mytivo:~# hdparm /dev/hda

/dev/hda:
 multcount    =  0 (off)
 IO_support   =  1 (32-bit)
 unmaskirq    =  1 (on)
 using_dma    =  0 (off)
 keepsettings =  0 (off)
 readonly     =  0 (off)
 readahead    = 256 (on)
 geometry     = 65535/16/63, sectors = 156301488, start = 0


mytivo:~# hdparm -iI /dev/hda

/dev/hda:

 Model=WDC WD800BB-22JHC0, FwRev=05.01C05, SerialNo=WD-WCAM9A942307
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=66
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=off
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=156301488
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: device does not report version:

 * signifies the current active mode


ATA device, with non-removable media
        Model Number:       WDC WD800BB-22JHC0
        Serial Number:      WD-WCAM9A942307
        Firmware Revision:  05.01C05
Standards:
        Supported: 6 5 4 3
        Likely used: 6
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  156301488
        device size with M = 1024*1024:       76319 MBytes
        device size with M = 1000*1000:       80026 MBytes (80 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        bytes avail on r/w long: 66     Queue depth: 1
        Standby timer values: spec'd by Standard, with device specific minimum
        R/W multiple sector transfer: Max = 16  Current = 0
        Recommended acoustic management value: 128, current value: 254
        DMA: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
           *    Look-ahead
           *    Write cache
           *    Power Management feature set
           *    SMART feature set
           *    Mandatory FLUSH CACHE command
           *    Device Configuration Overlay feature set
                Automatic Acoustic Management feature set
                SET MAX security extension
           *    DOWNLOAD MICROCODE cmd
           *    SMART self-test
           *    SMART error logging
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by CSEL
Checksum: correct