Welcome, this is GNU/HaRET running on WindowsCE v5.2
PLATFORMTYPE: PocketPC
OEMINFO: PU10
Minimal virtual address: 00010000, maximal virtual address: 7fffffff
CPU is Intel ARM arch 5TE revision 0 product 17 stepping 7 running in system mode
Enter 'HELP' for a short command summary.

-----------------
FB1: form=1 bpp=16 fbaddr=A87AA000/A3FAA000 x=480/2 y=640/960
FB0: form=160 bpp=16 fbaddr=B0094020/A0094020 x=240/480 y=320/480
HaRET(1)# dump pxa27xusb
  USB host revision   :                 10
  USB host comm. area :                 0xa0014000
  USB host PCED       :                 0x00000000
  USB host CHED       :                 0x00000000
  USB host CCED       :                 0x00000000
  USB host BHED       :                 0x00000000
  USB host BCED       :                 0x00000000
  USB host DHEAD      :                 0x00000000
  USB host UHCFMN16bit:                 0x00002519
  UHCRHDA  : 0x04000802 = 00000100 00000000 00001000 00000010  (Page 0)
    - :       number of ports          44
  UHCRHPS1 : 0x00000000 = 00000000 00000000 00000000 00000000  (Page 0)
  USB host RHPS1: speed (if currconnect) full
  USB host RHPS1: power                  off
  USB host RHPS1: current                ok
  USB host RHPS1: suspend                off
  USB host RHPS1: enabled                no
  USB host RHPS1: device connected       no
  UHCRHPS2 : 0x00000000 = 00000000 00000000 00000000 00000000  (Page 0)
  USB host RHPS2: speed (if currconnect) full
  USB host RHPS2: power                  off
  USB host RHPS2: current                ok
  USB host RHPS2: suspend                off
  USB host RHPS2: enabled                no
  USB host RHPS2: device connected       no
  UHCRHPS3 : 0x00000000 = 00000000 00000000 00000000 00000000  (Page 0)
  USB host RHPS3: speed (if currconnect) full
  USB host RHPS3: power                  off
  USB host RHPS3: current                ok
  USB host RHPS3: suspend                off
  USB host RHPS3: enabled                no
  USB host RHPS3: device connected       no
  UDCCR    : 0x00000003 = 00000000 00000000 00000000 00000011  (Page 0)
  UDC control :  OTG enable no
  UDC control :  A-dev host alt. neg. proto. enable no
  UDC control :  A-dev host neg. proto. enable no
  UDC control :  B-dev host neg. proto. enable no
  UDC control :  remote wakeup no
  UDC control :   Active     Configuration  Number=   0
  UDC control :   Active     Interface      Number=   0
  UDC control :   Active Alt Iinerface Set. Number= 0
  UDC control :  active yes
  UDC control :  enabled yes
  UP2OCR   : 0x000200a0 = 00000000 00000010 00000000 10100000  (Page 0)
  UP2OCR output : on-chip host transceiver     on
  UP2OCR output : output signals from          device
  UP2OCR output : select off
  UP2OCR output : OTG ID read enable           off
  UP2OCR output : D- pull up bypass            on
  UP2OCR output : D+ pull up bypass            off
  UP2OCR output : D- pull up                   on
  UP2OCR output : D+ pull up                   off
  UP2OCR output : D- pull down                 off
  UP2OCR output : D+ pull down                 off
  UP3OCR   : 0x00000000 = 00000000 00000000 00000000 00000000  (Page 0)
  UHCHR    : 0x00000004 = 00000000 00000000 00000000 00000100  (Page 0)
  UHCHR : SSEP3            off
  UHCHR : SSEP2            off
  UHCHR : SSEP1            off
  UHCHR : PCPL             off
  UHCHR : PSPL             off
  UHCHR : SSE             off
  UHCHR : UIT             off
  UHCHR : SSDS             off
  UHCHR : CGR             on
  UHCHR : FHR             off
  UHCHR : FSBIR             off