Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 PCI: VIA IRQ fixup for 0000:00:0f.1, from 255 to 4 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio Probing IDE interface ide0... Probing IDE interface ide0... Probing IDE interface ide1... libata version 2.00 loaded. sata_via 0000:00:0f.0: version 2.0 sata_via 0000:00:0f.0: routed to hard irq line 11 ata1: SATA max UDMA/133 cmd 0xF800 ctl 0xF402 bmdma 0xE800 irq 20 ata2: SATA max UDMA/133 cmd 0xF000 ctl 0xEC02 bmdma 0xE808 irq 20 scsi0 : sata_via ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-7, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32) ata1.00: ata1: dev 0 multi count 16 ata1.00: configured for UDMA/133 scsi1 : sata_via ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata2.00: ATA-7, max UDMA/133, 312581808 sectors: LBA48 NCQ (depth 0/32) ata2.00: ata2: dev 0 multi count 16 ata2.00: configured for UDMA/133 Vendor: ATA Model: ST3160812AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 05 Vendor: ATA Model: ST3160812AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 sd 0:0:0:0: Attached scsi disk sda SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sd 1:0:0:0: Attached scsi disk sdb sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice i2c /dev entries driver hwmon-vid: Unknown VRM version of your x86 CPU md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: multipath personality registered for level -4 md: faulty personality registered for level -5 md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com EDAC MC: Ver: 2.0.1 Oct 15 2006 EDAC DEBUG: edac_sysfs_memctrl_setup() EDAC DEBUG: Registered '.../edac/mc' kobject EDAC DEBUG: edac_sysfs_pci_setup() EDAC DEBUG: Registered '.../edac/pci' kobject padlock: No VIA PadLock drivers have been loaded. padlock: Using VIA PadLock ACE for AES algorithm. padlock: Fallback for 'sha1' is driver 'sha1-generic' (prio=0) padlock: Fallback for 'sha256' is driver 'sha256-generic' (prio=0) padlock: Using VIA PadLock ACE for SHA1/SHA256 algorithms. TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 802.1Q VLAN Support v1.8 Ben Greear All bugs added by David S. Miller Using IPI Shortcut mode drivers/rtc/hctosys.c: unable to open rtc device (rtc0) md: Autodetecting RAID arrays. Time: tsc clocksource has been installed. md: autorun ... md: considering sdb1 ... md: adding sdb1 ... md: adding sda4 ... md: created md0 md: bind md: bind md: running: md0: setting max_sectors to 128, segment boundary to 32767 raid0: looking at sdb1 raid0: comparing sdb1(128536000) with sdb1(128536000) raid0: END raid0: ==> UNIQUE raid0: 1 zones raid0: looking at sda4 raid0: comparing sda4(128536000) with sdb1(128536000) raid0: EQUAL raid0: FINAL 1 zones raid0: done. raid0 : md_size is 257072000 blocks. raid0 : conf->hash_spacing is 257072000 blocks. raid0 : nb_zone is 1. raid0 : Allocating 4 bytes for hash. md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 204k freed EXT2-fs warning: checktime reached, running e2fsck is recommended input: AT Translated Set 2 keyboard as /class/input/input0 Velocity is AUTO mode input: AT Translated Set 2 keyboard as /class/input/input1 eth0: Link autonegation speed 100M bps full duplex w83697hf/hg WDT: WDT driver for W83697HF/HG initializing w83697hf/hg WDT: Looking for watchdog at address 0x4e w83697hf/hg WDT: watchdog found at address 0x4e w83697hf/hg WDT: initialized. timeout=60 sec (nowayout=0) ReiserFS: sda3: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda3 kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. ReiserFS: sda1: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sda1 kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. ReiserFS: sdb2: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on sdb2 kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal EXT3-fs: mounted filesystem with ordered data mode. ReiserFS: md0: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on md0 kjournald starting. Commit interval 5 seconds EXT3 FS on md0, internal journal EXT3-fs: mounted filesystem with ordered data mode.