zapata.conf =================== ; ; Zapata telephony interface ; ; Configuration file [trunkgroups] [channels] language=en context=from-pstn signalling=fxs_ks rxwink=300 ; Atlas seems to use long (250ms) winks ; ; Whether or not to do distinctive ring detection on FXO lines ; ;usedistinctiveringdetection=yes usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=no echotraining=800 rxgain=0.0 txgain=0.0 group=0 callgroup=1 pickupgroup=1 immediate=no ;faxdetect=both faxdetect=incoming ;faxdetect=outgoing ;faxdetect=no ;Include genzaptelconf configs #include zapata-auto.conf ;Include AMP configs #include zapata_additional.conf ; ; Zapata telephony interface ; ; Configuration file ; ; You need to restart Asterisk to re-configure the Zap channel ; CLI> reload chan_zap.so ; will reload the configuration file, ; but not all configuration options are ; re-configured during a reload. [trunkgroups] ; ; Trunk groups are used for NFAS or GR-303 connections. ; ; Group: Defines a trunk group. ; group => ,[,...] ; ; trunkgroup is the numerical trunk group to create ; dchannel is the zap channel which will have the ; d-channel for the trunk. ; backup1 is an optional list of backup d-channels. ; ;trunkgroup => 1,24,48 ;trunkgroup => 1,24 ; ; Spanmap: Associates a span with a trunk group ; spanmap => ,[,] ; ; zapspan is the zap span number to associate ; trunkgroup is the trunkgroup (specified above) for the mapping ; logicalspan is the logical span number within the trunk group to use. ; if unspecified, no logical span number is used. ; ;spanmap => 1,1,1 ;spanmap => 2,1,2 ;spanmap => 3,1,3 ;spanmap => 4,1,4 [channels] ; ; Default language ; ;language=en ; ; Default context ; context=default ; ; Switchtype: Only used for PRI. ; ; national: National ISDN 2 (default) ; dms100: Nortel DMS100 ; 4ess: AT&T 4ESS ; 5ess: Lucent 5ESS ; euroisdn: EuroISDN ; ni1: Old National ISDN 1 ; qsig: Q.SIG ; switchtype=national ; ; Some switches (AT&T especially) require network specific facility IE ; supported values are currently 'none', 'sdn', 'megacom', 'accunet' ; ;nsf=none ; ; PRI Dialplan: Only RARELY used for PRI. ; ; unknown: Unknown ; private: Private ISDN ; local: Local ISDN ; national: National ISDN ; international: International ISDN ; ;pridialplan=national ; ; PRI Local Dialplan: Only RARELY used for PRI (sets the calling number's numbering plan) ; ; unknown: Unknown ; private: Private ISDN ; local: Local ISDN ; national: National ISDN ; international: International ISDN ; ;prilocaldialplan=national ; ; PRI callerid prefixes based on the given TON/NPI (dialplan) ; This is especially needed for euroisdn E1-PRIs ; ; sample 1 for Germany ;internationalprefix = 00 ;nationalprefix = 0 ;localprefix = 0711 ;privateprefix = 07115678 ;unknownprefix = ; ; sample 2 for Germany ;internationalprefix = + ;nationalprefix = +49 ;localprefix = +49711 ;privateprefix = +497115678 ;unknownprefix = ; ; PRI resetinterval: sets the time in seconds between restart of unused ; channels, defaults to 3600; minimum 60 seconds. Some PBXs don't like ; channel restarts. so set the interval to a very long interval e.g. 100000000 ; or 'never' to disable *entirely*. ; ;resetinterval = 3600 ; ; Overlap dialing mode (sending overlap digits) ; ;overlapdial=yes ; ; PRI Out of band indications. ; Enable this to report Busy and Congestion on a PRI using out-of-band ; notification. Inband indication, as used by Asterisk doesn't seem to work ; with all telcos. ; ; outofband: Signal Busy/Congestion out of band with RELEASE/DISCONNECT ; inband: Signal Busy/Congestion using in-band tones ; ; priindication = outofband ; ; If you need to override the existing channels selection routine and force all ; PRI channels to be marked as exclusively selected, set this to yes. ; priexclusive = yes ; ; ISDN Timers ; All of the ISDN timers and counters that are used are configurable. Specify ; the timer name, and its value (in ms for timers). ; ; pritimer => t200,1000 ; pritimer => t313,4000 ; ; To enable transmission of facility-based ISDN supplementary services (such ; as caller name from CPE over facility), enable this option. ; facilityenable = yes ; ; ; Signalling method (default is fxs). Valid values: ; em: E & M ; em_w: E & M Wink ; featd: Feature Group D (The fake, Adtran style, DTMF) ; featdmf: Feature Group D (The real thing, MF (domestic, US)) ; featdmf_ta: Feature Group D (The real thing, MF (domestic, US)) through ; a Tandem Access point ; featb: Feature Group B (MF (domestic, US)) ; fxs_ls: FXS (Loop Start) ; fxs_gs: FXS (Ground Start) ; fxs_ks: FXS (Kewl Start) ; fxo_ls: FXO (Loop Start) ; fxo_gs: FXO (Ground Start) ; fxo_ks: FXO (Kewl Start) ; pri_cpe: PRI signalling, CPE side ; pri_net: PRI signalling, Network side ; gr303fxoks_net: GR-303 Signalling, FXO Loopstart, Network side ; gr303fxsks_cpe: GR-303 Signalling, FXS Loopstart, CPE side ; sf: SF (Inband Tone) Signalling ; sf_w: SF Wink ; sf_featd: SF Feature Group D (The fake, Adtran style, DTMF) ; sf_featdmf: SF Feature Group D (The real thing, MF (domestic, US)) ; sf_featb: SF Feature Group B (MF (domestic, US)) ; e911: E911 (MF) style signalling ; ; The following are used for Radio interfaces: ; fxs_rx: Receive audio/COR on an FXS kewlstart interface (FXO at the ; channel bank) ; fxs_tx: Transmit audio/PTT on an FXS loopstart interface (FXO at the ; channel bank) ; fxo_rx: Receive audio/COR on an FXO loopstart interface (FXS at the ; channel bank) ; fxo_tx: Transmit audio/PTT on an FXO groundstart interface (FXS at ; the channel bank) ; em_rx: Receive audio/COR on an E&M interface (1-way) ; em_tx: Transmit audio/PTT on an E&M interface (1-way) ; em_txrx: Receive audio/COR AND Transmit audio/PTT on an E&M interface ; (2-way) ; em_rxtx: Same as em_txrx (for our dyslexic friends) ; sf_rx: Receive audio/COR on an SF interface (1-way) ; sf_tx: Transmit audio/PTT on an SF interface (1-way) ; sf_txrx: Receive audio/COR AND Transmit audio/PTT on an SF interface ; (2-way) ; sf_rxtx: Same as sf_txrx (for our dyslexic friends) ; signalling=fxo_ls ; ; For Feature Group D Tandem access, to set the default CIC and OZZ use these ; parameters: ;defaultozz=0000 ;defaultcic=303 ; ; A variety of timing parameters can be specified as well ; Including: ; prewink: Pre-wink time (default 50ms) ; preflash: Pre-flash time (default 50ms) ; wink: Wink time (default 150ms) ; flash: Flash time (default 750ms) ; start: Start time (default 1500ms) ; rxwink: Receiver wink time (default 300ms) ; rxflash: Receiver flashtime (default 1250ms) ; debounce: Debounce timing (default 600ms) ; rxwink=300 ; Atlas seems to use long (250ms) winks ; ; How long generated tones (DTMF and MF) will be played on the channel ; (in miliseconds) ;toneduration=100 ; ; Whether or not to do distinctive ring detection on FXO lines ; ;usedistinctiveringdetection=yes ; ; Whether or not to use caller ID ; usecallerid=yes ; ; Type of caller ID signalling in use ; bell = bell202 as used in US ; v23 = v23 as used in the UK ; dtmf = DTMF as used in Denmark, Sweden and Netherlands ; ;cidsignalling=bell ; ; What signals the start of caller ID ; ring = a ring signals the start ; polarity = polarity reversal signals the start ; ;cidstart=ring ; ; Whether or not to hide outgoing caller ID (Override with *67 or *82) ; hidecallerid=no ; ; Whether or not to enable call waiting on FXO lines ; callwaiting=yes ; ; Whether or not restrict outgoing caller ID (will be sent as ANI only, not ; available for the user) ; Mostly use with FXS ports ; ;restrictcid=no ; ; Whether or not use the caller ID presentation for the outgoing call that the ; calling switch is sending. ; usecallingpres=yes ; ; Some countries (UK) have ring tones with different ring tones (ring-ring), ; which means the callerid needs to be set later on, and not just after ; the first ring, as per the default. ; ;sendcalleridafter=1 ; ; ; Support Caller*ID on Call Waiting ; callwaitingcallerid=yes ; ; Support three-way calling ; threewaycalling=yes ; ; Support flash-hook call transfer (requires three way calling) ; Also enables call parking (overrides the 'canpark' parameter) ; transfer=yes ; ; Allow call parking ; ('canpark=no' is overridden by 'transfer=yes') ; canpark=yes ; ; Support call forward variable ; cancallforward=yes ; ; Whether or not to support Call Return (*69) ; callreturn=yes ; ; Stutter dialtone support: If a mailbox is specified without a voicemail ; context, then when voicemail is received in a mailbox in the default ; voicemail context in voicemail.conf, taking the phone off hook will cause a ; stutter dialtone instead of a normal one. ; ; If a mailbox is specified *with* a voicemail context, the same will result ; if voicemail recieved in mailbox in the specified voicemail context. ; ; for default voicemail context, the example below is fine: ; ;mailbox=1234 ; ; for any other voicemail context, the following will produce the stutter tone: ; ;mailbox=1234@context ; ; Enable echo cancellation ; Use either "yes", "no", or a power of two from 32 to 256 if you wish to ; actually set the number of taps of cancellation. ; echocancel=yes ; ; Generally, it is not necessary (and in fact undesirable) to echo cancel when ; the circuit path is entirely TDM. You may, however, reverse this behavior ; by enabling the echo cancel during pure TDM bridging below. ; echocancelwhenbridged=yes ; ; In some cases, the echo canceller doesn't train quickly enough and there ; is echo at the beginning of the call. Enabling echo training will cause ; asterisk to briefly mute the channel, send an impulse, and use the impulse ; response to pre-train the echo canceller so it can start out with a much ; closer idea of the actual echo. Value may be "yes", "no", or a number of ; milliseconds to delay before training (default = 400) ; ;echotraining=yes ;echotraining=800 ; ; If you are having trouble with DTMF detection, you can relax the DTMF ; detection parameters. Relaxing them may make the DTMF detector more likely ; to have "talkoff" where DTMF is detected when it shouldn't be. ; ;relaxdtmf=yes ; ; You may also set the default receive and transmit gains (in dB) ; rxgain=0.0 txgain=0.0 ; ; Logical groups can be assigned to allow outgoing rollover. Groups range ; from 0 to 63, and multiple groups can be specified. ; group=1 ; ; Ring groups (a.k.a. call groups) and pickup groups. If a phone is ringing ; and it is a member of a group which is one of your pickup groups, then ; you can answer it by picking up and dialing *8#. For simple offices, just ; make these both the same ; callgroup=1 pickupgroup=1 ; ; Specify whether the channel should be answered immediately or if the simple ; switch should provide dialtone, read digits, etc. ; immediate=no ; ; Specify whether flash-hook transfers to 'busy' channels should complete or ; return to the caller performing the transfer (default is yes). ; ;transfertobusy=no ; ; CallerID can be set to "asreceived" or a specific number if you want to ; override it. Note that "asreceived" only applies to trunk interfaces. ; ;callerid=2564286000 ; ; AMA flags affects the recording of Call Detail Records. If specified ; it may be 'default', 'omit', 'billing', or 'documentation'. ; ;amaflags=default ; ; Channels may be associated with an account code to ease ; billing ; ;accountcode=lss0101 ; ; ADSI (Analog Display Services Interface) can be enabled on a per-channel ; basis if you have (or may