#sho dsl inte Iola_Router#sho dsl interface atm0 ATU-R (DS) ATU-C (US) Modem Status: Showtime (DMTDSL_SHOWTIME) DSL Mode: ITU G.992.2 (G.Lite) ITU STD NUM: 0x01 0x01 Vendor ID: 'ALCB' 'GSPN' Vendor Specific: 0x0000 0x0003 Vendor Country: 0x00 0x00 Capacity Used: 95% 100% Noise Margin: 6.5 dB 4.0 dB Output Power: 17.0 dBm 12.0 dBm Attenuation: 21.0 dB 21.0 dB Defect Status: None None Last Fail Code: None Selftest Result: 0x00 Subfunction: 0x15 Interrupts: 1165339 (2 spurious) Activations: 130 Init FW: embedded Operartion FW: embedded SW Version: 3.9.220 FW Version: 0x1A04 Interleave Fast Interleave Fast Speed (kbps): 3616 0 864 0 Reed-Solomon EC: 0 0 176 0 CRC Errors: 0 0 1 0 Header Errors: 0 0 0 0 Bit Errors: 0 0 BER Valid sec: 0 0 BER Invalid sec: 0 0 LOM Monitoring : Disabled DMT Bits Per Bin 00: 0 0 0 0 0 0 0 8 8 8 A A B B B B 10: B C C C C C C C B A 9 9 9 9 0 0 20: 0 0 0 0 0 0 2 3 4 5 6 6 7 7 7 8 30: 8 9 9 9 A A A A B B B B B C C C 40: 0 C C C C C C C C C C D D D D D 50: D D D C D C C C C C C C C C C 2 60: C C C C C C C C C C C C C C C C 70: C C C C C C C C C C C C C C C C 80: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 90: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 A0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Log file of training sequence: Power on the line is -13.356 dBm tone detected = 40 -->SNR (lin) = 467.829 Power on the line is -18.901 dBm tone detected = 56 -->SNR (lin) = 237.530 Power on the line is -18.195 dBm tone detected = 64 -->SNR (lin) = 182.346 AME: peerModemFound at time : 2145 --- Activator --- REPORT MODEMLINECONTROLLER notify : ITU_HS_FOUND PeerModemDetector::stopTranceiver _active_detectionMode == ADM_DETECT_ITU HS : TRELLIS_IN_LITE_IMPLEMENTED = #0x0# ==>>HsSegPool: getFreeSegment: returned [0] = ==>>HsSegPool: getFreeSegment: returned [1] = ** HS DL notify state *** enter : 0 ** HS DL notify state *** enter : 1 Start HandshakeSequence Installing initial TEQ coefficients new gain: 1800 /100 HandshakeSequence(commmon): new gain = 1855 /100 RxGain before C-TONE AnalogInterface : Message transfered after filtering 0x0x6200 AnalogInterface : Message transfered after filtering 0x0x5002 AnalogInterface : Message transfered after filtering 0x0x5002 doing power measurement on C-TONES Power on the line is -13.354 dBm tone detected = 40 -->SNR (lin) = 512.757 Power on the line is -18.903 dBm tone detected = 56 -->SNR (lin) = 260.488 Power on the line is -18.190 dBm tone detected = 64 -->SNR (lin) = 200.681 CTones end of detection : 1,40 doCtonesProcessing, measuredPower = 1048576.000 RMS line single = 98.418 handshakeSequence(nt): new gain = 2397 /100 handshakeSequence(nt): new gain = 3097 /100 RxGain after C-TONE AnalogInterface : Message transfered after filtering 0x0x6800 Handshake pilot tone: 40 gain scale factor 0.962 g1, g2 : 491,24857 DPLL (g1 = 491, g2= 24857) : freq error = 1.85189208984375e1 ppm, dpll_loop acc = 0x136E AnalogInterface : Message transfered after filtering 0x0x5342 Remaining frequency error 20.518 DPLL (g1 = 491, g2= 24857) : freq error = 4.840087890625e0 ppm, dpll_loop acc = 0x512 [before 4QAM - 2BAM] : Remaining frequency error 4.840 4QAM : x = 8227.000, y = 8156.000 DPLL (g1 = 491, g2= 24857) : freq error = 3.142333984375e0 ppm, dpll_loop acc = 0x34C Remaining frequency error = 3.142 Doing phase rotation installing demodulation ** HS DL notify state *** enter : 3 sending RTone1 pvoTimeRTone1: 2621 enable counter reload HS BIT-BYTE sync :: GALF detected. HS BIT-BYTE sync :: GALF detected. HS :: send flags. ** HS DL notify state *** enter : 4 ==>>HsSegPool: getFreeSegment: returned [2] = ###### HsProtTimer :: timer not running #####. ==>>HsSegPool: releaseSegment: found [2] = ###### HsProtTimer :: timer not running #####. ==>>HsSegPool: releaseSegment: found [0] = ==>>HsSegPool: getFreeSegment: returned [0] = ==>>HsSegPool: getFreeSegment: returned [2] = ==>>HsSegPool: getFreeSegment: returned [3] = ==>>HsSegPool: releaseSegment: found [0] = ==>>HsSegPool: releaseSegment: found [2] = ###### HsProtTimer :: timer not running #####. ==>>HsSegPool: releaseSegment: found [1] = ==>>HsSegPool: getFreeSegment: returned [0] = ==>>HsSegPool: getFreeSegment: returned [1] = ==>>HsSegPool: releaseSegment: found [0] = ###### HsProtTimer :: timer not running #####. ==>>HsSegPool: releaseSegment: found [3] = ==>>HsSegPool: getFreeSegment: returned [0] = ==>>HsSegPool: getFreeSegment: returned [2] = ==>>HsSegPool: getFreeSegment: returned [3] = ==>>HsSegPool: releaseSegment: found [0] = ==>>HsSegPool: releaseSegment: found [2] = ###### HsProtTimer :: timer not running #####. ==>>HsSegPool: releaseSegment: found [1] = ** HS DL notify state *** enter : 5 ==>>HsSegPool: getFreeSegment: returned [0] = disable Transmit Soc channel -> send quiet. disable Receive Soc channel. ==>>HsSegPool: releaseSegment: found [0] = ==>>HsSegPool: releaseSegment: found [2] = ==>>HsSegPool: releaseSegment: found [3] = ==>>HsSegPool: releaseSegment: found [0] = ** HS DL notify state *** enter : 6 *** start INITIALIZING *** +++ TRAINING +++ vendor code: 0x4753504E version code: 0x3 Installing initial TEQ coefficients AnalogInterface : Message transfered after filtering 0x0x5342 AnalogInterface : Message transfered after filtering 0x0x5342 RxGain MID before C-REVERB1 AGC phase : 1 , 'gain'=7.592 WARNING !!! getRxBPFGain function is used only for ADSF and ADSG..... AnalogInterface : Message transfered after filtering 0x0x2180 Putting analog gain to 7 dB Putting FFT scale to 5 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 dyn threshold: -33.354 Power on the line is -25.925 dBm Pilot detected -->SNR (lin) = 176506.096 C_PILOT detected TrainingSequence::adaptPilotFeq pilot = 64 x = 484.562 y = -1525.375 scale = 7.238 installing DPLL coefficients DPLL (g1 = 274, g2= 18575) : freq error = 2.52801513671875e0 ppm, dpll_loop acc = 0x2A7 AnalogInterface : Message transfered after filtering 0x0x5402 DPLL (g1 = 154, g2= 13931) : freq error = -2.29345703125e0 ppm, dpll_loop acc = 0xFD98 DPLL (g1 = 86, g2= 10448) : freq error = -2.34930419921875e0 ppm, dpll_loop acc = 0xFD89 ToneTriggerModule: enable recording of C_REVERB1 P_Rx = 3.435808658599853515e8 P_echo = 2.360100269317626953e4 P_tot = 3.436044216156005859e8 P_RxBoost = 1.384931449890136718e9 AnalogInterface : Message transfered after filtering 0x0x4100 Putting analog gain to 11 dB Putting FFT scale to 5 +++ ANALYSIS +++ Pilot rescale ... x = -7221.312 y = 7184.187 scale = 1.137 Echo Measurement ... DcOffset value : -2.24655032157897949e2 Channel Measurement ... DcOffset value : -2.25323724746704101e2 First TEQ-FEQ calculation !! FIRST_MEDLEY_TONE_INTEROP_MASKING 220 : DELTA_SNR_INTEROP_MASKING = 2 do NOT MASK tone 242 do NOT MASK tone 243 do NOT MASK tone 244 do NOT MASK tone 245 do NOT MASK tone 246 do NOT MASK tone 247 do NOT MASK tone 248 do NOT MASK tone 249 do NOT MASK tone 250 do NOT MASK tone 251 do NOT MASK tone 252 do NOT MASK tone 253 do NOT MASK tone 254 do NOT MASK tone 255 P_Rx = 1.105629086494445800e9 P_echo = 4.678012847900390625e2 P_tot = 1.105629444122314453e9 Calculated window move parameter : 332 *** Start EXCHANGE *** New PILOT has carrier number 60 RTV value for segue detection : 37 +++ start transmitSequence +++ enable synchronuous schedule swap Seque symbol detected at sync 89 and symb 7 C_MESSAGES1 received completely Psd down: -40 Target NM: 6 Downstream option #0 interl : 224 Downstream option #0 fast : 0 Downstream option #0 RS interl:16 Downstream option #0 2*S : 2 Downstream option #0 Idepth : 64 Downstream option #1 interl : 149 Downstream option #1 fast : 0 Downstream option #1 RS interl:16 Downstream option #1 2*S : 2 Downstream option #1 Idepth : 64 Downstream option #2 interl : 75 Downstream option #2 fast : 0 Downstream option #2 RS interl:8 Downstream option #2 2*S : 4 Downstream option #2 Idepth : 32 Downstream option #3 interl : 1 Downstream option #3 fast : 0 Downstream option #3 RS interl:1 Downstream option #3 2*S : 32 Downstream option #3 Idepth : 2 --------------------------------------------------------------- MODEM INITIALIZING IN OPERATION MODE G_LITE !!!!! INITIALIZATION SPECIFICATIONS : STANDARD COMPLIANT INITIATIZATION !!!!! INITIALIZATION SPECIFICATIONS : MINUMUM OVERHEAD FRAMING !!!!! --------------------------------------------------------------- AnalogInterface : Message transfered after filtering 0x0x7402 build R_MESSAGES1 New PILOT has carrier number 95 force counter reload TransmitSequence: Counter reload event Calculate final TEQ Calculate final window move TEQ-FEQ : DcOffset value : -1.02489018440246582e3 FSE after TEQ: 5 RTV value for segue detection : 109 SNR Measurement ... enable counter reload SNR measurement ... Calculating max capacity ... SNR medley: 38: 15 19 22 25 27 29 30 31 32 33 48: 34 35 37 38 39 39 40 41 42 42 58: 43 44 44 45 45 45 0 46 46 46 68: 47 47 47 47 47 47 47 47 47 47 78: 47 47 47 47 47 47 47 47 47 47 88: 47 47 47 47 47 47 46 47 47 47 98: 47 47 47 47 47 47 47 47 47 47 108: 47 47 47 47 47 47 47 47 47 47 118: 47 47 47 47 47 47 47 47 47 47 maxPower = 112.044 Max capacity Execution time = 14 ms Total_number_of_bits_supported = 876 Performance_Margin = 4.500 dB uncoded snr: 633 coded snr: 633 averageBi : 10 Coding Gain (in units of 0.5 dB : 4 Build R_MESSAGES_RA enable counter reload TransmitSequence: Counter reload event Seque symbol detected at sync 232 and symb 52 decode C_MESSAGES_RA Extract parameters from C_MESSAGES_RA option 0: 0 0 0 0 0 0 0 0 0 0 113 0 0 0 0 0 0 28 0 0 0 8 2 16 0 0 2 8 4 0 Downstream option #0 interl : 113 Downstream option #0 fast : 0 Downstream option #0 RS interl:8 Downstream option #0 2*S : 4 Downstream option #0 Idepth : 16 option 1: 0 0 0 0 0 0 0 0 0 0 109 0 0 0 0 0 0 27 0 0 0 8 2 16 0 0 2 8 4 0 Downstream option #1 interl : 109 Downstream option #1 fast : 