metalero9@metalero9:~> dmesg Linux version 2.6.18.2-34-default (geeko@buildhost) (gcc version 4.1.2 20061115 (prerelease) (SUSE Linux)) #1 SMP Mon Nov 27 11:46:27 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002fffc000 (usable) BIOS-e820: 000000002fffc000 - 000000002ffff000 (ACPI data) BIOS-e820: 000000002ffff000 - 0000000030000000 (ACPI NVS) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 767MB LOWMEM available. On node 0 totalpages: 196604 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 192508 pages, LIFO batch:31 DMI 2.3 present. Using APIC driver default IO/L-APIC allowed because system is MP or new enough ACPI: RSDP (v000 ASUS ) @ 0x000f5700 ACPI: RSDT (v001 ASUS P4S800MX 0x42302e31 MSFT 0x31313031) @ 0x2fffc000 ACPI: FADT (v001 ASUS P4S800MX 0x42302e31 MSFT 0x31313031) @ 0x2fffc0c0 ACPI: BOOT (v001 ASUS P4S800MX 0x42302e31 MSFT 0x31313031) @ 0x2fffc030 ACPI: MADT (v001 ASUS P4S800MX 0x42302e31 MSFT 0x31313031) @ 0x2fffc058 ACPI: DSDT (v001 ASUS P4S800MX 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: PM-Timer IO Port: 0xe408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:2 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:2 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 128, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 20 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 40000000 (gap: 30000000:cec00000) Detected 3001.035 MHz processor. Built 1 zonelists. Total pages: 196604 Kernel command line: root=/dev/hda2 vga=0x317 resume=/dev/hda5 splash=silent bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 772264k/786416k available (1697k kernel code, 13452k reserved, 968k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 6005.58 BogoMIPS (lpj=12011173) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code checking if image is initramfs... it is Freeing initrd memory: 3146k freed ACPI: Core revision 20060707 CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 SMP alternatives: switching to SMP code Booting processor 1/1 eip 3000 Initializing CPU#1 Calibrating delay using timer specific routine.. 6002.10 BogoMIPS (lpj=12004207) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: Physical Processor ID: 0 CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel P4/Xeon Extended MCE MSRs (12) available CPU1: Thermal monitoring enabled CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 09 Total of 2 processors activated (12007.69 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization across 2 CPUs: passed. Brought up 2 CPUs migration_cost=170 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xf10c0, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *9 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *9 ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) *9 ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Enabling SiS 96x SMBus. PCI: Ignoring BAR0-3 of IDE controller 0000:00:02.5 Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:02: ioport range 0xe400-0xe47f could not be reserved pnp: 00:02: ioport range 0xe480-0xe4ff has been reserved pnp: 00:02: ioport range 0xe600-0xe61f has been reserved pnp: 00:02: ioport range 0x480-0x48f has been reserved pnp: 00:0e: ioport range 0x295-0x296 has been reserved PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: d7000000-d7ffffff PREFETCH window: dff00000-febfffff PCI: Setting latency timer of device 0000:00:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x3a set to 0x1 Machine check exception polling timer started. apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: disabled - APM is not SMP safe. audit: initializing netlink socket (disabled) audit(1170283952.816:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) vesafb: framebuffer at 0xe0000000, mapped to 0xf0880000, using 6144k, total 262144k vesafb: mode is 1024x768x16, linelength=2048, pages=1 vesafb: protected mode interface info at c000:e2e0 vesafb: pmi: set display start = c00ce316, set palette = c00ce380 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 81749 bytes,<6>...found (1024x768, 46202 bytes, v3). Console: switching to colour frame buffer device 124x44 