dmesg Linux version 2.6.20-gentoo-r8 (root@helix) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 SMP PREEMPT Fri May 18 18:30:19 EST 2007 Command line: root=/dev/sda2 CONSOLE=/dev/tty1 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f400 (usable) BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fff0000 (usable) BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS) BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 262128) 1 entries of 256 used end_pfn_map = 1048576 DMI 2.3 present. ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7530 ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff3040 ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff30c0 ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x000000003fff9500 ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff9600 ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x000000003fff9440 ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000 Entering add_active_range(0, 0, 159) 0 entries of 256 used Entering add_active_range(0, 256, 262128) 1 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 DMA32 4096 -> 1048576 Normal 1048576 -> 1048576 early_node_map[2] active PFN ranges 0: 0 -> 159 0: 256 -> 262128 On node 0 totalpages: 262031 DMA zone: 56 pages used for memmap DMA zone: 1382 pages reserved DMA zone: 2561 pages, LIFO batch:0 DMA32 zone: 3527 pages used for memmap DMA32 zone: 254505 pages, LIFO batch:31 Normal zone: 0 pages used for memmap Nvidia board detected. Ignoring ACPI timer override. If you got timer trouble try acpi_use_timer_override ACPI: PM-Timer IO Port: 0x4008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 (Bootup-CPU) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: BIOS IRQ0 pin2 override ignored. ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) ACPI: IRQ9 used by override. ACPI: IRQ14 used by override. ACPI: IRQ15 used by override. Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Nosave address range: 000000000009f000 - 00000000000a0000 Nosave address range: 00000000000a0000 - 00000000000f0000 Nosave address range: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) PERCPU: Allocating 32512 bytes of per cpu data Built 1 zonelists. Total pages: 257066 Kernel command line: root=/dev/sda2 CONSOLE=/dev/tty1 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) Checking aperture... CPU 0: aperture @ 1a10000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Memory: 1026280k/1048512k available (3465k kernel code, 21536k reserved, 1362k data, 244k init) Calibrating delay using timer specific routine.. 4032.49 BogoMIPS (lpj=8064980) Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 Freeing SMP alternatives: 32k freed ACPI: Core revision 20060707 Using local APIC timer interrupts. result 12594032 Detected 12.594 MHz APIC timer. Booting processor 1/2 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4030.36 BogoMIPS (lpj=8060727) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Dual Core AMD Opteron(tm) Processor 170 stepping 02 CPU 1: Syncing TSC to CPU 0. CPU 1: synchronized TSC with CPU 0 (last diff -81 cycles, maxerr 626 cycles) Brought up 2 CPUs testing NMI watchdog ... OK. Disabling vsyscall due to use of PM timer time.c: Using 3.579545 MHz WALL PM GTOD PM timer. time.c: Detected 2015.042 MHz processor. migration_cost=946 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG at e0000000 PCI: No mmconfig possible on device 00:18 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Transparent bridge - 0000:00:09.0 Boot video device is 0000:01:00.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK3] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled. ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 15 devices SCSI subsystem initialized libata version 2.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:01: ioport range 0x4000-0x407f could not be reserved pnp: 00:01: ioport range 0x4080-0x40ff has been reserved pnp: 00:01: ioport range 0x4400-0x447f has been reserved pnp: 00:01: ioport range 0x4480-0x44ff could not be reserved pnp: 00:01: ioport range 0x4800-0x487f has been reserved pnp: 00:01: ioport range 0x4880-0x48ff has been reserved PCI: Bridge: 0000:00:09.0 IO window: a000-afff MEM window: d3000000-d30fffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0d.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:0e.0 IO window: 9000-9fff MEM window: d0000000-d2ffffff PREFETCH window: c0000000-cfffffff PCI: Setting latency timer of device 0000:00:09.0 to 64 PCI: Setting latency timer of device 0000:00:0b.0 to 64 PCI: Setting latency timer of device 0000:00:0c.0 to 64 PCI: Setting latency timer of device 0000:00:0d.0 to 64 PCI: Setting latency timer of device 0000:00:0e.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 6, 262144 bytes) TCP established hash table entries: 131072 (order: 9, 2097152 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) audit(1180233363.828:1): initialized Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.28 [Flags: R/O]. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: Linking AER extended capability on 0000:00:0b.0 PCI: Linking AER extended capability on 0000:00:0c.0 PCI: Linking AER extended capability on 0000:00:0d.0 PCI: Linking AER extended capability on 0000:00:0e.0 PCI: Setting latency timer of device 0000:00:0b.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0b.0:pcie00] Allocate Port Service[0000:00:0b.0:pcie03] PCI: Setting latency timer of device 0000:00:0c.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0c.0:pcie00] Allocate Port Service[0000:00:0c.0:pcie03] PCI: Setting latency timer of device 0000:00:0d.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0d.0:pcie00] Allocate Port Service[0000:00:0d.0:pcie03] PCI: Setting latency timer of device 0000:00:0e.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:0e.0:pcie00] Allocate Port Service[0000:00:0e.0:pcie03] lp: driver loaded but no devices found Real Time Clock Driver v1.12ac Linux agpgart interface v0.101 (c) Dave Jones input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] ACPI: Fan [FAN] (on) ACPI: Thermal Zone [THRM] (40 C) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A parport: PnPBIOS parport detected. parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP(,...)] lp0: using parport0 (interrupt-driven). Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 loop: loaded (max 8 devices) pcnet32.c:v1.33 27.Jun.2006 tsbogend@alpha.franken.de forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:0a.0 to 64 forcedeth: using HIGHDMA eth0: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0 PPP generic driver version 2.4.2 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0 NFORCE-CK804: chipset revision 242 NFORCE-CK804: not 100% native mode: will probe irqs later NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround. NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA Probing IDE interface ide0... hda: WDC WD1200BB-00CAA1, ATA DISK drive hdb: WDC WD800BB-00CAA1, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: TSSTcorpCD/DVDW SH-S162L, ATAPI CD/DVD-ROM drive hdd: ASUS DVD-E616A2, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=65535/16/63<6>hda: hw_config=603b , UDMA(100) hda: cache flushes not supported hda: hda1 hda2 < hda5 > hdb: max request size: 128KiB hdb: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63<6>hdb: hw_config=6b00 , UDMA(100) hdb: cache flushes not supported hdb: hdb1 hdb2 hdb3 hdc: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 48X DVD-ROM drive, 2048kB Cache<6>hdd: hw_config=0000 , UDMA(100) aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.2 loaded sata_nv 0000:00:07.0: version 3.2 ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22 sata_nv 0000:00:07.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:07.0 to 64 ata1: SATA max UDMA/133 cmd 0xFFFFC20000004480 ctl 0xFFFFC200000044A0 bmdma 0xD800 irq 22 ata2: SATA max UDMA/133 cmd 0xFFFFC20000004580 ctl 0xFFFFC200000045A0 bmdma 0xD808 irq 22 scsi0 : sata_nv ata1: SATA link down (SStatus 0 SControl 300) scsi1 : sata_nv ata2: SATA link down (SStatus 0 SControl 300) ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 21 sata_nv 0000:00:08.0: Using ADMA mode PCI: Setting latency timer of device 0000:00:08.0 to 64 ata3: SATA max UDMA/133 cmd 0xFFFFC20000006480 ctl 0xFFFFC200000064A0 bmdma 0xC400 irq 21 ata4: SATA max UDMA/133 cmd 0xFFFFC20000006580 ctl 0xFFFFC200000065A0 bmdma 0xC408 irq 21 scsi2 : sata_nv ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata3.00: ATA-6, max UDMA/133, 234441648 sectors: LBA48 NCQ (depth 31/32) ata3.00: ata3: dev 0 multi count 1 ata3.00: configured for UDMA/133 scsi3 : sata_nv ata4: SATA link down (SStatus 0 SControl 300) scsi 2:0:0:0: Direct-Access ATA ST3120827AS 3.42 PQ: 0 ANSI: 5 ata3: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61 SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > sd 2:0:0:0: Attached scsi disk sda sd 2:0:0:0: Attached scsi generic sg0 type 0 ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20 ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20 PCI: Setting latency timer of device 0000:00:02.1 to 64 ehci_hcd 0000:00:02.1: EHCI Host Controller ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:02.1: debug port 1 PCI: cache line size of 64 is not supported by device 0000:00:02.1 ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000 ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23 ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23 PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:02.0: irq 23, io mem 0xd3104000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 10 ports detected USB Universal Host Controller Interface driver v3.0 Initializing USB Mass Storage driver... usb 1-3: new high speed USB device using ehci_hcd and address 3 usb 1-3: configuration #1 chosen from 1 choice usb 2-1: new full speed USB device using ohci_hcd and address 2 usb 2-1: configuration #1 chosen from 1 choice hub 2-1:1.0: USB hub found hub 2-1:1.0: 4 ports detected usb 2-4: new low speed USB device using ohci_hcd and address 3 usb 2-4: configuration #1 chosen from 1 choice scsi4 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. input: Logitech USB-PS/2 Optical Mouse as /class/input/input2 input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:02.0-4 usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input3 I2O subsystem v1.325 i2o: max drivers = 8 i2c /dev entries driver i2c_adapter i2c-0: nForce2 SMBus adapter at 0x4c00 i2c_adapter i2c-1: nForce2 SMBus adapter at 0x4c40 it87: Found IT8712F chip at 0x290, revision 7 it87: in3 is VCC (+5V) it87: in7 is VCCH (+5V Stand-By) it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface oprofile: using NMI interrupt. ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 drivers/rtc/hctosys.c: unable to open rtc device (rtc0) ReiserFS: sda2: found reiserfs format "3.6" with standard journal ReiserFS: sda2: using ordered data mode ReiserFS: sda2: journal params: device sda2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda2: checking transaction log (sda2) ReiserFS: sda2: Using r5 hash to sort names VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 244k freed ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17 ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17 Installing spdif_bug patch: Audigy 2 ZS [SB0350] nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:01:00.0 to 64 NVRM: loading NVIDIA UNIX x86_64 Kernel Module 1.0-9755 Mon Feb 26 23:16:31 PST 2007 ReiserFS: sda5: found reiserfs format "3.6" with standard journal ReiserFS: sda5: using ordered data mode ReiserFS: sda5: journal params: device sda5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda5: checking transaction log (sda5) ReiserFS: sda5: Using r5 hash to sort names ReiserFS: sda6: found reiserfs format "3.6" with standard journal ReiserFS: sda6: using ordered data mode ReiserFS: sda6: journal params: device sda6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda6: checking transaction log (sda6) ReiserFS: sda6: Using r5 hash to sort names ReiserFS: sda7: found reiserfs format "3.6" with standard journal ReiserFS: sda7: using ordered data mode ReiserFS: sda7: journal params: device sda7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: sda7: checking transaction log (sda7) ReiserFS: sda7: Using r5 hash to sort names ReiserFS: hdb2: found reiserfs format "3.6" with standard journal ReiserFS: hdb2: using ordered data mode ReiserFS: hdb2: journal params: device hdb2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 ReiserFS: hdb2: checking transaction log (hdb2) ReiserFS: hdb2: Using r5 hash to sort names NTFS volume version 3.0. NTFS volume version 3.0. Adding 1052216k swap on /dev/sda1. Priority:1 extents:1 across:1052216k scsi 4:0:0:0: Direct-Access Generic STORAGE DEVICE 9312 PQ: 0 ANSI: 0 sd 4:0:0:0: Attached scsi removable disk sdb sd 4:0:0:0: Attached scsi generic sg1 type 0 usb-storage: device scan complete hdd: irq timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: drive not ready for command hdd: status timeout: status=0xd0 { Busy } ide: failed opcode was: unknown hdd: DMA disabled hdd: drive not ready for command hdd: ATAPI reset complete hdd: command error: status=0x51 { DriveReady SeekComplete Error } hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 } ide: failed opcode was: unknown ATAPI device hdd: Error: Illegal request -- (Sense key=0x05) Logical block address out of range -- (asc=0x21, ascq=0x00) The failed "Seek" packet command was: "2b 00 00 07 82 30 00 00 00 00 00 00 00 00 00 00 " end_request: I/O error, dev hdd, sector 492080 Buffer I/O error on device hdd, logical block 61510 hdd: command error: status=0x51 { DriveReady SeekComplete Error } hdd: command error: error=0x54 { AbortedCommand LastFailedSense=0x05 } ide: failed opcode was: unknown ATAPI device hdd: Error: Illegal request -- (Sense key=0x05) Logical block address out of range -- (asc=0x21, ascq=0x00) The failed "Read 10" packet command was: "28 00 00 07 82 30 00 00 08 00 00 00 00 00 00 00 " end_request: I/O error, dev hdd, sector 492080 Buffer I/O error on device hdd, logical block 61510 lspci: 00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3) 00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3) 00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2) 00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) 00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) 00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2) 00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) 00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) 00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) 00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) 00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3) 00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) 00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) 00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) 00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:00.0 VGA compatible controller: nVidia Corporation Unknown device 0295 (rev a1) 05:07.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04) 05:07.1 Input device controller: Creative Labs SB Audigy Game Port (rev 04) 05:07.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04)