scsi1 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 3.0 aic7901: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs scsi 1:0:0:0: Direct-Access SB-3160S LINUX.CC R001 PQ: 0 ANSI: 3 target1:0:0: asynchronous scsi1:A:0:0: Tagged Queuing enabled. Depth 32 target1:0:0: Beginning Domain Validation target1:0:0: wide asynchronous target1:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 62) target1:0:0: Ending Domain Validation hda: ATAPI 24X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Attempting manual resume kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. sd 0:0:0:0: Attached scsi generic sg0 type 0 scsi 0:0:8:0: Attached scsi generic sg1 type 3 scsi 0:1:0:0: Attached scsi generic sg2 type 0 scsi 0:1:1:0: Attached scsi generic sg3 type 0 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 input: PC Speaker as /class/input/input2 piix4_smbus 0000:00:02.0: Found 0000:00:02.0 device Adding 7815612k swap on /dev/sda2. Priority:-1 extents:1 across:7815612k EXT3 FS on sda1, internal journal loop: loaded (max 8 devices) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3 FS on sda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. PM: Writing back config space on device 0000:04:04.0 at offset b (was 166814e4, writing 3291014) PM: Writing back config space on device 0000:04:04.0 at offset 3 (was 804000, wr iting 804010) PM: Writing back config space on device 0000:04:04.0 at offset 2 (was 2000000, w riting 2000003) PM: Writing back config space on device 0000:04:04.0 at offset 1 (was 2b00000, w riting 2b00146) sdb : very big device. try to use READ CAPACITY(16). sdb : READ CAPACITY(16) failed. sdb : status=0, message=00, host=5, driver=00 sdb : use 0xffffffff as device size SCSI device sdb: 4294967296 512-byte hdwr sectors (2199023 MB) sdb: Write Protect is off sdb: Mode Sense: cb 00 00 08 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb : very big device. try to use READ CAPACITY(16). sdb : READ CAPACITY(16) failed. sdb : status=0, message=00, host=5, driver=00 sdb : use 0xffffffff as device size SCSI device sdb: 4294967296 512-byte hdwr sectors (2199023 MB) sdb: Write Protect is off sdb: Mode Sense: cb 00 00 08 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: unknown partition table sd 1:0:0:0: Attached scsi disk sdb sd 1:0:0:0: Attached scsi generic sg4 type 0 NET: Registered protocol family 10 lo: Disabled Privacy Extensions ADDRCONF(NETDEV_UP): eth0: link is not ready tg3: eth0: Link is up at 100 Mbps, full duplex. tg3: eth0: Flow control is off for TX and off for RX. ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready input: Power Button (FF) as /class/input/input3 ACPI: Power Button (FF) [PWRF]