0 Downstream option #1 RS interl:8 Downstream option #1 2*S : 4 Downstream option #1 Idepth : 16 option 2: 0 0 0 0 0 0 0 0 0 0 105 0 0 0 0 0 0 23 0 0 0 8 2 16 0 0 2 8 4 0 Downstream option #2 interl : 105 Downstream option #2 fast : 0 Downstream option #2 RS interl:8 Downstream option #2 2*S : 4 Downstream option #2 Idepth : 16 option 3: 0 0 0 0 0 0 0 0 0 0 91 0 0 0 0 0 0 19 0 0 0 16 1 64 0 0 2 8 4 0 Downstream option #3 interl : 91 Downstream option #3 fast : 0 Downstream option #3 RS interl:16 Downstream option #3 2*S : 2 Downstream option #3 Idepth : 64 requested noise margin = 6 requested max noise margin = 0 requested min noise margin = 0 Data rate option selection SNR medley: 38: 15 19 22 25 27 29 30 31 32 33 48: 34 35 37 38 39 39 40 41 42 42 58: 43 44 44 45 45 45 0 46 46 46 68: 47 47 47 47 47 47 47 47 47 47 78: 47 47 47 47 47 47 47 47 47 47 88: 47 47 47 47 47 47 46 47 47 47 98: 47 47 47 47 47 47 47 47 47 47 108: 47 47 47 47 47 47 47 47 47 47 118: 47 47 47 47 47 47 47 47 47 47 maxPower = 112.044 Max_number_of_bits_supported = 1028 Build R_MESSAGE2 enable counter reload Calculating final capacity ... results BIGI algorithm: tone bi gi mi 38 2 1 7 39 3 2 6 40 4 1 7 41 5 1 6 42 6 2 6 43 6 0 6 44 7 2 6 45 7 1 6 46 7 0 6 47 8 2 6 48 8 0 6 49 9 2 6 50 9 1 6 51 9 0 6 52 10 2 6 53 10 1 6 54 10 0 6 55 10 0 6 56 11 2 6 57 11 1 6 58 11 0 6 59 11 0 6 60 11 0 6 61 12 2 6 62 12 1 6 63 12 1 6 64 0 0 0 65 12 1 7 66 12 0 6 67 12 0 6 68 12 0 6 69 12 0 6 70 12 0 6 71 12 0 6 72 12 0 6 73 12 0 7 74 12 0 6 75 13 2 6 76 13 2 6 77 13 2 6 78 13 2 6 79 13 2 6 80 13 2 6 81 13 2 6 82 13 2 6 83 12 0 6 84 13 2 6 85 12 0 6 86 12 0 6 87 12 0 7 88 12 0 6 89 12 0 6 90 12 0 6 91 12 0 6 92 12 0 6 93 12 0 6 94 12 0 6 95 2 0 36 96 12 0 6 97 12 0 6 98 12 0 6 99 12 0 6 100 12 0 6 101 12 0 6 102 12 0 6 103 12 0 6 104 12 0 6 105 12 0 6 106 12 0 6 107 12 0 7 108 12 0 6 109 12 0 7 110 12 0 6 111 12 0 6 112 12 0 6 113 12 0 6 114 12 0 7 115 12 0 6 116 12 0 6 117 12 0 6 118 12 0 6 119 12 0 7 120 12 0 6 121 12 0 6 122 12 0 6 123 12 0 6 124 12 0 6 125 12 0 6 126 12 0 6 127 12 0 6 final capacity execution time = 24 ms ) Final_number_of_bits_supported = 976 Requested_number_of_bits = 976 Performance_Margin = 6.000 dB Selected Option = 0 TransmitSequence: Counter reload event Seque symbol detected at sync 6 and symb 100 C_MESSAGES2 received completely force counter reload Build R_BIGI Prepare Receive SHOWTIME force counter reload enable synchronuous schedule swap TransmitSequence: Counter reload event Prepare Transmit SHOWTIME Ftg value for sync : 21852 enable synchronuous schedule swap *** start RUNTIME *** Showtime SNR monitoring will be started setMaskMain on interruptDispatcher DPLL (g1 = 87, g2= 10466) : freq error = -2.25250244140625e0 ppm, dpll_loop acc = 0xFDA3 DC offset: -1.02413833141326904e3 MNM=86 ANM=102 Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out MNM=86 ANM=102 MNM=86 ANM=101 MNM=84 ANM=101 MNM=86 ANM=101 DPLL (g1 = 87, g2= 10466) : freq error = -2.29718017578125e0 ppm, dpll_loop acc = 0xFD97 DC offset: -1.02408909797668457e3 MNM=86 ANM=101 MNM=85 ANM=100 Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out MNM=87 ANM=101 Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out Aoc fifo A will be read out Aoc fifo B will be read out