<4>[ 377.370000] acx: this driver is still EXPERIMENTAL <4>[ 377.370000] acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion <4>[ 377.370000] acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them <4>[ 377.370000] running on a little-endian CPU <4>[ 377.370000] PCI module v0.3.36 initialized, waiting for cards to probe... <4>[ 377.380000] htcblueangel_wlan_start <4>[ 377.710000] acx: found ACX100-based wireless network card <4>[ 377.710000] initial debug setting is 0x000A <4>[ 377.720000] using IRQ 40 <4>[ 377.740000] ACX radio type 0x0d <4>[ 377.740000] requesting firmware image 'WLANGEN.BIN' <4>[ 378.160000] acx_write_fw (main): 0 <4>[ 378.300000] acx_validate_fw (main): 0 <4>[ 378.570000] requesting firmware image 'RADIO0d.BIN' <4>[ 378.650000] acx_write_fw (radio): 0 <4>[ 378.660000] acx_validate_fw (radio): 0 <4>[ 378.900000] acx100_s_init_wep: writing WEP options <4>[ 378.960000] initializing max packet templates <4>[ 379.260000] NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536 <4>[ 379.260000] CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01 <4>[ 379.260000] AntennaID:01 Len:02 Data:1E 00 <4>[ 379.260000] PowerLevelID:0A Len:00 Data: <4>[ 379.260000] DataRatesID:02 Len:05 Data:02 04 11 22 44 <4>[ 379.270000] DomainID:03 Len:07 Data:30 20 30 31 32 40 41 <4>[ 379.270000] ProductID:04 Len:09 Data:TI ACX100 <4>[ 379.270000] ManufacturerID:05 Len:07 Data:TI Tes~ <4>[ 379.300000] acx: === chipset TNETW1100B, radio type 0x0D (Maxim), form factor 0x03 (Compact Flash), EEPROM version 0x05: uploaded firmware 'Rev 1.10.7.K' === <4>[ 379.300000] get_mask 0x00004D82, set_mask 0x00000000 <4>[ 379.320000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 379.320000] got sensitivity value 176 <4>[ 379.340000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 379.340000] got antenna value 0x8D <4>[ 379.360000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 379.360000] got Energy Detect (ED) threshold 112 <4>[ 379.380000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 379.380000] got Channel Clear Assessment (CCA) value 13 <4>[ 379.400000] got regulatory domain 0x30 <4>[ 379.400000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 379.400000] new ratevector: 82 84 0B 16 2C <4>[ 379.400000] setting RXconfig to 2010:0FDD <4>[ 379.430000] creating /proc entry driver/acx_wlan0 <4>[ 379.430000] creating /proc entry driver/acx_wlan0_diag <4>[ 379.430000] creating /proc entry driver/acx_wlan0_eeprom <4>[ 379.430000] creating /proc entry driver/acx_wlan0_phy <4>[ 379.430000] acx v0.3.36: net device wlan0, driver compiled against wireless extensions 22 and Linux 2.6.21-hh5 <4>[ 380.140000] new adev->mode=2 <4>[ 380.270000] new adev->mode=2 <4>[ 380.820000] acx_set_status(1):SCANNING <4>[ 380.820000] updating initial settings on iface activation <4>[ 380.830000] get_mask 0x00000000, set_mask 0x0037EEFE <4>[ 380.830000] important setting has been changed. Need to update packet templates, too <4>[ 380.850000] updating packet templates <4>[ 380.870000] updating Tx fallback to 1 retries <4>[ 380.890000] updating transmit power: 6 dBm <4>[ 380.890000] wlan0: changing radio power level to 6 dBm (60) <4>[ 380.890000] updating antenna value: 0x8D <4>[ 380.910000] updating Energy Detect (ED) threshold: 112 <4>[ 380.930000] updating Channel Clear Assessment (CCA) value: 0x0D <4>[ 380.950000] updating channel to: 6 <4>[ 380.950000] updating: enable Tx <4>[ 380.970000] updating: enable Rx on channel: 6 <4>[ 380.990000] updating short retry limit: 7, long retry limit: 4 <4>[ 381.020000] sta_list_add: sta=EE:65:8E:A1:F9:60 <4>[ 381.020000] sta_list_add: sta=EE:65:8E:A1:F9:61 <4>[ 381.020000] sta_list_add: sta=EE:65:8E:A1:F9:62 <4>[ 381.020000] sta_list_add: sta=EE:65:8E:A1:F9:63 <4>[ 381.030000] updating tx MSDU lifetime: 4096 <4>[ 381.050000] updating regulatory domain: 0x30 <4>[ 381.070000] setting RXconfig to 2010:0FDD <4>[ 381.090000] updating WEP key settings <4>[ 381.090000] setting WEP key: 0 with total size: 5 <4>[ 