Linux version 2.6.17 (andy@localhost) (gcc version 4.1.1) #1 PREEMPT Fri Apr7 Iomega StorCenter Network Hard Drive Based on the Freescale Sandpoint Development System On node 0 totalpages: 16384 DMA zone: 16384 pages, LIFO batch:3 Built 1 zonelists Kernel command line: root=/dev/mtdblock2 rootfstype=jffs2 rw init=/linuxrc c0 OpenPIC Version 1.2 (1 CPUs and 7 IRQ sources) at fdf40000 OpenPIC timer frequency is 100.000000 MHz PID hash table entries: 512 (order: 9, 2048 bytes) time_init: decrementer frequency = 25.000000 MHz Warning: real time clock seems stuck! Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 62080k available (2200k kernel code, 524k data, 112k init, 0k highme) Calibrating delay loop... 133.12 BogoMIPS (lpj=266240) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware PCI: Adjustments for the VIA VT6410 controller have been made PCI: Cannot allocate resource region 1 of device 0000:00:00.0 Registering openpic with sysfs... SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered NTFS driver 2.1.27 [Flags: R/O]. JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Generic RTC Driver v1.07 Macintosh non-volatile memory driver v1.1 Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 5) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 6) is a 16550A serial8250 serial8250.0: unable to register port at index 0 (IO0 MEMfdf045002 serial8250 serial8250.1: unable to register port at index 0 (IO0 MEMfdf046002 r8169 Gigabit Ethernet driver 2.2LK loaded eth0: Identified chip type is 'RTL8169s/8110s'. eth0: RTL8169 at 0xc5050e00, 00:d0:b8:00:d4:e7, IRQ 0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Found: VIA VT6410 based IDE VP_IDE: IDE controller at PCI slot 0000:00:0d.0 VP_IDE: chipset revision 6 VP_IDE: VIA vt6410 (rev 06) IDE UDMA133 controller on pci0000:00:0d.0 VP_IDE: 100% native mode on irq 1 ide0: BM-DMA at 0xffd0-0xffd7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xffd8-0xffdf, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... hda: ST3250823A, ATA DISK drive ide0 at 0xfff8-0xffff,0xfff6 on irq 1 Probing IDE interface ide1... Probing IDE interface ide1... hda: max request size: 512KiB hda: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63 hda: cache flushes supported hda: hda1 hda2 hda3 hda4 NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ physmap flash device: 800000 at ff800000 phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available ftl_cs: FTL header not found. Iomega8241: Probing for flash... Flash: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Iomega8241: Flash found at location 0xff800000 Creating 4 MTD partitions on "Flash": 0x00000000-0x00170000 : "kernel" ftl_cs: FTL header not found. 0x00170000-0x00700000 : "filesystem" ftl_cs: FTL header not found. 0x00700000-0x00740000 : "bootloader" ftl_cs: FTL header not found. 0x00740000-0x00800000 : "sysconfig" ftl_cs: FTL header not found. Generic platform RAM MTD, (c) 2004 Simtec Electronics ehci_hcd 0000:00:0e.2: EHCI Host Controller ehci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0e.2: irq 4, io mem 0xbfffdf00 ehci_hcd 0000:00:0e.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd 0000:00:0e.0: OHCI Host Controller ohci_hcd 0000:00:0e.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:0e.0: irq 2, io mem 0xbffff000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected ohci_hcd 0000:00:0e.1: OHCI Host Controller ohci_hcd 0000:00:0e.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:0e.1: irq 3, io mem 0xbfffe000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays.