Linux version 2.6.21-ren (benq@stimpy) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #1 SMP Mon Apr 30 14:31:43 EST 2007 BIOS-provided physical RAM map: sanitize start sanitize end copy_e820_map() start: 0000000000000000 size: 000000000009f800 end: 000000000009f800 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000000009f800 size: 0000000000000800 end: 00000000000a0000 type: 2 copy_e820_map() start: 00000000000dc000 size: 0000000000024000 end: 0000000000100000 type: 2 copy_e820_map() start: 0000000000100000 size: 000000003fd90000 end: 000000003fe90000 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000003fe90000 size: 0000000000008000 end: 000000003fe98000 type: 3 copy_e820_map() start: 000000003fe98000 size: 0000000000068000 end: 000000003ff00000 type: 4 copy_e820_map() start: 000000003ff00000 size: 0000000000100000 end: 0000000040000000 type: 2 copy_e820_map() start: 00000000e0000000 size: 0000000010000000 end: 00000000f0000000 type: 2 copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2 copy_e820_map() start: 00000000fed14000 size: 0000000000006000 end: 00000000fed1a000 type: 2 copy_e820_map() start: 00000000fed1c000 size: 0000000000074000 end: 00000000fed90000 type: 2 copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 copy_e820_map() start: 00000000ff000000 size: 0000000001000000 end: 0000000100000000 type: 2 BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fe90000 (usable) BIOS-e820: 000000003fe90000 - 000000003fe98000 (ACPI data) BIOS-e820: 000000003fe98000 - 000000003ff00000 (ACPI NVS) BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved) 126MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f7700 Entering add_active_range(0, 0, 261776) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229376 HighMem 229376 -> 261776 early_node_map[1] active PFN ranges 0: 0 -> 261776 On node 0 totalpages: 261776 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1760 pages used for memmap Normal zone: 223520 pages, LIFO batch:31 HighMem zone: 253 pages used for memmap HighMem zone: 32147 pages, LIFO batch:7 DMI present. ACPI: RSDP 000F75D0, 0014 (r0 PTLTD ) ACPI: RSDT 3FE91A45, 003C (r1 GATEWA M 20060421 LTP 0) ACPI: FACP 3FE97E20, 0074 (r1 GATEWA M 20060421 LOHR 5A) ACPI: DSDT 3FE9240B, 5A15 (r1 GATEWA M 20060421 MSFT 100000E) ACPI: FACS 3FE98FC0, 0040 ACPI: APIC 3FE97E94, 0068 (r1 GATEWA M 20060421 LOHR 5A) ACPI: BOOT 3FE97FD8, 0028 (r1 GATEWA M 20060421 LTP 1) ACPI: MCFG 3FE97F34, 003C (r1 GATEWA M 20060421 LOHR 5A) ACPI: APIC 3FE97F70, 0068 (r1 GATEWA M 20060421 LTP 0) ACPI: SSDT 3FE91A81, 0500 (r1 PmRef CpuPm 3000 INTL 20050228) ACPI: BIOS bug: multiple APIC/MADT found, using 0 ACPI: If "acpi_apic_instance=2" works better, notify linux-acpi@vger.kernel.org ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:14 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 6:14 APIC version 20 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists. Total pages: 259731 Kernel command line: root=/dev/sda2 ro vga=792 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1663.199 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1033568k/1047104k available (2598k kernel code, 12972k reserved, 844k data, 216k init, 129600k highmem) virtual kernel memory layout: fixmap : 0xfff9d000 - 0xfffff000 ( 392 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf8000000 ( 896 MB) .init : 0xc0464000 - 0xc049a000 ( 216 kB) .data : 0xc0389879 - 0xc045ca94 ( 844 kB) .text : 0xc0100000 - 0xc0389879 (2598 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3328.65 BogoMIPS (lpj=1664327) Security Framework v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 14k freed ACPI: Core revision 20070126 CPU0: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3325.79 BogoMIPS (lpj=1662896) CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c1a9 00000000 00000000 monitor/mwait feature present. CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 CPU: After all inits, caps: bfe9fbff 00100000 00000000 00002940 0000c1a9 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: Intel Genuine Intel(R) CPU T2300 @ 1.66GHz stepping 08 Total of 2 processors activated (6654.44 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 checking TSC synchronization [CPU#0 -> CPU#1]: passed. Brought up 2 CPUs migration_cost=44 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1180-11bf claimed by ICH6 GPIO Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:1e.0 PCI: Bus #06 (-#07) is hidden behind transparent bridge #05 (-#05) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11 ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 8 devices SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report NET: Registered protocol family 8 NET: Registered protocol family 20 pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:01: iomem range 0xfed14000-0xfed17fff could not be reserved pnp: 00:01: iomem range 0xfed18000-0xfed18fff could not be reserved pnp: 00:01: iomem range 0xfed19000-0xfed19fff could not be reserved ieee1394: Initialized config rom entry `ip1394' PCI: Enabling device 0000:05:01.1 (0000 -> 0002) ACPI: PCI Interrupt 0000:05:01.1[B] -> GSI 19 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:05:01.1 to 64 Time: tsc clocksource has been installed. ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[de005000-de0057ff] Max Packet=[2048] IR/IT contexts=[4/8] PCI: Failed to allocate mem resource #6:20000@d0000000 for 0000:01:00.0 PCI: Bridge: 0000:00:01.0 IO window: disabled. MEM window: dc000000-ddffffff PREFETCH window: c0000000-cfffffff PCI: Bridge: 0000:00:1c.0 IO window: 2000-2fff MEM window: d8000000-d9ffffff PREFETCH window: d2000000-d3ffffff PCI: Bridge: 0000:00:1c.1 IO window: 3000-3fff MEM window: d6000000-d7ffffff PREFETCH window: d0000000-d1ffffff PCI: Bridge: 0000:00:1c.2 IO window: 4000-4fff MEM window: da000000-dbffffff PREFETCH window: d4000000-d5ffffff PCI: Bus 6, cardbus bridge: 0000:05:01.0 IO window: 00005000-000050ff IO window: 00005400-000054ff PREFETCH window: 50000000-53ffffff MEM window: 54000000-57ffffff PCI: Bridge: 0000:00:1e.0 IO window: 5000-5fff MEM window: de000000-de0fffff PREFETCH window: 50000000-53ffffff ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:01.0 to 64 ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1c.0 to 64 ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1c.1 to 64 ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1c.2 to 64 PCI: Enabling device 0000:00:1e.0 (0004 -> 0007) PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:05:01.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:05:01.0[A] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:05:01.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Simple Boot Flag at 0x36 set to 0x80 audit: initializing netlink socket (disabled) audit(1179674143.353:1): initialized highmem bounce pool size: 64 pages io scheduler noop registered io scheduler anticipatory registered (default) PCI: Setting latency timer of device 0000:00:01.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:01.0:pcie00] Allocate Port Service[0000:00:01.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] PCI: Setting latency timer of device 0000:00:1c.1 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.1:pcie00] Allocate Port Service[0000:00:1c.1:pcie02] Allocate Port Service[0000:00:1c.1:pcie03] PCI: Setting latency timer of device 0000:00:1c.2 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:1c.2:pcie00] Allocate Port Service[0000:00:1c.2:pcie02] Allocate Port Service[0000:00:1c.2:pcie03] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 pciehp: HPC vendor_id 8086 device_id 27d0 ss_vid 0 ss_did 0 Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 pciehp: Cannot get control of hotplug hardware for pci 0000:00:1c.0 pciehp: HPC vendor_id 8086 device_id 27d2 ss_vid 0 ss_did 0 Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 pciehp: Cannot get control of hotplug hardware for pci 0000:00:1c.1 pciehp: HPC vendor_id 8086 device_id 27d4 ss_vid 0 ss_did 0 Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 pciehp: Cannot get control of hotplug hardware for pci 0000:00:1c.2 pciehp: PCI Express Hot Plug Controller Driver version: 0.4 vesafb: framebuffer at 0xc0000000, mapped to 0xf8880000, using 6144k, total 131072k vesafb: mode is 1024x768x32, linelength=4096, pages=1 vesafb: protected mode interface info at c000:d5d0 vesafb: pmi: set display start = c00cd606, set palette = c00cd670 vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da