<4>[ 983.110000] Stopping tasks ... <7>n_tihtc_poll called <4>[ 983.140000] done. <4>[ 983.140000] Suspending console(s) <7>[ 983.140000] uda1380: uda hw write 2 val 0 <4>[ 983.140000] acx: suspend handler is experimental! <4>[ 983.140000] sus: dev c4840000 <4>[ 983.140000] sus: adev c4840340 <4>[ 983.140000] acx_set_status(0):STOPPED <4>[ 983.250000] blueangel_wlan_stop <4>[ 983.250000] asic3_gpio_set_value(23, 0) <4>[ 983.250000] asic3_gpio_set_value(25, 0) <4>[ 983.250000] asic3_gpio_set_value(45, 0) <4>[ 983.250000] blueangel_ds1wm: OWM_EN High (inactive) <4>[ 983.330000] blueangel_lcd_hw_off <4>[ 983.330000] brightness=0 for the led=6 <4>[ 983.330000] brightness=0 for the led=7 <7>[ 983.360000] DPM: pda_udc: Turning off port <4>[ 983.360000] asic3_gpio_set_value(42, 1) <4>[ 983.360000] Closing blueangel tsc2200 ssp... done! <4>[ 983.360000] ll_pm_suspend resume_addr=0xa02fa9a0 PSPR=0xc0000000 <4>[ 983.360000] Initializing blueangel tsc2200 ssp... done <7>[ 983.360000] DPM: pda_udc: Turning on port <4>[ 983.360000] asic3_gpio_set_value(42, 0) <6>[ 983.360000] asic3_mmc: starting resume <4>[ 983.360000] pxa_gpiodev_get_value(8) <4>[ 983.540000] pxa_gpiodev_get_value(8) <4>[ 983.600000] pxa_gpiodev_get_value(8) <4>[ 983.720000] pxa_gpiodev_get_value(8) <6>[ 984.030000] usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet Subset <6>[ 984.030000] usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet Subset <6>[ 984.680000] asic3_mmc: finished resume <4>[ 984.680000] blueangel_lcd_hw_init_preblueangel_lcd_hw_init_postbrightness=0 for the led=6 <4>[ 984.770000] brightness=0 for the led=7 <4>[ 984.830000] blueangel_lcd_hw_init_preblueangel_lcd_hw_init_postblueangel_ds1wm: OWM_EN Low (active) <4>[ 984.950000] asic3_gpio_set_value(23, 0) <4>[ 984.950000] asic3_gpio_set_value(25, 0) <4>[ 984.950000] asic3_gpio_set_value(45, 0) <4>[ 985.000000] acx: resume handler is experimental! <4>[ 985.000000] rsm: got dev c4840000 <4>[ 985.000000] rsm: got adev c4840340 <4>[ 985.000000] htcblueangel_wlan_start <4>[ 990.160000] i2c: error: timeout <4>[ 990.160000] i2c: msg_num: 0 msg_idx: 1 msg_ptr: 0 <4>[ 990.160000] i2c: ICR: 000017e0 ISR: 00000000 <4>[ 990.160000] i2c: log: [00000044:000017e8] [00000044:000017ea] [00000044:000017e0] <4>[ 990.160000] ACX radio type 0x0d <4>[ 990.160000] requesting firmware image 'WLANGEN.BIN' <7>[ 990.170000] uda1380: uda hw write 2 val 100 <5>[ 990.170000] ds2760-battery ds2760-battery.0: not enough power to charge <7>[ 990.170000] uda1380: uda hw write 2 val 100 <4>[ 990.170000] Restarting tasks ... first data mismatch at 0x00000000 good 0xea0021f8 bad 0x01030103 id 0x05050d03 <4>[ 990.460000] acx_write_fw (main):0 <4>[ 990.460000] acx: FATAL: firmware upload: data parts at offset 4 don't match <4>[ 990.460000] (0xEA0021F8 vs. 0x99999999)! <4>[ 990.460000] I/O timing issues or defective memory, with DWL-xx0+? ACX_IO_WIDTH=16 may help. Please report <4>[ 990.460000] acx_validate_fw (main):1 <4>[ 990.460000] acx: firmware upload attempt #1 FAILED, retrying... <4>[ 990.590000] done. <7>[ 990.620000] n_tihtc_poll called <4>[ 991.470000] first data mismatch at 0x00000000 good 0xea0021f8 bad 0x01030103 id 0x05059999 <4>[ 991.710000] acx_write_fw (main):0 <4>[ 991.710000] acx: FATAL: firmware upload: data parts at offset 4 don't match <4>[ 991.710000] (0xEA0021F8 vs. 0x99999999)! <4>[ 991.710000] I/O timing issues or defective memory, with DWL-xx0+? ACX_IO_WIDTH=16 may help. Please report <4>[ 991.710000] acx_validate_fw (main):1 <4>[ 991.710000] acx: firmware upload attempt #2 FAILED, retrying... <4>[ 992.720000] first data mismatch at 0x00000000 good 0xea0021f8 bad 0x01030103 id 0x05059999 <4>[ 992.960000] acx_write_fw (main):0 <4>[ 992.960000] acx: FATAL: firmware upload: data parts at offset 4 don't match <4>[ 992.960000] (0xEA0021F8 vs. 0x99999999)! <4>[ 992.960000] I/O timing issues or defective memory, with DWL-xx0+? ACX_IO_WIDTH=16 may help. Please report <4>[ 992.960000] acx_validate_fw (main):1 <4>[ 992.960000] acx: firmware upload attempt #3 FAILED, retrying...