1024KiB hdb: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63 hdb: cache flushes supported hdb: hdb1 hdb2 hdb3 hdb4 < hdb5 hdb6 hdb7 > libata version 1.02 loaded. sata_via version 0.20 sata_via(0000:00:0f.0): routed to hard irq line 4 ata1: SATA max UDMA/133 cmd 0xF400 ctl 0xF002 bmdma 0xE400 irq 20 ata2: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xE408 irq 20 ata1: no device found (phy stat 00000000) scsi0 : sata_via ata2: no device found (phy stat 00000000) scsi1 : sata_via mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard on isa0060/serio0 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 EISA: Probing bus 0 at eisa0 EISA: Detected 0 cards. NET: Registered protocol family 2 IP: routing cache hash table of 4096 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 32768) NET: Registered protocol family 1 NET: Registered protocol family 15 RAMDISK: Compressed image found at block 0 EXT2-fs warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device scsi2 : SCSI host adapter emulation for IDE ATAPI devices Vendor: LITE-ON Model: COMBO LTC-48161H Rev: KH0P Type: CD-ROM ANSI SCSI revision: 02 sr0: scsi3-mmc drive: 8x/48x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 Attached scsi CD-ROM sr0 at scsi2, channel 0, id 0, lun 0 scsi3 : SCSI host adapter emulation for IDE ATAPI devices Vendor: HL-DT-ST Model: DVDRAM GSA-4167B Rev: DL12 Type: CD-ROM ANSI SCSI revision: 02 sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray Attached scsi CD-ROM sr1 at scsi3, channel 0, id 0, lun 0 NCR53c406a: no available ports found mptscsih: Unknown symbol mpt_deregister mptscsih: Unknown symbol mpt_reset_deregister mptscsih: Unknown symbol mpt_config mptscsih: Unknown symbol mpt_device_driver_deregister mptscsih: Unknown symbol mpt_free_msg_frame mptscsih: Unknown symbol mpt_print_ioc_summary mptscsih: Unknown symbol mpt_GetIocState mptscsih: Unknown symbol mpt_put_msg_frame mptscsih: Unknown symbol mpt_register mptscsih: Unknown symbol mpt_add_sge mptscsih: Unknown symbol mpt_event_deregister mptscsih: Unknown symbol mpt_read_ioc_pg_3 mptscsih: Unknown symbol mpt_event_register mptscsih: Unknown symbol mpt_send_handshake_request mptscsih: Unknown symbol mpt_device_driver_register mptscsih: Unknown symbol DmpService mptscsih: Unknown symbol mpt_get_msg_frame mptscsih: Unknown symbol mpt_reset_register mptscsih: Unknown symbol mpt_HardResetHandler mptscsih: Unknown symbol ioc_list scsi: Detection failed (no card) GDT-HA: Storage RAID Controller Driver. Version: 3.04 GDT-HA: Found 0 PCI Storage RAID Controllers seagate: ST0x/TMC-8xx not detected. Failed initialization of WD-7000 SCSI card! usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v2.2 uhci_hcd 0000:00:10.0: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller uhci_hcd 0000:00:10.0: irq 21, io base 0000d800 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:10.1: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2) uhci_hcd 0000:00:10.1: irq 21, io base 0000d400 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:10.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3) uhci_hcd 0000:00:10.2: irq 21, io base 0000d000 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:10.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#4) uhci_hcd 0000:00:10.3: irq 21, io base 0000cc00 uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. ub: sizeof ub_scsi_cmd 60 ub_dev 940 usbcore: registered new driver ub ieee1394: Initialized config rom entry `ip1394' ohci1394: $Rev: 1223 $ Ben Collins ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[16] MMIO=[fdfff000-fdfff7ff] Max Packet=[2048] sbp2: Unknown parameter `sbp2_serialize_io' sbp2: $Rev: 1219 $ Ben Collins ieee1394: Host added: ID:BUS[0-00:1023] GUID[0001080037035891] ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A cloop: Initializing cloop v2.01 cloop: loaded (max 8 devices) cloop: /cdrom/KNOPPIX/KNOPPIX: 25883 blocks, 65536 bytes/block, largest block is 65562 bytes. ISO 9660 Extensions: RRIP_1991A Freeing unused kernel memory: 276k freed Generic RTC Driver v1.07 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) Linux Kernel Card Services options: [pci] [cardbus] [pm] Serial: 8250/16550 driver $Revision: 1.90 $ 14 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] Linux agpgart interface v0.100 (c) Dave Jones 8139too Fast Ethernet driver 0.9.27 eth0: RealTek RTL8139 at 0xe08e4000, 00:40:95:30:13:0b, IRQ 18 eth0: Identified 8139 chip type 'RTL-8139C' via-rhine.c:v1.10-LK1.2.0-2.6 June-10-2004 Written by Donald Becker eth1: VIA Rhine II at 0xfdffc000, 00:16:17:7e:a2:cf, IRQ 23. eth1: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1. Via 686a/8233/8235 audio driver 1.9.1-ac4-2.5 via82cxxx: Six channel audio available PCI: Setting latency timer of device 0000:00:11.5 to 64 ac97_codec: AC97 codec, id: ALG96 (Unknown) via82cxxx: Codec rate locked at 48Khz via82cxxx: board #1 at 0xC800, IRQ 22 Adding 409616k swap on /dev/hdb6. Priority:-1 extents:1 eth0: link down NET: Registered protocol family 17 eth1: link up, 100Mbps, full-duplex, lpa 0x45E1 [drm:mga_probe] *ERROR* Cannot initialize the agpgart module. CSLIP: code copyright 1989 Regents of the University of California PPP generic driver version 2.4.2 NET: Registered protocol family 24 eth0: link down eth1: link up, 100Mbps, full-duplex, lpa 0x45E1 NET: Registered protocol family 10 Disabled Privacy Extensions on device c0358dc0(lo) IPv6 over IPv4 tunneling driver ip_tables: (C) 2000-2002 Netfilter core team eth0: no IPv6 routers present eth1: no IPv6 routers present