vesafb: scrolling: redraw vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device Real Time Clock Driver v1.12ac iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) iTCO_wdt: Found a ICH7-M TCO device (Version=2, TCOBASE=0x1060) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) iTCO_vendor_support: vendor-support=0 Linux agpgart interface v0.102 (c) Dave Jones agpgart: Detected an Intel 945GM Chipset. agpgart: AGP aperture is 256M @ 0x0 [drm] Initialized drm 1.1.0 20060810 Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled loop: loaded (max 8 devices) ata_piix 0000:00:1f.2: version 2.10ac1 ata_piix 0000:00:1f.2: MAP [ P0 P2 IDE IDE ] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x000118b0 irq 14 ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x000118b8 irq 15 scsi0 : ata_piix ata1.00: ATA-7: HTS541080G9SA00, MB4OC61M, max UDMA/100 ata1.00: 156301488 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : ata_piix Switched to high resolution mode on CPU 1 Switched to high resolution mode on CPU 0 ata2.00: ATAPI, max UDMA/33 ata2.00: configured for UDMA/33 scsi 0:0:0:0: Direct-Access ATA HTS541080G9SA00 MB4O PQ: 0 ANSI: 5 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 < sda5 sda6 > ieee1394: Host added: ID:BUS[0-00:1023] GUID[00c09f0000945181] sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 1:0:0:0: CD-ROM PHILIPS DVD+-RW SDVD8441 PX43 PQ: 0 ANSI: 5 sr0: scsi3-mmc drive: 12x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 1:0:0:0: Attached scsi CD-ROM sr0 sr 1:0:0:0: Attached scsi generic sg1 type 5 video1394: Installed video1394 module ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 20, io mem 0xde304000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 20, io base 0x00001800 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 16, io base 0x00001820 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 19, io base 0x00001840 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 17, io base 0x00001860 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new interface driver libusual usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2Q] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input0 i2c /dev entries driver ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 16 EDAC MC: Ver: 2.0.1 Apr 30 2007 TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' Starting balanced_irq Using IPI Shortcut mode Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0 input: SynPS/2 Synaptics TouchPad as /class/input/input1 ReiserFS: sda2: found reiserfs format "3.6" with standard journal ReiserFS: sda2: using ordered data mode ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda2: checking transaction log (sda2) ReiserFS: sda2: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 216k freed input: PC Speaker as /class/input/input2 sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman sdhci: SDHCI controller found at 0000:05:01.3 [104c:803c] (rev 0) sdhci [sdhci_probe()]: found 1 slot(s) PCI: Enabling device 0000:05:01.3 (0000 -> 0002) ACPI: PCI Interrupt 0000:05:01.3[A] -> GSI 18 (level, low) -> IRQ 19 sdhci [sdhci_probe_slot()]: slot 0 at 0xde005800, irq 19 PCI: Setting latency timer of device 0000:05:01.3 to 64 sdhci: ============== REGISTER DUMP ============== sdhci: Sys addr: 0x00000000 | Version: 0x00008900 sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000 sdhci: Argument: 0x00000000 | Trn mode: 0x00000000 sdhci: Present: 0x000a0000 | Host ctl: 0x00000000 sdhci: Power: 0x00000000 | Blk gap: 0x00000000 sdhci: Wake-up: 0x00000000 | Clock: 0x00000000 sdhci: Timeout: 0x00000000 | Int stat: 0x00000000 sdhci: Int enab: 0x00ff00fb | Sig enab: 0x00ff00fb sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000 sdhci: Caps: 0x01e030b0 | Max curr: 0x00000034 sdhci: =========================================== mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0 mmc0: SDHCI at 0xde005800 irq 19 DMA mmc0: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 21 width 0 timing 0 ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 18 (level, low) -> IRQ 19 mmc0: clock 187500Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0 mmc0: clock 187500Hz busmode 1 powermode 2 cs 1 Vdd 21 width 0 