381.110000] setting WEP key 0 as default <4>[ 381.130000] acx_set_status(1):SCANNING <4>[ 381.130000] sta_list_add: sta=EE:65:8E:A1:F9:63 <4>[ 381.130000] starting radio scan <4>[ 381.150000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 381.150000] get_mask 0x00000000, set_mask 0x00000040 <4>[ 381.150000] setting RXconfig to 2010:0FDD <4>[ 381.160000] sta_list_add: sta=EA:D9:7F:DD:B9:C8 <4>[ 381.160000] sta_list_add: sta=EA:D9:7F:DD:B9:C9 <4>[ 381.160000] sta_list_add: sta=EA:D9:7F:DD:B9:CA <4>[ 381.170000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 381.190000] sta_list_add: sta=00:14:A4:3B:5A:43 <4>[ 381.200000] get_mask 0x00000000, set_mask 0x00000040 <4>[ 381.200000] setting RXconfig to 2010:0FDD <4>[ 381.220000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 381.270000] sta_list_add: sta=EA:D9:7F:DD:B9:CB <4>[ 381.850000] acx: unknown EID 42 in mgmt frame at offset 58. IE: 2A 01 04 <4>[ 381.850000] sta_list_add: sta=EE:65:8E:A1:F9:60 <4>[ 381.850000] acx: unknown EID 42 in mgmt frame at offset 58. IE: 2A 01 04 <4>[ 381.860000] acx: unknown EID 42 in mgmt frame at offset 58. IE: 2A 01 04 <4>[ 381.940000] sta_list_add: sta=EE:65:8E:A1:F9:61 <4>[ 381.940000] sta_list_add: sta=EE:65:8E:A1:F9:62 <4>[ 382.130000] acx_i_timer: adev->status=1 (SCANNING) <4>[ 382.130000] continuing scan (1 sec) <4>[ 382.980000] scan table: SSID="freephonie" CH=6 SIR=48 SNR=0 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] ESSID doesn't match! ('freephonie' station, 'ReseauLinux' config) <4>[ 382.980000] scan table: SSID="freebox" CH=1 SIR=34 SNR=0 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] ESSID doesn't match! ('freebox' station, 'ReseauLinux' config) <4>[ 382.980000] scan table: SSID="" CH=1 SIR=32 SNR=31 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] found station with empty or single-space (hidden) SSID, considering for assoc attempt <4>[ 382.980000] scan table: SSID="" CH=1 SIR=30 SNR=33 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] found station with empty or single-space (hidden) SSID, considering for assoc attempt <4>[ 382.980000] scan table: SSID="WANADOO-E2D0" CH=1 SIR=56 SNR=33 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] ESSID doesn't match! ('WANADOO-E2D0' station, 'ReseauLinux' config) <4>[ 382.980000] scan table: SSID="freephonie" CH=1 SIR=29 SNR=33 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] ESSID doesn't match! ('freephonie' station, 'ReseauLinux' config) <4>[ 382.980000] scan table: SSID="ReseauLinux" CH=6 SIR=53 SNR=0 <4>[ 382.980000] peer_cap 0x0411, needed_cap 0x0001 <4>[ 382.980000] found station with matching ESSID! ('ReseauLinux' station, 'ReseauLinux' config) <4>[ 382.980000] matching station found: EE:65:8E:A1:F9:60, joining <4>[ 382.980000] sending authentication1 request (auth algo 0), awaiting response <4>[ 382.980000] acx_set_status(2):WAIT_AUTH <4>[ 382.980000] rates_basic:0003->03, rates_supported:0127->1F <4>[ 382.990000] AUTHEN adev->addr=00:09:2D:10:59:C7 a1=00:09:2D:10:59:C7 a2=EE:65:8E:A1:F9:60 a3=EE:65:8E:A1:F9:60 adev->bssid=EE:65:8E:A1:F9:60 <4>[ 382.990000] auth algorithm 0, auth sequence 2, status 0 <4>[ 382.990000] acx_set_status(3):AUTHENTICATED <4>[ 382.990000] sending association request, awaiting response. NOT ASSOCIATED YET <4>[ 382.990000] association: requesting caps 0x0011, ESSID "ReseauLinux" <4>[ 383.000000] BSS_Type = 2 <4>[ 383.000000] JoinBSSID MAC:EE:65:8E:A1:F9:60 <4>[ 383.020000] acx_set_status(4):ASSOCIATED <4>[ 383.020000] ASSOCIATED! <4>[ 384.490000] acx_i_timer: adev->status=4 (ASSOCIATED) <4>[ 384.800000] get_mask 0x00000000, set_mask 0x00000040 <4>[ 384.800000] setting RXconfig to 2010:0FDD <4>[ 384.820000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 384.910000] get_mask 0x00000000, set_mask 0x00000040 <4>[ 384.910000] setting RXconfig to 2010:0FDD <4>[ 384.930000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 408.970000] blueangel_lcd_hw_init_preblueangel_lcd_hw_init_postStopping tasks ... <7>n_tihtc_poll called <4>[ 409.080000] done. <4>[ 409.080000] Suspending console(s) <7>[ 409.080000] uda1380: uda hw write 2 val 0 <4>[ 409.080000] acx: suspend handler is experimental! <4>[ 409.080000] sus: dev c4f2c000 <4>[ 409.080000] sus: adev c4f2c340 <4>[ 409.080000] acx_set_status(0):STOPPED <4>[ 409.190000] blueangel_wlan_stop <4>[ 409.190000] asic3_gpio_set_value(23, 0) <4>[ 409.190000] asic3_gpio_set_value(25, 0) <4>[ 409.190000] asic3_gpio_set_value(45, 0) <4>[ 409.190000] blueangel_ds1wm: OWM_EN High (inactive) <4>[ 409.410000] blueangel_lcd_hw_off <4>[ 409.420000] brightness=0 for the led=6 <4>[ 409.420000] brightness=0 for the led=7 <7>[ 409.440000] DPM: pda_udc: Turning off port <4>[ 409.440000] asic3_gpio_set_value(42, 1) <4>[ 409.440000] Closing blueangel tsc2200 ssp... done! <4>[ 409.440000] ll_pm_suspend resume_addr=0xa02fa9a0 PSPR=0xc0000000 <4>[ 409.440000] Initializing blueangel tsc2200 ssp... done <7>[ 409.440000] DPM: pda_udc: Turning on port <4>[ 409.440000] asic3_gpio_set_value(42, 0) <6>[ 409.440000] asic3_mmc: starting resume <4>[ 409.440000] pxa_gpiodev_get_value(8) <4>[ 409.690000] pxa_gpiodev_get_value(8) <4>[ 409.750000] pxa_gpiodev_get_value(8) <4>[ 409.880000] pxa_gpiodev_get_value(8) <6>[ 410.180000] usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet Subset <6>[ 410.190000] usb0: full speed config #1: 100 mA, Ethernet Gadget, using CDC Ethernet Subset <6>[ 410.760000] asic3_mmc: finished resume <4>[ 410.760000] blueangel_lcd_hw_init_preblueangel_lcd_hw_init_postbrightness=0 for the led=6 <4>[ 410.850000] brightness=0 for the led=7 <4>[ 410.920000] blueangel_lcd_hw_init_preblueangel_lcd_hw_init_postblueangel_ds1wm: OWM_EN Low (active) <4>[ 411.040000] asic3_gpio_set_value(23, 0) <4>[ 411.040000] asic3_gpio_set_value(25, 0) <4>[ 411.040000] asic3_gpio_set_value(45, 0) <4>[ 411.090000] acx: resume handler is experimental! <4>[ 411.090000] rsm: got dev c4f2c000 <4>[ 411.090000] rsm: got adev c4f2c340 <4>[ 411.090000] htcblueangel_wlan_start <4>[ 416.400000] i2c: error: timeout <4>[ 416.400000] i2c: msg_num: 0 msg_idx: 1 msg_ptr: 0 <4>[ 416.400000] i2c: ICR: 000017e0 ISR: 00000000 <4>[ 416.400000] i2c: log: [00000044:000017e8] [00000044:000017ea] [00000044:000017e0] <4>[ 416.400000] ACX radio type 0x0d <4>[ 416.400000] requesting firmware image 'WLANGEN.BIN' <7>[ 416.410000] uda1380: uda hw write 2 val 100 <5>[ 416.410000] ds2760-battery ds2760-battery.0: not enough power to charge <7>[ 416.410000] uda1380: uda hw write 2 val 100 <4>[ 416.410000] Restarting tasks ... done. <7>[ 416.640000] n_tihtc_poll called <4>[ 416.710000] first data mismatch at 0x00000000 good 0xea0021f8 bad 0x01030103 id 0x05050d03 <4>[ 416.960000] acx_write_fw (main): 0 <4>[ 416.960000] acx: FATAL: firmware upload: data parts at offset 4 don't match <4>[ 416.960000] (0xEA0021F8 vs. 0x99999999)! <4>[ 416.960000] I/O timing issues or defective memory, with DWL-xx0+? ACX_IO_WIDTH=16 may help. Please report <4>[ 416.960000] acx_validate_fw (main): 1 <4>[ 416.960000] acx: firmware upload attempt #1 FAILED, retrying... <4>[ 417.970000] first data mismatch at 0x00000000 good 0xea0021f8 bad 0x01030103 id 0x05059999 <4>[ 418.210000] acx_write_fw (main): 0 <4>[ 418.210000] acx: FATAL: firmware upload: data parts at offset 4 don't match <4>[ 418.210000] (0xEA0021F8 vs. 0x99999999)! <4>[ 418.210000] I/O timing issues or defective memory, with DWL-xx0+? ACX_IO_WIDTH=16 may help. Please report <4>[ 418.210000] acx_validate_fw (main): 1 <4>[ 418.210000] acx: firmware upload attempt #2 FAILED, retrying... <4>[ 419.220000] first data mismatch at 0x00000000 good 0xea0021f8 bad 0x01030103 id 0x05059999 <4>[ 419.460000] acx_write_fw (main): 0 <4>[ 419.460000] acx: FATAL: firmware upload: data parts at offset 4 don't match <4>[ 419.460000] (0xEA0021F8 vs. 0x99999999)! <4>[ 419.460000] I/O timing issues or defective memory, with DWL-xx0+? ACX_IO_WIDTH=16 may help. Please report <4>[ 419.460000] acx_validate_fw (main): 1 <4>[ 419.460000] acx: firmware upload attempt #3 FAILED, retrying...