U-Boot 1.1.2 (Aug 28 2005 - 13:37:25) QNAP System, Inc. CPU: MPC8245 Revision 1.4 at 266.666 MHz: 16 kB I-Cache 16 kB D-Cache Board: Sandpoint 8245 Unity ##Test not implemented yet## I2C: ready DRAM: 64 MB FLASH: S29GL128N, 16 MB In: serial Out: serial Err: serial Net: No ethernet found. Hit any key to stop autoboot: 0 ## Starting application at 0xFFE60100 ... U-Boot 1.2.0 (Feb 26 2007 - 16:15:28) OpenTS(c) CPU: MPC8241 Revision 1.4 at 266.666 MHz: 16 kB I-Cache 16 kB D-Cache Board: QNAP TS-101/TS-201 local bus at 133.333 MHz I2C: ready DRAM: 64 MB FLASH: 16 MB In: serial Out: serial Err: serial Net: RTL8169sc/8110sc... RTL8169#0 IDE: Bus 0: OK Bus 1: not available Device 0: Model: SAMSUNG SP2504C Firm: VT100-41 Ser#: S09QJ1GL709404 Type: Hard Disk Supports 48-bit addressing Capacity: 238475.1 MB = 232.8 GB (488397168 x 512) Device 1: not available Hit any key to stop autoboot: 0 => run testkernel 1829720 bytes read ## Booting image at 00300000 ... Image Name: Linux-2.6.21-rc1-opents Created: 2007-02-27 18:37:09 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1829656 Bytes = 1.7 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.6.21-rc1-opents (repvik@apollo) (gcc version 3.4.6) #2 Tue Feb 27 19:37:07 CET 2007 Motorola SPS Sandpoint Test Platform Port by MontaVista Software, Inc. (source@mvista.com) Zone PFN ranges: DMA 0 -> 16384 Normal 16384 -> 16384 early_node_map[1] active PFN ranges 0: 0 -> 16384 Built 1 zonelists. Total pages: 16256 Kernel command line: console=ttyS0,115200n8 root=/dev/ram rtc-rs5c372.probe=0,0x32 OpenPIC Version 1.2 (1 CPUs and 10 IRQ sources) at fdf40000 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61056k available (2856k kernel code, 892k data, 124k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Cannot allocate resource region 1 of device 0000:00:00.0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 25) is a 16550A serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMfdf04500 IRQ25): -28 RAMDISK driver initialized: 16 RAM disks of 40960K size 1024 blocksize loop: loaded (max 8 devices) Intel(R) PRO/1000 Network Driver - version 7.3.20-k2 Copyright (c) 1999-2006 Intel Corporation. eth0: r10001.05, the Linux device driver for Realtek Ethernet Controllers at 0xbffe00, 00:e0:4c:69:20:01, IRQ 18 Realtek RTL8169/8110 Family Gigabit Ethernet Network Adapter Driver version:1.05 Released date:2006/10/25 Link Status:Linked Link Speed:100Mbps Duplex mode:Full-Duplex I/O Base:0xBFFE00(I/O port) IRQ:18 sata_sil 0000:00:0d.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xc5050e80 ctl 0xc5050e8a bmdma 0xc5050e00 irq 16 ata2: SATA max UDMA/100 cmd 0xc5050ec0 ctl 0xc5050eca bmdma 0xc5050e08 irq 16 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-7: SAMSUNG SP2504C, VT100-41, max UDMA7 ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP2504C VT10 PQ: 0 ANSI: 5 SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB) sda: Write Protect is off SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 physmap platform flash device: 01000000 at ff000000 physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 physmap-flash.0: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. RedBoot partition parsing not available Using physmap partition information Creating 7 MTD partitions on "physmap-flash.0": 0x00f00000-0x00f40000 : "U-Boot" 0x00000000-0x00200000 : "Kernel" 0x00200000-0x00b00000 : "RootFS1" 0x00b00000-0x00e00000 : "RootFS2" 0x00e00000-0x00f00000 : "Vendor" 0x00f40000-0x00f60000 : "U-Boot Config" 0x00f60000-0x01000000 : "NAS Config" ehci_hcd 0000:00:0e.2: EHCI Host Controller ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0e.2: request interrupt 17 failed ehci_hcd 0000:00:0e.2: USB bus 1 deregistered ehci_hcd 0000:00:0e.2: init 0000:00:0e.2 fail, -16 ehci_hcd: probe of 0000:00:0e.2 failed with error -16 ohci_hcd 0000:00:0e.0: OHCI Host Controller ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.0: request interrupt 17 failed ohci_hcd 0000:00:0e.0: USB bus 1 deregistered ohci_hcd 0000:00:0e.0: init 0000:00:0e.0 fail, -16 ohci_hcd: probe of 0000:00:0e.0 failed with error -16 ohci_hcd 0000:00:0e.1: OHCI Host Controller ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.1: request interrupt 17 failed ohci_hcd 0000:00:0e.1: USB bus 1 deregistered ohci_hcd 0000:00:0e.1: init 0000:00:0e.1 fail, -16 ohci_hcd: probe of 0000:00:0e.1 failed with error -16 usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. rtc-rs5c372 0-0032: assuming rs5c372b rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.4 rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 rtc-rs5c372 0-0032: setting the system clock to 2007-02-27 07:43:31 (1172562211)