eas@Ploutonas:~$ modinfo bttv
filename:       /lib/modules/2.6.20-15-generic/kernel/drivers/media/video/bt8xx/bttv.ko
license:        GPL
author:         Ralph Metzler & Marcus Metzler & Gerd Knorr
description:    bttv - v4l/v4l2 driver module for bt848/878 based cards
srcversion:     DB1C6565C3A1D81C944A576
alias:          pci:v0000109Ed0000036Fsv*sd*bc*sc*i*
alias:          pci:v0000109Ed0000036Esv*sd*bc*sc*i*
alias:          pci:v0000109Ed00000351sv*sd*bc*sc*i*
alias:          pci:v0000109Ed00000350sv*sd*bc*sc*i*
depends:        video-buf,i2c-core,ir-common,videodev,tveeprom,v4l2-common,btcx-risc,i2c-algo-bit,compat_ioctl32
vermagic:       2.6.20-15-generic SMP mod_unload 586
parm:           debug:int
parm:           repeat_delay:int
parm:           repeat_period:int
parm:           rc5_remote_gap:int
parm:           rc5_key_timeout:int
parm:           i2c_debug:int
parm:           i2c_hw:configure i2c debug level (int)
parm:           i2c_scan:scan i2c bus at insmod time (int)
parm:           i2c_udelay:soft i2c delay at insmod time, in usecs (should be 5 or higher). Lower value means higher bus speed. (int)
parm:           vbibufs:number of vbi buffers, range 2-32, default 4 (int)
parm:           vbi_debug:vbi code debug messages, default is 0 (no) (int)
parm:           gpiomask:int
parm:           audioall:int
parm:           svhs:array of int
parm:           remote:array of int
parm:           audiomux:array of int
parm:           triton1:set ETBF pci config bit [enable bug compatibility for triton1 + others] (int)
parm:           vsfx:set VSFX pci config bit [yet another chipset flaw workaround] (int)
parm:           latency:pci latency timer (int)
parm:           card:specify TV/grabber card model, see CARDLIST file for a list (array of int)
parm:           pll:specify installed crystal (0=none, 28=28 MHz, 35=35 MHz) (array of int)
parm:           tuner:specify installed tuner type (array of int)
parm:           autoload:automatically load i2c modules like tuner.o, default is 1 (yes) (int)
parm:           no_overlay:allow override overlay default (0 disables, 1 enables) [some VIA/SIS chipsets are known to have problem with overlay] (int)
parm:           debug_latency:int
parm:           fdsr:int
parm:           video_nr:int
parm:           radio_nr:int
parm:           vbi_nr:int
parm:           v4l2:int
parm:           combfilter:int
parm:           lumafilter:int
parm:           radio:The TV card supports radio, default is 0 (no) (array of int)
parm:           bigendian:byte order of the framebuffer, default is native endian (int)
parm:           bttv_verbose:verbose startup messages, default is 1 (yes) (int)
parm:           bttv_gpio:log gpio changes, default is 0 (no) (int)
parm:           bttv_debug:debug messages, default is 0 (no) (int)
parm:           irq_debug:irq handler debug messages, default is 0 (no) (int)
parm:           gbuffers:number of capture buffers. range 2-32, default 8 (int)
parm:           gbufsize:size of the capture buffers, default is 0x208000 (int)
parm:           automute:mute audio on bad/missing video signal, default is 1 (yes) (int)
parm:           chroma_agc:enables the AGC of chroma signal, default is 0 (no) (int)
parm:           adc_crush:enables the luminance ADC crush, default is 1 (yes) (int)
parm:           whitecrush_upper:sets the white crush upper value, default is 207 (int)
parm:           whitecrush_lower:sets the white crush lower value, default is 127 (int)
parm:           vcr_hack:enables the VCR hack (improves synch on poor VCR tapes), default is 0 (no) (int)
parm:           irq_iswitch:switch inputs in irq handler (int)
parm:           uv_ratio:ratio between u and v gains, default is 50 (int)
parm:           full_luma_range:use the full luma range, default is 0 (no) (int)
parm:           coring:set the luma coring level, default is 0 (no) (int)