have) ADSI compatible CPE equipment ; ;adsi=yes ; ; On trunk interfaces (FXS) and E&M interfaces (E&M, Wink, Feature Group D ; etc, it can be useful to perform busy detection either in an effort to ; detect hangup or for detecting busies. This enables listening for ; the beep-beep busy pattern. ; ;busydetect=yes ; ; If busydetect is enabled, it is also possible to specify how many busy tones ; to wait for before hanging up. The default is 4, but better results can be ; achieved if set to 6 or even 8. Mind that the higher the number, the more ; time that will be needed to hangup a channel, but lowers the probability ; that you will get random hangups. ; ;busycount=4 ; ; If busydetect is enabled, it is also possible to specify the cadence of your ; busy signal. In many countries, it is 500msec on, 500msec off. Without ; busypattern specified, we'll accept any regular sound-silence pattern that ; repeats times as a busy signal. If you specify busypattern, ; then we'll further check the length of the sound (tone) and silence, which ; will further reduce the chance of a false positive. ; ;busypattern=500,500 ; ; NOTE: In the Asterisk Makefile you'll find further options to tweak the busy ; detector. If your country has a busy tone with the same length tone and ; silence (as many countries do), consider defining the ; -DBUSYDETECT_COMPARE_TONE_AND_SILENCE option. ; ; Use a polarity reversal to mark when a outgoing call is answered by the ; remote party. ; ;answeronpolarityswitch=yes ; ; In some countries, a polarity reversal is used to signal the disconnect of a ; phone line. If the hanguponpolarityswitch option is selected, the call will ; be considered "hung up" on a polarity reversal. ; ;hanguponpolarityswitch=yes ; ; On trunk interfaces (FXS) it can be useful to attempt to follow the progress ; of a call through RINGING, BUSY, and ANSWERING. If turned on, call ; progress attempts to determine answer, busy, and ringing on phone lines. ; This feature is HIGHLY EXPERIMENTAL and can easily detect false answers, ; so don't count on it being very accurate. ; ; Few zones are supported at the time of this writing, but may be selected ; with "progzone" ; ; This feature can also easily detect false hangups. The symptoms of this is ; being disconnected in the middle of a call for no reason. ; ;callprogress=yes ;progzone=us ; ; FXO (FXS signalled) devices must have a timeout to determine whe there was a ; hangup before the line was answered. This value can be tweaked to shorten ; how long it takes before Zap considers a non-ringing line to have hungup. ; ;ringtimeout=8000 ; ; For FXO (FXS signalled) devices, whether to use pulse dial instead of DTMF ; ;pulsedial=yes ; ; For fax detection, uncomment one of the following lines. The default is *OFF* ; ;faxdetect=both ;faxdetect=incoming ;faxdetect=outgoing ;faxdetect=no ; ; Select which class of music to use for music on hold. If not specified ; then the default will be used. ; ;musiconhold=default ; ; PRI channels can have an idle extension and a minunused number. So long as ; at least "minunused" channels are idle, chan_zap will try to call "idledial" ; on them, and then dump them into the PBX in the "idleext" extension (which ; is of the form exten@context). When channels are needed the "idle" calls ; are disconnected (so long as there are at least "minidle" calls still ; running, of course) to make more channels available. The primary use of ; this is to create a dynamic service, where idle channels are bundled through ; multilink PPP, thus more efficiently utilizing combined voice/data services ; than conventional fixed mappings/muxings. ; ;idledial=6999 ;idleext=6999@dialout ;minunused=2 ;minidle=1 ; ; Configure jitter buffers in zapata (each one is 20ms, default is 4) ; ;jitterbuffers=4 ; ; You can