Section "ServerLayout"

# The Identifier line must be present
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".  In this example, "Mouse1" is the core pointer,
# and "Mouse2" is an extended input device that also generates core
# pointer events (i.e., both mice will move the standard pointer).
	Identifier     "Main Layout"
	Screen      0  "aticonfig-Screen[0]" 0 0
EndSection

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# ModulePath can be used to set a search path for the X server modules.
# The default path is shown here.
#    ModulePath	"/usr/lib64/xorg/modules,/usr/lib64/xorg/modules/drivers,/usr/lib64/xorg/modules/linux,/usr/lib64/xorg/modules/extensions"
	RgbPath      "/usr/share/X11/rgb"
	FontPath     "/usr/share/fonts/local"
	FontPath     "/usr/share/fonts/misc"
	FontPath     "/usr/share/fonts/Type1"
	FontPath     "/usr/share/fonts/TTF"
	FontPath     "/usr/share/fonts/CID"
	FontPath     "/usr/share/fonts/75dpi"
	FontPath     "/usr/share/fonts/100dpi"
EndSection

Section "Module"

# This loads the DBE extension module.
# initialisation of the XFree86-DGA extension within that module.
# This loads the Type1 and FreeType font modules
	Load  "dbe"
# This loads the miscellaneous extensions module, and disables
	SubSection "extmod"
		Option	    "omit xfree86-dga"
	EndSubSection
	Load  "bitmap"
	Load  "xtrap"
	Load  "pcidata"
	Load  "vbe"
	Load  "int10"
	Load  "record"
	
	Load  "type1"
	Load  "freetype"
	Load  "dri"
	Load  "glx"
EndSection

Section "ServerFlags"

# Uncomment this to cause a core dump at the spot where a signal is 
# received.  This may leave the console in an unusable state, but may
# provide a better stack trace in the core dump to aid in debugging
#    Option	"NoTrapSignals"
# Uncomment this to disable the <Crtl><Alt><Fn> VT switch sequence
# (where n is 1 through 12).  This allows clients to receive these key
# events.
#    Option	"DontVTSwitch"
# Uncomment this to disable the <Crtl><Alt><BS> server abort sequence
# This allows clients to receive this key event.
#    Option	"DontZap"
# Uncomment this to disable the <Crtl><Alt><KP_+>/<KP_-> mode switching
# sequences.  This allows clients to receive these key events.
#    Option	"DontZoom"
# Uncomment this to disable tuning with the xvidtune client. With
# it the client can still run and fetch card and monitor attributes,
# but it will not be allowed to change them. If it tries it will
# receive a protocol error.
#    Option	"DisableVidModeExtension"
# Uncomment this to enable the use of a non-local xvidtune client.
#    Option	"AllowNonLocalXvidtune"
# Uncomment this to disable dynamically modifying the input device
# (mouse and keyboard) settings.
#    Option	"DisableModInDev"
# Uncomment this to enable the use of a non-local client to
# change the keyboard or mouse settings (currently only xset).
#    Option	"AllowNonLocalModInDev"
# Set the basic blanking screen saver timeout.
# Set the DPMS timeouts.  These are set here because they are global
# rather than screen-specific.  These settings alone don't enable DPMS.
# It is enabled per-screen (or per-monitor), and even then only when
# the driver supports it.
# memory and pio ranges. This is done by assuming that PCI ranges
# don't overlap. Some broken BIOSes tend to set ranges of inactive
# devices wrong. Here one can adjust how aggressive the assumptions
# should be. Default is 0.
# Option   "EstimateSizesAggresively" "0"
	Option	    "blank time" "10"	# 10 minutes
	Option	    "standby time" "20"
	Option	    "suspend time" "30"
	Option	    "off time" "60"
# On some platform the server needs to estimate the sizes of PCI
EndSection

Section "InputDevice"
	Identifier  "touchpad"
	Driver      "mouse"
	Option	    "Protocol" "Auto"
	Option	    "Emulate3Buttons"
	Option	    "Device" "/dev/input/mice"
EndSection

Section "InputDevice"
	Identifier  "kbd_laptop"
	Driver      "kbd"
	Option	    "XkbModel" "pc105"
	Option	    "XkbLayout" "pl"
EndSection

Section "Monitor"
	Identifier   "aticonfig-Monitor[0]"
	Option	    "VendorName" "ATI Proprietary Driver"
	Option	    "ModelName" "Generic Autodetecting Monitor"
	Option	    "DPMS" "true"
EndSection

Section "Device"
	Identifier  "aticonfig-Device[0]"
	Driver      "fglrx"
	Option	    "mtrr" "no"
	Option	"no_dri" "no"
	Option 	"no_accel" "no"
	Option	    "UseInternalAGPGART" "yes"
	Option	    "MaxGARTSize" "128"
EndSection

Section "Screen"
	Identifier "aticonfig-Screen[0]"
	Device     "aticonfig-Device[0]"
	Monitor    "aticonfig-Monitor[0]"
	DefaultDepth     24
	SubSection "Display"
		Viewport   0 0
		Depth     24
		Modes    "1280x800" "1024x768" "800x600"
	EndSubSection
EndSection

Section "Extensions"
#	Option	    "Composite"
#	Option	    "Damage"
EndSection