[ mike in ~ ]$ ifconfig -a -bash: ifconfig: command not found [ mike in ~ ]$ sudo ifconfig -a eth0 Link encap:Ethernet HWaddr 00:04:5A:47:1A:58 inet addr:66.177.39.88 Bcast:255.255.255.255 Mask:255.255.248.0 UP BROADCAST RUNNING MULTICAST MTU:576 Metric:1 RX packets:36704 errors:0 dropped:0 overruns:0 frame:0 TX packets:5181 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:5597316 (5.3 Mb) TX bytes:553411 (540.4 Kb) Interrupt:21 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:2 errors:0 dropped:0 overruns:0 frame:0 TX packets:2 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:100 (100.0 b) TX bytes:100 (100.0 b) [ mike in ~ ]$ dmesg Linux version 2.6.20-fw5 (fst@i686.frugalware.org) (gcc version 4.1.2) #1 SMP PREEMPT Sat Mar 24 14:54:20 CET 2007 BIOS-provided physical RAM map: sanitize start sanitize end copy_e820_map() start: 0000000000000000 size: 000000000009f000 end: 000000000009f000 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000000009f000 size: 0000000000001000 end: 00000000000a0000 type: 2 copy_e820_map() start: 00000000000f0000 size: 0000000000010000 end: 0000000000100000 type: 2 copy_e820_map() start: 0000000000100000 size: 000000001dde0000 end: 000000001dee0000 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000001dee0000 size: 0000000000003000 end: 000000001dee3000 type: 4 copy_e820_map() start: 000000001dee3000 size: 000000000000d000 end: 000000001def0000 type: 3 copy_e820_map() start: 000000001def0000 size: 0000000000010000 end: 000000001df00000 type: 2 copy_e820_map() start: 000000001e000000 size: 0000000002000000 end: 0000000020000000 type: 2 copy_e820_map() start: 00000000e0000000 size: 0000000010000000 end: 00000000f0000000 type: 2 copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2 copy_e820_map() start: 00000000fee00000 size: 0000000000100000 end: 00000000fef00000 type: 2 copy_e820_map() start: 00000000fefffc00 size: 0000000000000400 end: 00000000ff000000 type: 2 copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2 BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001dee0000 (usable) BIOS-e820: 000000001dee0000 - 000000001dee3000 (ACPI NVS) BIOS-e820: 000000001dee3000 - 000000001def0000 (ACPI data) BIOS-e820: 000000001def0000 - 000000001df00000 (reserved) BIOS-e820: 000000001e000000 - 0000000020000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) BIOS-e820: 00000000fefffc00 - 00000000ff000000 (reserved) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 478MB LOWMEM available. found SMP MP-table at 000f39d0 Entering add_active_range(0, 0, 122592) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 122592 HighMem 122592 -> 122592 early_node_map[1] active PFN ranges 0: 0 -> 122592 On node 0 totalpages: 122592 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 925 pages used for memmap Normal zone: 117571 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap DMI 2.3 present. ACPI: RSDP (v000 Nvidia ) @ 0x000f7b00 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dee3040 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dee30c0 ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dee9540 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1dee9480 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:12 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000) Detected 1808.421 MHz processor. Built 1 zonelists. Total pages: 121635 Kernel command line: root=/dev/hda2 ro quiet vga=791 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 480876k/490368k available (3023k kernel code, 9040k reserved, 1070k data, 316k init, 0k highmem) virtual kernel memory layout: fixmap : 0xfff4f000 - 0xfffff000 ( 704 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xde800000 - 0xff7fe000 ( 527 MB) lowmem : 0xc0000000 - 0xddee0000 ( 478 MB) .init : 0xc0506000 - 0xc0555000 ( 316 kB) .data : 0xc03f3e75 - 0xc04ff6f4 (1070 kB) .text : 0xc0100000 - 0xc03f3e75 (3023 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3618.60 BogoMIPS (lpj=1809304) Security Framework v1.0.0 initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 14k freed ACPI: Core revision 20060707 CPU0: AMD Sempron(tm) Processor 3100+ stepping 02 Total of 1 processors activated (3618.60 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 1 CPUs NET: Registered protocol family 16 EISA bus registered ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on 0:18 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:05.0 0000:00:0d.0: cannot adjust BAR0 (not I/O) 0000:00:0d.0: cannot adjust BAR1 (not I/O) 0000:00:0d.0: cannot adjust BAR2 (not I/O) 0000:00:0d.0: cannot adjust BAR3 (not I/O) PCI: Transparent bridge - 0000:00:10.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 *10 11 14 15) ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15) ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices SCSI subsystem initialized libata version 2.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default pnp: 00:01: ioport range 0x1000-0x107f could not be reserved pnp: 00:01: ioport range 0x1080-0x10ff has been reserved pnp: 00:01: ioport range 0x1400-0x147f has been reserved pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved pnp: 00:01: ioport range 0x1800-0x187f has been reserved pnp: 00:01: ioport range 0x1880-0x18ff has been reserved pnp: 00:01: ioport range 0x2000-0x207f has been reserved pnp: 00:01: ioport range 0x2080-0x20ff has been reserved ieee1394: Initialized config rom entry `ip1394' PCI: Bridge: 0000:00:02.0 IO window: 9000-9fff MEM window: fde00000-fdefffff PREFETCH window: fdd00000-fddfffff PCI: Bridge: 0000:00:03.0 IO window: c000-cfff MEM window: fdc00000-fdcfffff PREFETCH window: fdb00000-fdbfffff PCI: Bridge: 0000:00:04.0 IO window: a000-afff MEM window: fd800000-fd8fffff PREFETCH window: fd700000-fd7fffff PCI: Bridge: 0000:00:10.0 IO window: b000-bfff MEM window: fda00000-fdafffff PREFETCH window: fd900000-fd9fffff PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:00:03.0 to 64 PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:10.