runner X11 # dmesg 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 990 pages used for memmap Normal zone: 125842 pages, LIFO batch:31 DMI present. ACPI: RSDP (v002 IBM ) @ 0x000f7010 ACPI: XSDT (v001 IBM TP-1I 0x00002080 LTP 0x00000000) @ 0x1ff731cd ACPI: FADT (v001 IBM TP-1I 0x00002080 IBM 0x00000001) @ 0x1ff73300 ACPI: SSDT (v001 IBM TP-1I 0x00002080 MSFT 0x0100000d) @ 0x1ff733b4 ACPI: ECDT (v001 IBM TP-1I 0x00002080 IBM 0x00000001) @ 0x1ff7debc ACPI: TCPA (v001 IBM TP-1I 0x00002080 PTL 0x00000001) @ 0x1ff7df0e ACPI: BOOT (v001 IBM TP-1I 0x00002080 LTP 0x00000001) @ 0x1ff7dfd8 ACPI: DSDT (v001 IBM TP-1I 0x00002080 MSFT 0x0100000d) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 Allocating PCI resources starting at 30000000 (gap: 20000000:df800000) Detected 1993.633 MHz processor. Built 1 zonelists. Total pages: 129906 Kernel command line: root=/dev/hda3 quiet resume2=swap:/dev/hda5 video=vesafb Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 514452k/523712k available (2809k kernel code, 8672k reserved, 855k data, 156k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffff8000 - 0xfffff000 ( 28 kB) vmalloc : 0xe0800000 - 0xffff6000 ( 503 MB) lowmem : 0xc0000000 - 0xdff70000 ( 511 MB) .init : 0xc0498000 - 0xc04bf000 ( 156 kB) .data : 0xc03be545 - 0xc04944cc ( 855 kB) .text : 0xc0100000 - 0xc03be545 (2809 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3990.44 BogoMIPS (lpj=7980889) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebf9ff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K CPU: After all inits, caps: bfebf9ff 00000000 00000000 00003080 00004400 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available Compat vDSO mapped to ffffe000. CPU: Intel Mobile Intel(R) Pentium(R) 4 - M CPU 2.00GHz stepping 07 Checking 'hlt' instruction... OK. ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0800) NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfd8fe, last bus=8 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11) *0, disabled. ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH4 GPIO Boot video device is 0000:01:00.0 PCI: Firmware left 0000:02:08.0 e100 interrupts enabled, disabling PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Power Resource [PUBS] (on) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices SCSI subsystem initialized PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:01.0 IO window: 3000-3fff MEM window: d0100000-d01fffff PREFETCH window: e8000000-efffffff PCI: Bus 3, cardbus bridge: 0000:02:00.0 IO window: 00004000-000040ff IO window: 00004400-000044ff PREFETCH window: f0000000-f3ffffff MEM window: d4000000-d7ffffff PCI: Bus 7, cardbus bridge: 0000:02:00.1 IO window: 00004800-000048ff IO window: 00004c00-00004cff PREFETCH window: f4000000-f7ffffff MEM window: d8000000-dbffffff PCI: Bridge: 0000:00:1e.0 IO window: 4000-8fff MEM window: d0200000-dfffffff PREFETCH window: f0000000-f80fffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI Interrupt 0000:02:00.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd Freeing initrd memory: 89k freed Simple Boot Flag at 0x35 set to 0x1 Machine check exception polling timer started. speedstep: frequency transition measured seems out of range (0 nSec), falling back to a safe one of 500000 nSec. squashfs: version 3.2 (2007/01/02) Phillip Lougher Installing knfsd (copyright (C) 1996 okir@monad.swb.de). SGI XFS with ACLs, security attributes, realtime, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel i845 Chipset. agpgart: AGP aperture is 64M @ 0xe0000000 [drm] Initialized drm 1.1.0 20060810 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [drm] Initialized radeon 1.25.0 20060524 on minor 0 vesafb: ATI Technologies Inc., P7 , 01.00 (OEM: ATI MOBILITY RADEON 7500) vesafb: VBE version: 2.0 vesafb: protected mode interface info at c000:5701 vesafb: pmi: set display start = c00c5795, set palette = c00c57e1 vesafb: pmi: ports = 3010 3016 3054 3038 303c 305c 3000 3004 30b0 30b2 30b4 vesafb: no monitor limits have been set vesafb: scrolling: redraw Console: switching to colour frame buffer device 128x48 vesafb: framebuffer at 0xe8000000, mapped to 0xe0880000, using 11484k, total 16320k fb0: VESA VGA frame buffer device Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled pnp: Device 00:0a activated. 