timing 0 mmc0: starting CMD0 arg 00000000 flags 00000040 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (0) mmc0: req done (CMD0): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: clock 187500Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0 mmc0: starting CMD8 arg 000001aa flags 00000075 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (8) mmc0: req done (CMD8): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: starting CMD55 arg 00000000 flags 00000015 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37) mmc0: req done (CMD55): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: starting CMD55 arg 00000000 flags 00000015 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37) mmc0: req done (CMD55): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: starting CMD55 arg 00000000 flags 00000015 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37) mmc0: req done (CMD55): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: starting CMD55 arg 00000000 flags 00000015 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (37) mmc0: req done (CMD55): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: starting CMD1 arg 00000000 flags 00000061 sdhci [sdhci_tasklet_finish()]: Ending request, cmd (1) mmc0: req done (CMD1): 1/0/0: 00000000 00000000 00000000 00000000 mmc0: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0 PCI: Setting latency timer of device 0000:04:00.0 to 64 sky2 0000:04:00.0: v1.14 addr 0xda000000 irq 19 Yukon-EC Ultra (0xb4) rev 2 sky2 eth0: addr 00:16:36:3c:f0:d0 Yenta: CardBus bridge found at 0000:05:01.0 [152d:0753] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:05:01.0, mfunc 0x01001922, devctl 0x66 ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.0d ipw3945: Copyright(c) 2003-2006 Intel Corporation Yenta: ISA IRQ mask 0x0cf8, PCI irq 19 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#05) from #05 to #07 pcmcia: parent PCI bridge I/O window: 0x5000 - 0x5fff pcmcia: parent PCI bridge Memory window: 0xde000000 - 0xde0fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:02:00.0 to 64 ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection PCI: Enabling device 0000:05:01.2 (0000 -> 0002) ACPI: PCI Interrupt 0000:05:01.2[A] -> GSI 18 (level, low) -> IRQ 19 ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 21 PCI: Setting latency timer of device 0000:00:1b.0 to 64 PCI: Setting latency timer of device 0000:05:01.2 to 64 Adding 979924k swap on /dev/sda5. Priority:-1 extents:1 across:979924k fuse init (API version 7.8) ReiserFS: sda6: found reiserfs format "3.6" with standard journal ReiserFS: sda6: using ordered data mode ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda6: checking transaction log (sda6) ReiserFS: sda6: Using r5 hash to sort names ipw3945: Detected geography ABG (11 802.11bg channels, 13 802.11a channels) ACPI: Battery Slot [BAT1] (battery present) ACPI: AC Adapter [ACAD] (on-line) ACPI: SSDT 3FE921D6, 01A8 (r1 PmRef Cpu0Ist 3000 INTL 20050228) ACPI: SSDT 3FE91F81, 01D0 (r1 PmRef Cpu0Cst 3001 INTL 20050228) ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: SSDT 3FE9237E, 0089 (r1 PmRef Cpu1Ist 3000 INTL 20050228) ACPI: SSDT 3FE92151, 0085 (r1 PmRef Cpu1Cst 3000 INTL 20050228) ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU1] (supports 8 throttling states) Time: acpi_pm clocksource has been installed. input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input4 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input5 ACPI: Sleep Button (CM) [SLPB] input: Lid Switch as /class/input/input6 ACPI: Lid Switch [LID] ACPI: Thermal Zone [TZ00] (36 C) sky2 eth0: enabling interface sky2 eth0: ram buffer 0K NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready ADDRCONF(NETDEV_UP): wlan0: link is not ready Bluetooth: Core ver 2.11 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 Clocksource tsc unstable (delta = -115115351 ns) nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86 Kernel Module 1.0-9755 Mon Feb 26 23:21:15 PST 2007 ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready ieee80211_crypt: registered algorithm 'TKIP' wlan0: no IPv6 routers present TKIP: replay detected: STA=00:13:d3:72:7b:ee previous TSC 000000000000 received TSC 000000000000