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice input: PC Speaker as /class/input/input0 input: AT Translated Set 2 keyboard as /class/input/input1 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 1 Using IPI No-Shortcut mode ACPI: (supports S0 S1 S4 S5) Time: tsc clocksource has been installed. Freeing unused kernel memory: 196k freed Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ACPI: Invalid PBLK length [5] SIS5513: IDE controller at PCI slot 0000:00:02.5 ACPI: PCI Interrupt 0000:00:02.5[A] -> GSI 16 (level, low) -> IRQ 177 SIS5513: chipset revision 0 SIS5513: not 100% native mode: will probe irqs later SIS5513: SiS 962/963 MuTIOL IDE UDMA133 controller ide0: BM-DMA at 0xb400-0xb407, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xb408-0xb40f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: ST3120023A, ATA DISK drive hdb: ASUS DVD-E616A2, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: max request size: 128KiB hda: 234375000 sectors (120000 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 < hda5 > hda4 Probing IDE interface ide1... hdc: ASUS CRW-5232A3, ATAPI CD/DVD-ROM drive hdd: BENQ DVD DD DW1640, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3 FS on hda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. Linux video capture interface: v2.00 parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] lp0: using parport0 (interrupt-driven). usbcore: registered new driver usbfs usbcore: registered new driver hub Linux agpgart interface v0.101 (c) Dave Jones bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture bttv: Bt8xx card found (0). ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 18 (level, low) -> IRQ 185 bttv0: Bt878 (rev 17) at 0000:00:0a.0, irq: 185, latency: 32, mmio: 0xdf000000 bttv0: detected: Prolink Pixelview PV-BT [card=72], PCI subsystem ID is 1554:4011 bttv0: using: Prolink Pixelview PV-BT878P+9B (PlayTV Pro rev.9B FM+NICAM) [card=72,autodetected] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) bttv0: gpio: en=00000000, out=00000000 in=006fc0ff [init] i2c-algo-bit.o: (0) scl=1, sda=1 i2c-algo-bit.o: (1) scl=1, sda=0 i2c-algo-bit.o: (2) scl=1, sda=1 i2c-algo-bit.o: (3) scl=0, sda=1 i2c-algo-bit.o: (4) scl=1, sda=1 i2c-algo-bit.o: bt878 #0 [sw] passed test. bttv0: using tuner=5 bttv0: i2c: checking for TDA7432 @ 0x8a... not found bttv0: i2c: checking for TDA9887 @ 0x86... not found sis900.c: v1.08.10 Apr. 2 2006 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 gameport: NS558 PnP Gameport is pnp00:0d/gameport0, io 0x200, speed 840kHz tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw]) tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) tuner 0-0063: chip found @ 0xc6 (bt878 #0 [sw]) ieee1394: Initialized config rom entry `ip1394' bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0 bttv0: PLL: 28636363 => 35468950 .. ok input: bttv IR (card=72) as /class/input/input2 bttv-input: bttv IR (card=72) detected at pci-0000:00:0a.0/ir0 ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 169 ohci_hcd 0000:00:03.0: OHCI Host Controller ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:03.0: irq 169, io mem 0xd6800000 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd usb usb1: SerialNumber: 0000:00:03.0 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected bt878: AUDIO driver version 0.0.0 loaded hdb: ATAPI 48X DVD-ROM drive, 2048kB Cache, UDMA(100) Uniform CD-ROM driver Revision: 3.20 hdc: ATAPI 52X CD-ROM CD-R/RW drive, 1536kB Cache, UDMA(33) hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 193 ohci_hcd 0000:00:03.1: OHCI Host Controller ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:03.1: irq 193, io mem 0xd6000000 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.18.2-34-default ohci_hcd usb usb2: SerialNumber: 0000:00:03.1 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected agpgart: Detected SiS 661 chipset agpgart: AGP aperture is 64M @ 0xd8000000 ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 201 ehci_hcd 0000:00:03.3: EHCI Host Controller ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 3 PCI: cache line size of 128 is not supported by device 0000:00:03.3 