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 196608 bytes) TCP bind hash table entries: 8192 (order: 4, 98304 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1177179392.553:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered 0000:00:0b.1 EHCI: BIOS handoff failed (BIOS bug ?) 01010001 PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie03] PCI: Setting latency timer of device 0000:00:03.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:03.0:pcie00] Allocate Port Service[0000:00:03.0:pcie03] PCI: Setting latency timer of device 0000:00:04.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:04.0:pcie00] Allocate Port Service[0000:00:04.0:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xd0000000, mapped to 0xde880000, using 3072k, total 32768k vesafb: mode is 1024x768x16, linelength=2048, pages=1 vesafb: protected mode interface info at c000:c350 vesafb: pmi: set display start = c00cc386, set palette = c00cc3f0 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0 NFORCE-MCP51: chipset revision 161 NFORCE-MCP51: not 100% native mode: will probe irqs later NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller ide0: BM-DMA at 0xf400-0xf407, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf408-0xf40f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: ST3100011A, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: LITE-ON DVDRW SHW-1635S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 195371568 sectors (100030 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hda4 hdc: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 sata_nv 0000:00:0e.0: version 3.2 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:0e.0 to 64 ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xE000 irq 16 ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xE008 irq 16 scsi0 : sata_nv ata1: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x9F7 scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300) ATA: abnormal status 0x7F on port 0x977 usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 EISA: Probing bus 0 at eisa.0 Advanced Linux Sound Architecture Driver Version 1.0.14rc1 (Tue Jan 09 09:56:17 2007 UTC). ALSA device list: No soundcards found. TCP bic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI No-Shortcut mode ACPI: (supports S0 S3 S4 S5) Time: tsc clocksource has been installed. input: ImExPS/2 Generic Explorer Mouse as /class/input/input1 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 316k freed EXT3 FS on hda2, internal journal EXT3 FS on hda2, internal journal NTFS driver 2.1.28 [Flags: R/W MODULE]. NTFS volume version 3.1. Adding 1951888k swap on /dev/hda3. Priority:-1 extents:1 across:1951888k parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] lp0: using parport0 (interrupt-driven). lp0: console ready loop: loaded (max 8 devices) Capability LSM initialized Linux agpgart interface v0.101 (c) Dave Jones nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC7] enabled at IRQ 16 ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [APC7] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:05.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9746 Fri Dec 15 09:54:45 PST 2006 QEMU Accelerator Module version 1.3.0, Copyright (c) 2005-2007 Fabrice Bellard KQEMU installed, max_locked_mem=240636kB. ACPI: PCI Interrupt Link [APCL] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 22 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:0b.1 to 64 ehci_hcd 0000:00:0b.1: EHCI Host Controller ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0b.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:0b.1 ehci_hcd 0000:00:0b.1: irq 18, io mem 0xfe02e000 ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected i2c_adapter i2c-0: nForce2 SMBus adapter at 0x1c00 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x1c40 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 21 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:0b.0 to 64 ohci_hcd 0000:00:0b.0: OHCI Host Controller ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0b.0: irq 19, io mem 0xfe02f000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 8 ports detected shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:10.2[C] -> Link [APCJ] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:10.2 to 64 usb 2-2: new full speed USB device using ohci_hcd and address 2 intel8x0_measure_ac97_clock: measured 50683 usecs intel8x0: clocking to 46784 Linux Tulip driver version 1.1.14 (May 11, 2002) ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:04:06.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 21 tulip0: MII transceiver #1 config 1000 status 786d advertising 05e1. eth0: ADMtek Comet rev 17 at MMIO 0xfdaff000, 00:04:5A:47:1A:58, IRQ 21. usb 2-2: configuration #1 chosen from 1 choice hiddev96: USB HID v1.00 Device [Lexmark 2400 Series] on usb-0000:00:0b.0-2 usb 2-5: new full speed USB device using ohci_hcd and address 3 usb 2-5: configuration #1 chosen from 1 choice drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x043D pid 0x00E9 usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3831 buckets, 30648 max) 0000:04:06.0: tulip_stop_rxtx() failed eth0: Setting full-duplex based on MII#1 link partner capability of 41e1. usb-storage: device scan complete scsi 2:0:0:0: Direct-Access Generic USB SD Reader 1.00 PQ: 0 ANSI: 0 scsi 2:0:0:1: Direct-Access Generic USB CF Reader 1.01 PQ: 0 ANSI: 0 scsi 2:0:0:2: Direct-Access Generic USB SM Reader 1.02 PQ: 0 ANSI: 0 scsi 2:0:0:3: Direct-Access Generic USB MS Reader 1.03 PQ: 0 ANSI: 0 sd 2:0:0:0: Attached scsi removable disk sda sd 2:0:0:1: Attached scsi removable disk sdb sd 2:0:0:2: Attached scsi removable disk sdc sd 2:0:0:3: Attached scsi removable disk sdd **WARNING** I2C adapter driver [NVIDIA i2c adapter 0 at 0:05.0] forgot to specify physical device; fix it! **WARNING** I2C adapter driver [NVIDIA i2c adapter 1 at 0:05.0] forgot to specify physical device; fix it! **WARNING** I2C adapter driver [NVIDIA i2c adapter 2 at 0:05.0] forgot to specify physical device; fix it! NET: Registered protocol family 10 lo: Disabled Privacy Extensions forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.