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a NS16550A ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt for device 0000:00:1f.6 disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH3M: IDE controller at PCI slot 0000:00:1f.1 PCI: Enabling device 0000:00:1f.1 (0005 -> 0007) ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 ICH3M: chipset revision 2 ICH3M: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: SAMSUNG MP0804H, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-STCD-RW/DVD DRIVE GCC-4160N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 512KiB hda: 156368016 sectors (80060 MB) w/8192KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' ieee80211_crypt: registered algorithm 'CCMP' ieee80211_crypt: registered algorithm 'TKIP' Using IPI Shortcut mode input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: (supports S0 S3 S4 S5) Time: tsc clocksource has been installed. RAMDISK: Couldn't find valid RAM disk image starting at 0. ReiserFS: hda3: found reiserfs format "3.6" with standard journal ReiserFS: hda3: using ordered data mode ReiserFS: hda3: journal params: device hda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hda3: checking transaction log (hda3) ReiserFS: hda3: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 156k freed usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 11, io base 0x00001800 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 11, io base 0x00001820 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 11, io base 0x00001840 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.6 to 64 PCI: Unable to reserve mem region #1:8000000@e8000000 for device 0000:01:00.0 radeonfb (0000:01:00.0): cannot request region 0. radeonfb: probe of 0000:01:00.0 failed with error -16 ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.5 to 64 e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation intel_rng: FWH not detected intel8x0_measure_ac97_clock: measured 55138 usecs intel8x0: clocking to 48000 Yenta: CardBus bridge found at 0000:02:00.0 [1014:0512] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.0, mfunc 0x01d21022, devctl 0x64 NET: Registered protocol family 23 parport: PnPBIOS parport detected. parport0: PC-style at 0x3bc, irq 7 [PCSPP,TRISTATE] Synaptics Touchpad, model: 1, fw: 5.9, id: 0x2c6ab1, caps: 0x884793/0x0 serio: Synaptics pass-through port at isa0060/serio1/input0 Yenta: ISA IRQ mask 0x0438, PCI irq 11 Socket status: 30000006 pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xdfffffff pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf80fffff Yenta: CardBus bridge found at 0000:02:00.1 [1014:0512] Yenta: Using INTVAL to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:02:00.1, mfunc 0x01d21022, devctl 0x64 input: SynPS/2 Synaptics TouchPad as /class/input/input1 pnp: Device 00:0c activated. nsc-ircc, chip->init nsc-ircc, Found chip at base=0x02e nsc-ircc, driver loaded (Dag Brattli) IrDA: Registered device irda0 nsc-ircc, Found dongle: HP HSDL-1100/HSDL-2100 Yenta: ISA IRQ mask 0x0438, PCI irq 11 Socket status: 30000020 pcmcia: parent PCI bridge I/O window: 0x4000 - 0x8fff pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xdfffffff pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf80fffff ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11 ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11 e100: eth0: e100_probe: addr 0xd0200000, irq 11, MAC addr 00:09:6B:7A:42:9D pccard: CardBus card inserted into slot 1 ath_hal: module license 'Proprietary' taints kernel. ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) wlan: 0.8.4.2 (0.9.3) ath_pci: 0.9.4.5 (0.9.3) PCI: Enabling device 0000:07:00.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:07:00.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 ath_rate_sample: 1.2 (0.9.3) wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP wifi0: mac 7.9 phy 4.5 radio 5.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons wifi0: Atheros 5212: mem=0xd8000000, irq=11 ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) input: Power Button (FF) as /class/input/input2 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input3 ACPI: Lid Switch [LID] input: Sleep Button (CM) as /class/input/input4 ACPI: Sleep Button (CM) [SLPB] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU] (supports 8 throttling states) ACPI: Video Device [VID] (multi-head: yes rom: no post: no) Time: acpi_pm clocksource has been installed. Unable to find swap-space signature IBM TrackPoint firmware: 0x0e, buttons: 3/3 input: TPPS/2 IBM TrackPoint as /class/input/input5 fuse init (API version 7.8) fuse distribution version: 2.6.3 agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V2 device at 0000:00:00.0 into 4x mode agpgart: Putting AGP V2 device at 0000:01:00.0 into 4x mode [drm] Setting GART location based on new memory map [drm] writeback test succeeded in 2 usecs ISO 9660 Extensions: Microsoft Joliet Level 3 ISO 9660 Extensions: RRIP_1991A