define your own custom ring cadences here. You can define up to 8 ; pairs. If the silence is negative, it indicates where the callerid spill is ; to be placed. Also, if you define any custom cadences, the default cadences ; will be turned off. ; ; Syntax is: cadence=ring,silence[,ring,silence[...]] ; ; These are the default cadences: ; ;cadence=125,125,2000,-4000 ;cadence=250,250,500,1000,250,250,500,-4000 ;cadence=125,125,125,125,125,-4000 ;cadence=1000,500,2500,-5000 ; ; Each channel consists of the channel number or range. It inherits the ; parameters that were specified above its declaration. ; ; For GR-303, CRV's are created like channels except they must start with the ; trunk group followed by a colon, e.g.: ; ; crv => 1:1 ; crv => 2:1-2,5-8 ; ; ;callerid="Green Phone"<(256) 428-6121> ;channel => 1 ;callerid="Black Phone"<(256) 428-6122> ;channel => 2 ;callerid="CallerID Phone" <(256) 428-6123> ;callerid="CallerID Phone" <(630) 372-1564> ;callerid="CallerID Phone" <(256) 704-4666> ;channel => 3 ;callerid="Pac Tel Phone" <(256) 428-6124> ;channel => 4 ;callerid="Uniden Dead" <(256) 428-6125> ;channel => 5 ;callerid="Cortelco 2500" <(256) 428-6126> ;channel => 6 ;callerid="Main TA 750" <(256) 428-6127> ;channel => 44 ; ; For example, maybe we have some other channels which start out in a ; different context and use E & M signalling instead. ; ;context=remote ;sigalling=em ;channel => 15 ;channel => 16 ;signalling=em_w ; ; All those in group 0 I'll use for outgoing calls ; ; Strip most significant digit (9) before sending ; ;stripmsd=1 ;callerid=asreceived ;group=0 ;signalling=fxs_ls ;channel => 45 ;signalling=fxo_ls ;group=1 ;callerid="Joe Schmoe" <(256) 428-6131> ;channel => 25 ;callerid="Megan May" <(256) 428-6132> ;channel => 26 ;callerid="Suzy Queue" <(256) 428-6233> ;channel => 27 ;callerid="Larry Moe" <(256) 428-6234> ;channel => 28 ; ; Sample PRI (CPE) config: Specify the switchtype, the signalling as either ; pri_cpe or pri_net for CPE or Network termination, and generally you will ; want to create a single "group" for all channels of the PRI. ; ; switchtype = national ; signalling = pri_cpe ; group = 2 ; channel => 1-23 ; ; Used for distintive ring support for x100p. ; You can see the dringX patterns is to set any one of the dringXcontext fields ; and they will be printed on the console when an inbound call comes in. ; ;dring1=95,0,0 ;dring1context=internal1 ;dring2=325,95,0 ;dring2context=internal2 ; If no pattern is matched here is where we go. ;context=default ;channel => 1 ================================================================================================= ============================= /etc/zaptel.conf================================================== ================================================================================================= # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCFXO/0 "Wildcard X101P Board 1" RED fxsks=1 # Span 2: WCFXO/1 "Wildcard X101P Board 2" RED fxsks=2 # Global data loadzone = us defaultzone = us # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=,,,,[,yellow] # # All T1/E1 spans generate a clock signal on their transmit side. The # parameter determines whether the clock signal from the far # end of the T1/E1 is used as the master source of clock timing. If it is, our # own clock will synchronise to it. T1/E1's connected directly or indirectly to # a PSTN provider (telco) should generally be the first choice to sync to. The # PSTN will never be a slave to you. You must be a slave to it. # # Choose 1 to make the equipment at the far end of the E1/T1 link the preferred # source of the master clock. Choose 2 to make it the second choice for the master # clock, if the first choice port fails (the far end dies, a cable breaks, or # whatever). Choose 3 to make a port the third choice, and so on. If you have, say, # 2 ports connected to the PSTN, mark those as 1 and 2. The number used for each # port should be different. # # If you choose 0, the port will never be used as a source of timing. This is # appropriate when you know the far end should always be a slave to you. If the # port is connected to a channel bank, for example, you should always be its # master. Any number of ports can be marked as 0. # # Incorrect timing sync may cause clicks/noise in the audio, poor quality or failed # faxes, unreliable modem operation, and is a general all round bad thing. # # The line build-out (or LBO) is an integer, from the following table: # 0: 0 db (CSU) / 0-133 feet (DSX-1) # 1: 133-266 feet (DSX-1) # 2: 266-399 feet (DSX-1) # 3: 399-533 feet (DSX-1) # 4: 533-655 feet (DSX-1) # 5: -7.5db (CSU) # 6: -15db (CSU) # 7: -22.5db (CSU) # # The framing is one of "d4" or "esf" for T1 or "cas" or "ccs" for E1 # # Note: "d4" could be referred to as "sf" or "superframe" # # The coding is one of "ami" or "b8zs" for T1 or "ami" or "hdb3" for E1 # # E1's may have the additional keyword "crc4" to enable CRC4 checking # # If the keyword "yellow" follows, yellow alarm is transmitted when no # channels are open. # #span=1,0,0,esf,b8zs #span=2,1,0,esf,b8zs #span=3,0,0,ccs,hdb3,crc4 # # Next come the dynamic span definitions, in the form: # dynamic=,
,, # # Where is the name of the driver (e.g. eth),
is the # driver specific address (like a MAC for eth), is the number # of channels, and is a timing priority, like for a normal span. # use "0" to not use this as a timing source, or prioritize them as # primary, secondard, etc. Note that you MUST have a REAL zaptel device # if you are not using external timing. # # dynamic=eth,eth0/00:02:b3:35:43:9c,24,0 # # Next come the definitions for using the channels. The format is: # = # # Valid devices are: # # "e&m" : Channel(s) are signalled using E&M signalling (specific # implementation, such as Immediate, Wink, or Feature Group D # are handled by the userspace library). # "fxsls" : Channel(s) are signalled using FXS Loopstart protocol. # "fxsgs" : Channel(s) are signalled using FXS Groundstart protocol. # "fxsks" : Channel(s) are signalled using FXS Koolstart protocol. # "fxols" : Channel(s) are signalled using FXO Loopstart protocol. # "fxogs" : Channel(s) are signalled using FXO Groundstart protocol. # "fxoks" : Channel(s) are signalled using FXO Koolstart protocol. # "sf" : Channel(s) are signalled using in-band single freq tone. # Syntax as follows: # channel# => sf:,,,,, # rxfreq is rx tone freq in hz, rxbw is rx notch (and decode) # bandwith in hz (typically 10.0), rxflag is either 'normal' or # 'inverted', txfreq is tx tone freq in hz, txlevel is tx tone # level in dbm, txflag is either 'normal' or 'inverted'. Set # rxfreq or txfreq to 0.0 if that tone is not desired. # "unused" : No signalling is performed, each channel in the list remains idle # "clear" : Channel(s) are bundled into a single span. No conversion or # signalling is performed, and raw data is available on the master. # "indclear": Like "clear" except all channels are treated individually and # are not bundled. "bchan" is an alias for this. # "rawhdlc" : The zaptel driver performs HDLC encoding and decoding on the # bundle, and the resulting data is communicated via the master # device. # "fcshdlc" : The zapdel driver performs HDLC encoding and decoding on the # bundle and also performs incoming and outgoing FCS insertion # and verification. "dchan" is an alias for this. # "nethdlc" : The zaptel driver bundles the channels together into an # hdlc network device, which in turn can be configured with # sethdlc (available separately). # "dacs" : The zaptel driver cross connects the channels starting at # the channel number listed at the end, after a colon # "dacsrbs" : The zaptel driver cross connects the channels starting at # the channel number listed at the end, after a colon and # also performs the DACSing of RBS bits # # The channel list is a comma-separated list of channels or ranges, for # example: # # 1,3,5 (channels one, three, and five) # 16-23, 29 (channels 16 through 23, as well as channel 29 # # So, some complete examples are: # e&m=1-12 # nethdlc=13-24 # fxsls=25,26,27,28 # fxols=29-32 # #fxoks=1-24 #bchan=25-47 #dchan=48 #fxols=1-12 #fxols=13-24 #e&m=25-29 #nethdlc=30-33 #clear=44 #clear=45 #clear=46 #clear=47 #fcshdlc=48 #dacs=1-24:48 #dacsrbs=1-24:48 # # Finally, you can preload some tone zones, to prevent them from getting # overwritten by other users (if you allow non-root users to open /dev/zap/* # interfaces anyway. Also this means they won't have to be loaded at runtime. # The format is "loadzone=" where the zone is a two letter country code. # # You may also specify a default zone with "defaultzone=" where zone # is a two letter country code. # # An up-to-date list of the zones can be found in the file zaptel/zonedata.c # loadzone = us #loadzone = us-old #loadzone=gr #loadzone=it #loadzone=fr #loadzone=de #loadzone=uk #loadzone=fi #loadzone=jp #loadzone=sp #loadzone=no #loadzone=hu #loadzone=lt #loadzone=pl defaultzone=us # # Section for PCI Radio Interface # (see http://www.zapatatelephony.org/app_rpt.html) # # The PCI Radio Interface card interfaces up to 4 two-way radios (either # a base/mobile radio or repeater system) to Zaptel channels. The driver # may work either independent of an application, or with it, through # the driver;s ioctl() interface. This file gives you access to specify # load-time parameters for Radio channels, so that the driver may run # by itself, and just act like a generic Zaptel radio interface. # # Unlike the rest of this file, you specify a block of parameters, and # then the channel(s) to which they apply. CTCSS is specified as a frequency # in tenths of hertz, for example 131.8 HZ is specified as 1318. DCS # for receive is specified as the code directly, for example 223. DCS for # transmit is specified as D and then the code, for example D223. # # The hardware supports a "community" CTCSS decoder system that has # arbitrary transmit CTCSS or DCS codes associated with them, unlike # traditional "community" systems that encode the same tone they decode. # # this example is a single tone DCS transmit and receive # # # specify the transmit tone (in DCS mode this stays constant) # tx=D371 # # specify the receive DCS code # dcsrx=223 # # this example is a "community" CTCSS (if you only want a single tone, then # only specify 1 in the ctcss list) # # # specify the default transmit tone (when not receiving) # tx=1000 # # Specify the receive freq, the tag (use 0 if none), and the transmit code. # # The tag may be used by applications to determine classification of tones. # # The tones are to be specified in order of presedence, most important first. # # Currently, 15 tones may be specified.. # ctcss=1318,1,1318 # ctcss=1862,1,1862 # # The following parameters may be omitted if their default value is acceptible # # # set the receive debounce time in milliseconds # debouncetime=123 # # set the transmit quiet dropoff burst time in milliseconds # bursttime=234 # # set the COR level threshold (specified in tenths of millivolts) # # valid values are {3125,6250,9375,12500,15625,18750,21875,25000} # corthresh=12500 # # Invert COR signal {y,n} # invertcor=y # # set the external tone mode; yes, no, internal {y,n,i} # exttone=y # # Now apply the configuration to the specified channels: # # # We are all done with our channel parameters, so now we specify what # # channels they apply to # channels=1-4