Linux version 2.6.14-gentoo-r5 (root@komputer) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #5 PREEMPT Mon Feb 13 04:17:59 PST 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000023ff0000 (usable) BIOS-e820: 0000000023ff0000 - 0000000023ff3000 (ACPI NVS) BIOS-e820: 0000000023ff3000 - 0000000024000000 (ACPI data) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 575MB LOWMEM available. On node 0 totalpages: 147440 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 143344 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 VT8371 ) @ 0x000f7ce0 ACPI: RSDT (v001 VT8371 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x23ff3000 ACPI: FADT (v001 VT8371 AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x23ff3040 ACPI: DSDT (v001 VT8371 AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000 Allocating PCI resources starting at 30000000 (gap: 24000000:dbff0000) Built 1 zonelists Kernel command line: root=/dev/hda3 panic=30 Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (01483000) Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 1200.212 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 580072k/589760k available (2601k kernel code, 9180k reserved, 721k data, 180k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 2404.37 BogoMIPS (lpj=4808747) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000020 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. mtrr: v2.0 (20020519) CPU: AMD Athlon(tm) Processor stepping 02 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. ACPI: setting ELCR to 0200 (from 1e20) NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfb430, last bus=1 PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 PCI quirk: region 6000-607f claimed by vt82c868 HW-mon PCI quirk: region 5000-500f claimed by vt82c868 SMB Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 11 *12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 11 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: e0000000-e1ffffff PREFETCH window: d0000000-dfffffff PCI: Setting latency timer of device 0000:00:01.0 to 64 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1140444570.464:1): initialized Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Applying VIA southbridge workaround. PCI: Disabling Via external APIC routing lp: driver loaded but no devices found ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport_pc: VIA 686A/8231 detected parport_pc: probing current configuration parport_pc: Current parallel port base: 0x378 parport0: PC-style at 0x378, irq 7 [PCSPP(,...)] lp0: using parport0 (interrupt-driven). parport_pc: VIA parallel port: io=0x378, irq=7 mice: PS/2 mouse device common for all mice io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Linux Tulip driver version 1.1.13 (May 11, 2002) ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 tulip0: MII transceiver #1 config 1000 status 786d advertising 05e1. eth0: ADMtek Comet rev 17 at 0001d400, 00:0C:41:F1:8C:BC, IRQ 10. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:07.1 PCI: Via IRQ fixup for 0000:00:07.1, from 255 to 0 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1 ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... input: AT Translated Set 2 keyboard on isa0060/serio0 hda: Maxtor 6L100P0, ATA DISK drive hdb: Maxtor 5T030H3, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: DVD-ROM DDU1622, ATAPI CD/DVD-ROM drive hdd: SONY DVD RW DRU-800A, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 195813072 sectors (100256 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(33) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hdb: max request size: 128KiB hdb: 60030432 sectors (30735 MB) w/2048KiB Cache, CHS=59554/16/63, UDMA(33) hdb: cache flushes not supported hdb: hdb1 hdb2 hdb3 hdc: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) libata version 1.12 loaded. usbmon: debugfs is not available USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 5, io base 0x0000c400 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:07.3: UHCI Host Controller uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:07.3: irq 5, io base 0x0000c800 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usb 1-2: new low speed USB device using uhci_hcd and address 2 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. input: USB HID v1.10 Mouse [B16_b_02 USB-PS/2 Optical Mouse] on usb-0000:00:07.2-2 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver i2c /dev entries driver oprofile: using timer interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered ip_conntrack version 2.3 (4607 buckets, 36856 max) - 216 bytes per conntrack ip_tables: (C) 2000-2002 Netfilter core team ipt_recent v0.3.1: Stephen Frost . http://snowman.net/projects/ipt_recent/ arp_tables: (C) 2002 David S. Miller TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. EXT3-fs: hda3: orphan cleanup on readonly fs ext3_orphan_cleanup: deleting unreferenced inode 265768 ext3_orphan_cleanup: deleting unreferenced inode 266152 ext3_orphan_cleanup: deleting unreferenced inode 266153 ext3_orphan_cleanup: deleting unreferenced inode 266154 ext3_orphan_cleanup: deleting unreferenced inode 266155 ext3_orphan_cleanup: deleting unreferenced inode 264974 EXT3-fs: hda3: 6 orphan inodes deleted EXT3-fs: recovery complete. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 180k freed Adding 241912k swap on /dev/hda2. Priority:-1 extents:1 across:241912k EXT3 FS on hda3, internal journal ndiswrapper version 1.8 loaded (preempt=yes,smp=no) ndiswrapper: driver rt2500 (Ralink Technology, Inc.,04/21/2005, 3.00.03.0000) loaded ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 ndiswrapper: using irq 11 wlan0: vendor: 'IEEE 802.11g Wireless Card.' wlan0: ndiswrapper ethernet device 00:0f:66:f3:d4:0c using driver rt2500, 1814:0201.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK Linux agpgart interface v0.101 (c) Dave Jones ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 12 PCI: setting IRQ 12 as level-triggered ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 12 (level, low) -> IRQ 12 NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-8178 Wed Dec 14 16:22:51 PST 2005 kjournald starting. Commit interval 5 seconds EXT3 FS on hda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5 ndiswrapper (iw_set_tx_power:450): setting tx_power failed (C0010015) ndiswrapper (set_infra_mode:197): setting operating mode failed (C0010015) UDP: bad checksum. From 203.213.205.129:49153 to 192.168.0.7:49513 ulen 50