root@morfeas:/home/sisareg# smartctl -a /dev/hda1 smartctl version 5.36 [i486-slackware-linux-gnu] Copyright (C) 2002-6 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Model Family: Maxtor DiamondMax D540X-4D Device Model: Maxtor 4D040H2 Serial Number: D249CVHE Firmware Version: DAH017K0 User Capacity: 40,982,151,168 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 6 ATA Standard is: ATA/ATAPI-6 T13 1410D revision 0 Local Time is: Mon Feb 26 22:50:18 2007 EET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: FAILED! Drive failure expected in less than 24 hours. SAVE ALL DATA. See vendor-specific Attribute list for failed Attributes. General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 30) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 27) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 3 Spin_Up_Time 0x0027 234 233 063 Pre-fail Always - 5419 4 Start_Stop_Count 0x0032 253 253 000 Old_age Always - 1921 5 Reallocated_Sector_Ct 0x0033 007 007 063 Pre-fail Always FAILING_NOW 619 6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline - 0 7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always - 0 8 Seek_Time_Performance 0x0027 253 232 187 Pre-fail Always - 32979 9 Power_On_Minutes 0x0032 247 247 000 Old_age Always - 170h+24m 10 Spin_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0 11 Calibration_Retry_Count 0x002b 253 252 223 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 248 248 000 Old_age Always - 2019 192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always - 0 193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always - 0 194 Unknown_Attribute 0x0032 253 253 000 Old_age Always - 0 195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always - 738 196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline - 0 197 Current_Pending_Sector 0x0008 001 001 000 Old_age Offline - 297 198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0008 052 001 000 Old_age Offline - 667 200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always - 0 201 Soft_Read_Error_Rate 0x000a 253 248 000 Old_age Always - 32 202 TA_Increase_Count 0x000a 253 242 000 Old_age Always - 0 203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always - 7 204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always - 0 205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always - 0 207 Spin_High_Current 0x002a 253 252 000 Old_age Always - 0 208 Spin_Buzz 0x002a 253 252 000 Old_age Always - 0 209 Offline_Seek_Performnce 0x0024 253 253 000 Old_age Offline - 0 99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 40940 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 40940 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 0b 4f c2 e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 00 4f c2 e0 08 04:01:20.880 SMART RETURN STATUS ec 00 00 9e 8e 03 e0 08 04:01:20.880 IDENTIFY DEVICE ca 00 08 97 8e 03 e0 08 04:01:18.496 WRITE DMA ca 00 08 67 17 02 e0 08 04:01:18.496 WRITE DMA ca 00 08 07 bc 01 e0 08 04:01:18.496 WRITE DMA Error 40939 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 0b 4f c2 e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 00 4f c2 e0 08 04:01:05.936 SMART RETURN STATUS ec 00 00 c6 00 00 e0 08 04:01:05.920 IDENTIFY DEVICE ca 00 08 bf 00 00 e0 08 04:00:55.616 WRITE DMA ca 00 08 57 ad 2b e0 08 04:00:55.616 WRITE DMA ca 00 08 57 56 00 e0 08 04:00:55.616 WRITE DMA Error 40938 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 0b 4f c2 e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 00 4f c2 e0 08 04:00:50.224 SMART RETURN STATUS ec 00 00 9e 8e 03 e0 08 04:00:50.208 IDENTIFY DEVICE ca 00 08 97 8e 03 e0 08 04:00:47.984 WRITE DMA ca 00 08 67 17 02 e0 08 04:00:47.984 WRITE DMA ca 00 08 07 bc 01 e0 08 04:00:47.984 WRITE DMA Error 40937 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 00 0b 4f c2 e0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- b0 da 00 00 4f c2 e0 08 03:58:44.288 SMART RETURN STATUS c8 00 40 e7 15 04 e0 08 03:58:44.272 READ DMA ec 00 00 a6 15 04 e0 08 03:58:44.272 IDENTIFY DEVICE c8 00 40 67 15 04 e0 08 03:58:44.272 READ DMA c8 00 40 a7 15 04 e0 08 03:58:44.272 READ DMA Error 40936 occurred at disk power-on lifetime: 2207 hours (91 days + 23 hours) When the command that caused the error occurred, the device was in an unknown state. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 51 05 01 00 00 a0 Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- a1 00 05 01 00 00 a0 08 03:46:43.792 IDENTIFY PACKET DEVICE c8 00 08 9f bc 01 e0 08 03:46:30.800 READ DMA ca 00 08 cf 00 01 e0 08 03:46:30.016 WRITE DMA ca 00 08 bf 00 00 e0 08 03:46:30.016 WRITE DMA ca 00 08 b7 dd 00 e0 08 03:46:30.016 WRITE DMA SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging