ivtv:  ==================== START INIT IVTV ====================
ivtv:  version 0.4.2 (tagged release) loading
ivtv:  Linux version: 2.6.15-gentoo-r1 SMP preempt PENTIUM4 gcc-3.3
ivtv:  In case of problems please include the debug info between
ivtv:  the START INIT IVTV and END INIT IVTV lines, along with
ivtv:  any module options, when mailing the ivtv-users mailinglist.
ivtv0: Autodetected WinTV PVR 250 card (cx23415 based)
ivtv0 info: base addr: 0xe0000000
ivtv0 info: Enabling pci device
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKB] -> GSI 3 (level, low) -> IRQ 3
ivtv0 info: Attempting to enable Bus Mastering
ivtv0 info: Bus Mastering Enabled.
ivtv0 info: 2051 (rev 1) at 00:09.0, irq: 3, latency: 64, memory: 0xe0000000
ivtv0 info: attempting ioremap at 0xe0000000 len 0x00800000
ivtv0 info: attempting ioremap at 0xe1000000 len 0x00800000
ivtv0 info: attempting ioremap at 0xe2000000 len 0x00010000
ivtv0 info: activating i2c...
ivtv0: i2c attach to card #0 ok [client=tveeprom, addr=50]
tuner 0-0061: chip found @ 0xc2 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=(tuner unset), addr=61]
saa7115 0-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
ivtv0: i2c attach to card #0 ok [client=saa7115, addr=21]
msp3400 0-0040: chip=MSP3435G-B6 +nicam +simple +simpler +radio mode=simpler
msp3400 0-0040: msp34xxg daemon started
ivtv0: i2c attach to card #0 ok [client=MSP3435G-B6, addr=40]
ivtv0 info: Active card count: 1.
ivtv0 info: Loaded module tveeprom
tveeprom 0-0050: Hauppauge model 48011, rev G510, serial# 2669773
tveeprom 0-0050: tuner model is Philips FI1236 MK2 (idx 10, type 2)
tveeprom 0-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 0-0050: audio processor is MSP3435 (idx 10)
tveeprom 0-0050: has radio
ivtv0 info: NTSC tuner detected
ivtv0 info: Loaded module tuner
ivtv0 info: Loaded module saa7115
ivtv0 info: Loaded module msp3400
ivtv0 info: Loaded module tda9887
ivtv0 info: Stopping VDM
ivtv0 info: Stopping AO
ivtv0 info: pinging (?) APU
ivtv0 info: Stopping VPU
ivtv0 info: Resetting Hw Blocks
ivtv0 info: Stopping SPU
ivtv0 info: Sleeping for 10ms
ivtv0 info: init Encoder SDRAM pre-charge
ivtv0 info: init Encoder SDRAM refresh to 1us
ivtv0 info: init Decoder SDRAM pre-charge
ivtv0 info: init Decoder SDRAM refresh to 1us
ivtv0 info: Sleeping for 150ms (600 recommended)
ivtv0 info: Card ready for firmware!
ivtv0 info: Loading encoder image
ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv0 info: Loading decoder image
ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
ivtv0 info: Sleeping for 100 ms
ivtv0 info: Sleeping for 100 ms
ivtv0 info: GPIO INIT
ivtv0 info: About to search for mailboxes
ivtv0 info: Searching for encoder mailbox
ivtv0 info: match: 0x34567812 at 0xd0980104. match: 1
ivtv0 info: match: 0x56781234 at 0xd0980108. match: 2
ivtv0 info: match: 0x78123456 at 0xd098010c. match: 3
ivtv0 info: found encoder mailbox!
ivtv0 info: Searching for decoder mailbox
ivtv0 info: match: 0x34567812 at 0xd1200404. match: 1
ivtv0 info: match: 0x56781234 at 0xd1200408. match: 2
ivtv0 info: match: 0x78123456 at 0xd120040c. match: 3
ivtv0 info: found decoder mailbox!
ivtv0 info: Getting firmware version..
ivtv0 info: Getting encoder firmware rev.
ivtv0: Encoder revision: 0x02050032
ivtv0 info: Getting decoder firmware rev.