ehci_hcd 0000:00:03.3: irq 201, io mem 0xd5800000 ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: new device found, idVendor=0000, idProduct=0000 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: EHCI Host Controller usb usb3: Manufacturer: Linux 2.6.18.2-34-default ehci_hcd usb usb3: SerialNumber: 0000:00:03.3 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 6 ports detected ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 209 ALSA sound/pci/emu10k1/emufx.c:1435: Installing spdif_bug patch: Audigy 2 ZS [SB0350] ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 217 gameport: EMU10K1 is pci0000:00:09.1/gameport0, io 0x9000, speed 1217kHz 0000:00:04.0: VIA 6103 PHY transceiver found at address 1. 0000:00:04.0: Using transceiver found at address 1 as default eth0: SiS 900 PCI Fast Ethernet at 0x9800, IRQ 217, 00:0e:a6:2a:38:7d. sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0xe600 bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:00:0a.1[A] -> GSI 18 (level, low) -> IRQ 185 bt878_probe: card id=[0x40111554], Unknown card. Exiting.. ACPI: PCI interrupt for device 0000:00:0a.1 disabled bt878: probe of 0000:00:0a.1 failed with error -22 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI Interrupt 0000:00:09.2[B] -> GSI 18 (level, low) -> IRQ 185 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[185] MMIO=[d4000000-d40007ff] Max Packet=[2048] IR/IT contexts=[4/8] ohci_hcd 0000:00:03.1: wakeup nvidia: module license 'NVIDIA' taints kernel. usb 2-2: new low speed USB device using ohci_hcd and address 2 usb 2-2: new device found, idVendor=045e, idProduct=00b8 usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-2: Product: Microsoft Optical Mouse by Starck usb 2-2: Manufacturer: Microsoft usb 2-2: configuration #1 chosen from 1 choice ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177 NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006 usbcore: registered new driver hiddev input: Microsoft Microsoft Optical Mouse by Starck as /class/input/input3 input: USB HID v1.10 Mouse [Microsoft Microsoft Optical Mouse by Starck] on usb-0000:00:03.1-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver Adding 2273156k swap on /dev/hda5. Priority:-1 extents:1 across:2273156k ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0151117924] device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com loop: loaded (max 8 devices) kjournald starting. Commit interval 5 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver 2.1.27 [Flags: R/W MODULE]. NTFS volume version 3.1. NTFS-fs warning (device hda1): load_system_files(): Unsupported volume flags 0x4000 encountered. NTFS-fs warning (device hda1): load_system_files(): Volume has unsupported flags set. Will not be able to remount read-write. Run chkdsk and mount in Windows. AppArmor: AppArmor initialized audit(1170283972.837:2): AppArmor initialized ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] powernow: This module only works with AMD K7 CPUs NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver IA-32 Microcode Update Driver: v1.14a microcode: CPU1 updated from revision 0x17 to 0x2e, date = 08112004 microcode: CPU0 updated from revision 0x17 to 0x2e, date = 08112004 audit(1170294784.253:3): audit_pid=3157 old=0 by auid=4294967295 bootsplash: status on console 0 changed to on NET: Registered protocol family 17 eth0: Media Link On 100mbps full-duplex agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode eth0: no IPv6 routers present bttv0: PLL can sleep, using XTAL (28636363). SCSI subsystem initialized st: Version 20050830, fixed bufsize 32768, s/g segs 256 ISO 9660 Extensions: Microsoft Joliet Level 3 ISOFS: changing to secondary root hdb: tray open end_request: I/O error, dev hdb, sector 64 Buffer I/O error on device hdb, logical block 8 hdb: tray open end_request: I/O error, dev hdb, sector 64 Buffer I/O error on device hdb, logical block 8 hdb: tray open end_request: I/O error, dev hdb, sector 64 Buffer I/O error on device hdb, logical block 8 hdb: tray open end_request: I/O error, dev hdb, sector 64 Buffer I/O error on device hdb, logical block 8 metalero9@metalero9:~>