artspace:/home/hall# dmesg Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12etch1) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Wed Apr 18 09:55:10 UTC 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001feae000 (usable) BIOS-e820: 000000001feae000 - 0000000020000000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 510MB LOWMEM available. On node 0 totalpages: 130734 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 126638 pages, LIFO batch:31 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000fd790 ACPI: RSDT (v001 DELL GX110 0x00000007 ASL 0x00000061) @ 0x000fd7a4 ACPI: FADT (v001 DELL GX110 0x00000007 ASL 0x00000061) @ 0x000fd7cc ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000b) @ 0x00000000 ACPI: PM-Timer IO Port: 0x808 Allocating PCI resources starting at 30000000 (gap: 20000000:dfb00000) Detected 664.552 MHz processor. Built 1 zonelists. Total pages: 130734 Kernel command line: root=/dev/hda1 ro Local APIC disabled by BIOS -- you can enable it with "lapic" mapped APIC to ffffd000 (0140a000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 510768k/522936k available (1544k kernel code, 11588k reserved, 577k data, 196k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 1330.24 BogoMIPS (lpj=2660483) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000 00000000 00000000 00000000 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 256K CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0e20) CPU0: Intel Pentium III (Coppermine) stepping 03 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs migration_cost=0 checking if image is initramfs... it is Freeing initrd memory: 4401k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfc0be, last bus=1 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:00:01.0 PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0880-08bf claimed by ICH4 GPIO PCI: Firmware left 0000:01:09.0 e100 interrupts enabled, disabling PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices PnPBIOS: Disabled by ACPI PNP PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:0c: ioport range 0x800-0x85f could not be reserved pnp: 00:0c: ioport range 0xc00-0xc7f has been reserved pnp: 00:0c: ioport range 0x860-0x8ff could not be reserved PCI: Ignore bogus resource 6 [0:0] of 0000:00:01.0 PCI: Bridge: 0000:00:1e.0 IO window: e000-efff MEM window: fd000000-feffffff PREFETCH window: f8000000-f80fffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered audit: initializing netlink socket (disabled) audit(1178494825.824:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Using IPI No-Shortcut mode ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 196k freed Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input0 ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707] ACPI: Getting cpuindex for acpiid 0x2 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH: IDE controller at PCI slot 0000:00:1f.1 ICH: chipset revision 2 ICH: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio Probing IDE interface ide0... usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ieee1394: Initialized config rom entry `ip1394' e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI e100: Copyright(c) 1999-2005 Intel Corporation hda: SAMSUNG SP4002H, ATA DISK drive hdb: ExcelStor Technology J240, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:1f.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 PCI: Setting latency timer of device 0000:00:1f.2 to 64 uhci_hcd 0000:00:1f.2: UHCI Host Controller uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000ff80 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hda: max request size: 128KiB hda: 78242976 sectors (40060 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 > hdb: max request size: 128KiB ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 PCI: setting IRQ 5 as level-triggered ACPI: PCI Interrupt 0000:01:09.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 e100: eth0: e100_probe: addr 0xf8000000, irq 5, MAC addr 00:50:8B:5A:3F:E4 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 ohci1394: fw-host0: SelfID received outside of bus reset sequence ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[10] MMIO=[fdfff000-fdfff7ff] Max Packet=[1024] IR/IT contexts=[4/4] ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 0000:01:0c.0: 3Com PCI 3c905C Tornado at e081cc00. hdb: 80418240 sectors (41174 MB) w/1863KiB Cache, CHS=65535/16/63, UDMA(33) hdb: cache flushes supported hdb: hdb1 hdb2 < hdb5 hdb6 > Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c0d00001f7a882] input: PC Speaker as /class/input/input1 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel i810 E Chipset. agpgart: detected 4MB dedicated video ram. agpgart: AGP aperture is 64M @ 0xf4000000 eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) ACPI: PCI Interrupt 0000:00:1f.3[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 i801_smbus 0000:00:1f.3: Enabling SMBus device Intel 82802 RNG detected pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 input: ImPS/2 Generic Wheel Mouse as /class/input/input2 Real Time Clock Driver v1.12ac Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,EPP,ECP] ts: Compaq touchscreen protocol output ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:00:1f.5 to 64 intel8x0_measure_ac97_clock: measured 54700 usecs intel8x0: clocking to 48000 Adding 1389580k swap on /dev/hda5. Priority:-1 extents:1 across:1389580k EXT3 FS on hda1, internal journal loop: loaded (max 8 devices) SCSI subsystem initialized ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3 FS on hda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ACPI: Power Button (FF) [PWRF] lp0: using parport0 (interrupt-driven). ppdev: user-space parallel port driver [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 PCI: setting IRQ 9 as level-triggered ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 9 (level, low) -> IRQ 9 [drm] Initialized i810 1.4.0 20030605 on minor 0 mtrr: base(0xf4000000) is not aligned on a size(0x180000) boundary [drm] Using v1.4 init. end_request: I/O error, dev fd0, sector 0 end_request: I/O error, dev fd0, sector 0 Buffer I/O error on device fd0, logical block 0 end_request: I/O error, dev fd0, sector 0 Buffer I/O error on device fd0, logical block 0 eth1: setting half-duplex. ADDRCONF(NETDEV_UP): eth1: link is not ready ADDRCONF(NETDEV_UP): eth2: link is not ready e100: eth2: e100_watchdog: link up, 100Mbps, full-duplex ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready end_request: I/O error, dev fd0, sector 0 eth2: no IPv6 routers present end_request: I/O error, dev fd0, sector 0 Buffer I/O error on device fd0, logical block 0 end_request: I/O error, dev fd0, sector 0 Buffer I/O error on device fd0, logical block 0 end_request: I/O error, dev fd0, sector 0 end_request: I/O error, dev fd0, sector 0 Buffer I/O error on device fd0, logical block 0 Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon!kjournald starting. Commit interval 5 seconds EXT3 FS on hdb1, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hdb6, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. end_request: I/O error, dev fd0, sector 0 Buffer I/O error on device fd0, logical block 0 eth1: setting half-duplex. ADDRCONF(NETDEV_UP): eth1: link is not ready artspace:/home/hall#