ivtv0: Decoder revision: 0x02020023
ivtv0 info: v4l2 streams setup
ivtv0 info: Configuring WinTV PVR 250 card with 5 streams
ivtv0 info: Registered v4l2 device for encoder MPEG minor 0
ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv0 info: Registered v4l2 device for encoder YUV minor 32
ivtv0: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv0 info: Registered v4l2 device for encoder VBI minor 224
ivtv0: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv0 info: Registered v4l2 device for encoder PCM audio minor 24
ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv0 info: Registered v4l2 device for encoder radio minor 64
ivtv0: Create encoder radio stream
ivtv0 info: Allocate encoder radio stream
ivtv0 info: Starting Threads
tuner 0-0061: type set to 2 (Philips NTSC (FI1236,FM1236 and compatibles))
ivtv0 info: ivtv_enc_thread: pid = 13765, itv = 0xc3750000
ivtv0 info: encoder thread sleeping 13765
ivtv0 info: ivtv_enc_vbi_thread: pid = 13766, itv = 0xc3750000
ivtv0 info: encoder thread sleeping 13766
ivtv0 info: Setting audio to input 0
ivtv0 info: Setting audio matrix to input 3, output 1
ivtv0 info: Switching standard to NTSC.
ivtv0 info: Disabling digitizer
ivtv0 info: v4l2 ioctl: set frequency 1076
ivtv0 info: Enabling digitizer
ivtv0 info: Finished with Mute
ivtv0: Initialized WinTV PVR 250, card #0
ivtv:  ======================  NEXT CARD  ======================
ivtv1: Autodetected WinTV PVR 150 card (cx23416 based)
ivtv1 info: base addr: 0xe4000000
ivtv1 info: Enabling pci device
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
ivtv1 info: Attempting to enable Bus Mastering
ivtv1 info: Bus Mastering Enabled.
ivtv1 info: 22 (rev 1) at 00:0a.0, irq: 5, latency: 64, memory: 0xe4000000
ivtv1 info: attempting ioremap at 0xe4000000 len 0x00800000
ivtv1 info: attempting ioremap at 0xe5000000 len 0x00800000
ivtv1 info: attempting ioremap at 0xe6000000 len 0x00010000
ivtv1 info: activating i2c...
ivtv1: i2c attach to card #1 ok [client=tveeprom, addr=50]
tuner 1-0061: chip found @ 0xc2 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=(tuner unset), addr=61]
tda9887 1-0043: chip found @ 0x86 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=tda9887, addr=43]
cx25840 1-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #1)
cx25840 1-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv1: i2c attach to card #1 ok [client=cx25840, addr=44]
wm8775 1-001b: chip found @ 0x36 (ivtv i2c driver #1)
ivtv1: i2c attach to card #1 ok [client=wm8775, addr=1b]
ivtv1 info: Active card count: 2.
ivtv1 info: Loaded module tveeprom
tveeprom 1-0050: The eeprom says no radio is present, but the tuner type
tveeprom 1-0050: indicates otherwise. I will assume that radio is present.
tveeprom 1-0050: Hauppauge model 26552, rev C268, serial# 8227649
tveeprom 1-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
tveeprom 1-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 1-0050: audio processor is CX25843 (idx 37)
tveeprom 1-0050: decoder processor is CX25843 (idx 30)
tveeprom 1-0050: has radio, has no IR remote
ivtv1 info: Loaded module tuner
ivtv1 info: Loaded module cx25840
ivtv1 info: Loaded module wm8775
ivtv1 info: Loaded module tda9887
ivtv1 info: Stopping VDM
ivtv1 info: Stopping AO
ivtv1 info: pinging (?) APU
ivtv1 info: Stopping VPU
ivtv1 info: Resetting Hw Blocks
ivtv1 info: Stopping SPU
ivtv1 info: Sleeping for 10ms
ivtv1 info: init Encoder SDRAM pre-charge
ivtv1 info: init Encoder SDRAM refresh to 1us
ivtv1 info: init Decoder SDRAM pre-charge
ivtv1 info: init Decoder SDRAM refresh to 1us
ivtv1 info: Sleeping for 150ms (600 recommended)
ivtv1 info: Card ready for firmware!
