Bootdata ok (command line is auto BOOT_IMAGE=slackpbx ro root=802) Linux version 2.6.16.2 (root@pbx) (gcc version 3.4.4) #2 Thu Apr 13 09:59:53 PDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable) BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data) BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS) BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000fa880 ACPI: RSDT (v001 A M I OEMRSDT 0x08000522 MSFT 0x00000097) @ 0x000000003ffb0000 ACPI: FADT (v001 A M I OEMFACP 0x08000522 MSFT 0x00000097) @ 0x000000003ffb0200 ACPI: MADT (v001 A M I OEMAPIC 0x08000522 MSFT 0x00000097) @ 0x000000003ffb0390 ACPI: OEMB (v001 A M I OEMBIOS 0x08000522 MSFT 0x00000097) @ 0x000000003ffc0040 ACPI: DSDT (v001 A0277 A0277001 0x00000001 MSFT 0x0100000d) @ 0x0000000000000000 On node 0 totalpages: 257355 DMA zone: 2913 pages, LIFO batch:0 DMA32 zone: 254442 pages, LIFO batch:31 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:15 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:bf780000) Checking aperture... CPU 0: aperture @ f4000000 size 64 MB Built 1 zonelists Kernel command line: auto BOOT_IMAGE=slackpbx ro root=802 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. time.c: Detected 1802.386 MHz processor. Console: colour VGA+ 80x50 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Memory: 1027432k/1048256k available (2255k kernel code, 20148k reserved, 1116k data, 184k init) Calibrating delay using timer specific routine.. 3613.16 BogoMIPS (lpj=7226333) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU: AMD Athlon(tm) 64 Processor 3000+ stepping 02 Using local APIC timer interrupts. result 12516579 Detected 12.516 MHz APIC timer. testing NMI watchdog ... OK. DMI 2.3 present. NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:00:0b.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 *11 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled. SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report agpgart: Detected AGP bridge 0 agpgart: AGP aperture is 64M @ 0xf4000000 PCI-DMA: Disabling IOMMU. PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:01.0 to 64 IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] Real Time Clock Driver v1.12ac Software Watchdog Timer: 0.07 initialized. soft_noboot=0 soft_margin=60 sec (nowayout= 0) Linux agpgart interface v0.101 (c) Dave Jones serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled isa bounce pool size: 16 pages floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 169 sk98lin: Asus mainboard with buggy VPD? Correcting data. eth0: Yukon Gigabit Ethernet 10/100/1000Base-T Adapter PrefPort:A RlmtMode:Check Link State tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky netconsole: not configured, aborting Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller at PCI slot 0000:00:0f.1 GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 177 PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 1 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1 ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio Probing IDE interface ide0... Probing IDE interface ide1... Probing IDE interface ide0... Probing IDE interface ide1... libata version 1.20 loaded. sata_via 0000:00:0f.0: version 1.1 ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 177 PCI: Via IRQ fixup for 0000:00:0f.0, from 11 to 1 sata_via 0000:00:0f.0: routed to hard irq line 1 ata1: SATA max UDMA/133 cmd 0xD400 ctl 0xD002 bmdma 0xC000 irq 177 ata2: SATA max UDMA/133 cmd 0xC800 ctl 0xC402 bmdma 0xC008 irq 177 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01 87:4023 88:407f ata1: dev 0 ATA-7, max UDMA/133, 586072368 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_via ata2: SATA link down (SStatus 0) scsi1 : sata_via Vendor: ATA Model: ST3300831AS Rev: 3.06 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 586072368 512-byte hdwr sectors (300069 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:00:10.4[C] -> GSI 21 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:10.4, from 10 to 9 ehci_hcd 0000:00:10.4: EHCI Host Controller ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:10.4: irq 185, io mem 0xfbf00000 ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:10.0[A] -> GSI 21 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:10.0, from 5 to 9 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 185, io base 0x0000d800 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.1[A] -> GSI 21 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:10.1, from 5 to 9 uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 185, io base 0x0000e000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.2[B] -> GSI 21 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:10.2, from 11 to 9 uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 185, io base 0x0000e400 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:10.3[B] -> GSI 21 (level, low) -> IRQ 185 PCI: Via IRQ fixup for 0000:00:10.3, from 11 to 9 uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: irq 185, io base 0x0000e800 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice Linux telephony interface: v1.00 oprofile: using NMI interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI wakeup devices: PCI0 PS2K AC97 USB1 USB2 USB3 USB4 EHCI PWRB SLPB ACPI: (supports S0 S1 S3 S4 S5) ReiserFS: sda2: found reiserfs format "3.6" with standard journal input: AT Translated Set 2 keyboard as /class/input/input0 ReiserFS: sda2: using ordered data mode ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda2: checking transaction log (sda2) ReiserFS: sda2: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 184k freed Adding 3863624k swap on /dev/sda3. Priority:-1 extents:1 across:3863624k Zapata Telephony Interface Registered on major 196 Zaptel Version: 1.2.5 Echo Canceller: KB1 ReiserFS: sda1: found reiserfs format "3.6" with standard journal ReiserFS: sda1: using ordered data mode ReiserFS: sda1: journal params: device sda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda1: checking transaction log (sda1) ReiserFS: sda1: Using r5 hash to sort names eth0: network connection up using port A speed: 100 autonegotiation: yes duplex mode: full flowctrl: symmetric irq moderation: disabled scatter-gather: disabled tx-checksum: disabled rx-checksum: disabled Registered tone zone 0 (United States / North America) Registered tone zone 0 (United States / North America) Registered tone zone 0 (United States / North America)