ivtv1 info: Loading encoder image
ivtv1: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv1 info: Sleeping for 100 ms
ivtv1 info: Sleeping for 100 ms
ivtv1 info: GPIO INIT
ivtv1 info: About to search for mailboxes
ivtv1 info: Searching for encoder mailbox
ivtv1 info: match: 0x34567812 at 0xd1a80104. match: 1
ivtv1 info: match: 0x56781234 at 0xd1a80108. match: 2
ivtv1 info: match: 0x78123456 at 0xd1a8010c. match: 3
ivtv1 info: found encoder mailbox!
ivtv1 info: Searching for decoder mailbox
ivtv1 info: match: 0x34567812 at 0xd2300104. match: 1
ivtv1 info: match: 0x56781234 at 0xd2300108. match: 2
ivtv1 info: match: 0x78123456 at 0xd230010c. match: 3
ivtv1 info: found decoder mailbox!
ivtv1 info: Getting firmware version..
ivtv1 info: Getting encoder firmware rev.
ivtv1: Encoder revision: 0x02050032
ivtv1 info: v4l2 streams setup
ivtv1 info: Configuring WinTV PVR 150 card with 5 streams
ivtv1 info: Registered v4l2 device for encoder MPEG minor 1
ivtv1: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv1 info: Registered v4l2 device for encoder YUV minor 33
ivtv1: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv1 info: Registered v4l2 device for encoder VBI minor 225
ivtv1: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv1 info: Registered v4l2 device for encoder PCM audio minor 25
ivtv1: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv1 info: Registered v4l2 device for encoder radio minor 65
ivtv1: Create encoder radio stream
ivtv1 info: Allocate encoder radio stream
ivtv1 info: Starting Threads
tuner 1-0061: type set to 47 (LG NTSC (TAPE series))
ivtv1 info: ivtv_enc_thread: pid = 13837, itv = 0xc5560000
ivtv1 info: encoder thread sleeping 13837
ivtv1 info: ivtv_enc_vbi_thread: pid = 13838, itv = 0xc5560000
ivtv1 info: encoder thread sleeping 13838
ivtv1 info: Setting audio to input 0
ivtv1 info: Switching standard to NTSC.
ivtv1 info: Disabling digitizer
ivtv1 info: v4l2 ioctl: set frequency 1076
ivtv1 info: Enabling digitizer
ivtv1 info: Finished with Mute
ivtv1: Initialized WinTV PVR 150, card #1
ivtv:  ======================  NEXT CARD  ======================
ivtv2: Autodetected WinTV PVR 150 card (cx23416 based)
ivtv2 info: base addr: 0xe8000000
ivtv2 info: Enabling pci device
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
ivtv2 info: Attempting to enable Bus Mastering
ivtv2 info: Bus Mastering Enabled.
ivtv2 info: 22 (rev 1) at 00:0b.0, irq: 10, latency: 64, memory: 0xe8000000
ivtv2 info: attempting ioremap at 0xe8000000 len 0x00800000
ivtv2 info: attempting ioremap at 0xe9000000 len 0x00800000
ivtv2 info: attempting ioremap at 0xea000000 len 0x00010000
ivtv2 info: activating i2c...
ivtv2: i2c attach to card #2 ok [client=tveeprom, addr=50]
tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #2)
ivtv2: i2c attach to card #2 ok [client=(tuner unset), addr=61]
tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #2)
ivtv2: i2c attach to card #2 ok [client=tda9887, addr=43]
cx25840 2-0044: cx25843-23 found @ 0x88 (ivtv i2c driver #2)
cx25840 2-0044: loaded v4l-cx25840.fw firmware (14264 bytes)
ivtv2: i2c attach to card #2 ok [client=cx25840, addr=44]
wm8775 2-001b: chip found @ 0x36 (ivtv i2c driver #2)
ivtv2: i2c attach to card #2 ok [client=wm8775, addr=1b]
ivtv2 info: Active card count: 3.
ivtv2 info: Loaded module tveeprom
tveeprom 2-0050: The eeprom says no radio is present, but the tuner type
tveeprom 2-0050: indicates otherwise. I will assume that radio is present.
tveeprom 2-0050: Hauppauge model 26552, rev C268, serial# 8227643
tveeprom 2-0050: tuner model is LG TAPE H001F MK3 (idx 68, type 47)
tveeprom 2-0050: TV standards NTSC(M) (eeprom 0x08)
tveeprom 2-0050: audio processor is CX25843 (idx 37)
tveeprom 2-0050: decoder processor is CX25843 (idx 30)
tveeprom 2-0050: has radio, has no IR remote
ivtv2 info: Loaded module tuner
ivtv2 info: Loaded module cx25840
ivtv2 info: Loaded module wm8775
ivtv2 info: Loaded module tda9887
ivtv2 info: Stopping VDM
ivtv2 info: Stopping AO
ivtv2 info: pinging (?) APU
ivtv2 info: Stopping VPU
ivtv2 info: Resetting Hw Blocks
ivtv2 info: Stopping SPU
ivtv2 info: Sleeping for 10ms
ivtv2 info: init Encoder SDRAM pre-charge
ivtv2 info: init Encoder SDRAM refresh to 1us
ivtv2 info: init Decoder SDRAM pre-charge
ivtv2 info: init Decoder SDRAM refresh to 1us
ivtv2 info: Sleeping for 150ms (600 recommended)
ivtv2 info: Card ready for firmware!
ivtv2 info: Loading encoder image
ivtv2: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
ivtv2 info: Sleeping for 100 ms
ivtv2 info: Sleeping for 100 ms
ivtv2 info: GPIO INIT
ivtv2 info: About to search for mailboxes
ivtv2 info: Searching for encoder mailbox
ivtv2 info: match: 0x34567812 at 0xd2b80104. match: 1
ivtv2 info: match: 0x56781234 at 0xd2b80108. match: 2
ivtv2 info: match: 0x78123456 at 0xd2b8010c. match: 3
ivtv2 info: found encoder mailbox!
ivtv2 info: Searching for decoder mailbox
ivtv2 info: match: 0x34567812 at 0xd3400104. match: 1
ivtv2 info: match: 0x56781234 at 0xd3400108. match: 2
ivtv2 info: match: 0x78123456 at 0xd340010c. match: 3
ivtv2 info: found decoder mailbox!
ivtv2 info: Getting firmware version..
ivtv2 info: Getting encoder firmware rev.
ivtv2: Encoder revision: 0x02050032
ivtv2 info: v4l2 streams setup
ivtv2 info: Configuring WinTV PVR 150 card with 5 streams
ivtv2 info: Registered v4l2 device for encoder MPEG minor 2
ivtv2: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
ivtv2 info: Registered v4l2 device for encoder YUV minor 34
ivtv2: Allocate DMA encoder YUV stream: 194 x 10800 buffers (2048KB total)
ivtv2 info: Registered v4l2 device for encoder VBI minor 226
ivtv2: Allocate DMA encoder VBI stream: 120 x 17472 buffers (2048KB total)
ivtv2 info: Registered v4l2 device for encoder PCM audio minor 26
ivtv2: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
ivtv2 info: Registered v4l2 device for encoder radio minor 66
ivtv2: Create encoder radio stream
ivtv2 info: Allocate encoder radio stream
ivtv2 info: Starting Threads
tuner 2-0061: type set to 47 (LG NTSC (TAPE series))
ivtv2 info: ivtv_enc_thread: pid = 13919, itv = 0xc3c30000
ivtv2 info: encoder thread sleeping 13919
ivtv2 info: ivtv_enc_vbi_thread: pid = 13920, itv = 0xc3c30000
ivtv2 info: encoder thread sleeping 13920
ivtv2 info: Setting audio to input 0
ivtv2 info: Switching standard to NTSC.
ivtv2 info: Disabling digitizer
ivtv2 info: v4l2 ioctl: set frequency 1076
ivtv2 info: Enabling digitizer
ivtv2 info: Finished with Mute
ivtv2: Initialized WinTV PVR 150, card #2
ivtv:  ====================  END INIT IVTV  ====================