localhost ~ # dmesg Linux version 2.6.16-gentoo-r3 (root@localhost) (gcc version 3.4.5 (Gentoo 3.4.5-r1, ssp-3.4.5-1.0, pie-8.7.9)) #12 SMP PREEMPT Sun May 7 00:29:58 EDT 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 0000000000100000 - 000000003f7d3800 (usable) BIOS-e820: 000000003f7d3800 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0007000 (reserved) BIOS-e820: 00000000f0008000 - 00000000f000c000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fed20000 - 00000000fee10000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) Warning only 896MB will be used. Use a HIGHMEM enabled kernel. 896MB LOWMEM available. On node 0 totalpages: 229376 DMA zone: 4096 pages, LIFO batch:0 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 0 pages, LIFO batch:0 DMI 2.3 present. ACPI: RSDP (v000 DELL ) @ 0x000fc9b0 ACPI: RSDT (v001 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d3fd3 ACPI: FADT (v001 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d4c00 ACPI: MADT (v001 DELL CPi R 0x27d5091c ASL 0x00000047) @ 0x3f7d5400 ACPI: MCFG (v016 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d53c0 ACPI: BOOT (v001 DELL CPi R 0x27d5091c ASL 0x00000061) @ 0x3f7d4fc0 ACPI: SSDT (v001 PmRef Cpu0Ist 0x00003000 INTL 0x20030522) @ 0x3f7d43e6 ACPI: SSDT (v001 PmRef Cpu0Cst 0x00003001 INTL 0x20030522) @ 0x3f7d420e ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030522) @ 0x3f7d4013 ACPI: DSDT (v001 INT430 SYSFexxx 0x00001001 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:13 APIC version 20 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists Kernel command line: root=/dev/sda3 video=vesafb:1280x800@60,ywrap,mtrr vga=0x31A splash=verbose,fadein,theme:emergence CONSOLE=/dev/tty1 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 65536 bytes) Detected 1596.247 MHz processor. Using pmtmr for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 904080k/917504k available (2970k kernel code, 12840k reserved, 848k data, 248k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3200.34 BogoMIPS (lpj=6400690) Mount-cache hash table entries: 512 CPU: After generic identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 CPU: After vendor identify, caps: afe9fbff 00100000 00000000 00000000 00000180 00000000 00000000 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 2048K CPU: After all inits, caps: afe9fbff 00100000 00000000 00000040 00000180 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. CPU0: Intel(R) Pentium(R) M processor 1.60GHz stepping 08 Total of 1 processors activated (3200.34 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 Brought up 1 CPUs migration_cost=0 checking if image is initramfs... it is Freeing initrd memory: 217k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xfbaae, last bus=10 PCI: Using MMCONFIG ACPI: Subsystem revision 20060127 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 Boot video device is 0000:00:02.0 PCI quirk: region 1000-107f claimed by ICH6 ACPI/GPIO/TCO PCI quirk: region 1080-10bf claimed by ICH6 GPIO PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 PCI: Transparent bridge - 0000:00:1e.0 PCI: Bus #04 (-#07) may be hidden behind transparent bridge #03 (-#04) (try 'pci=assign-busses') ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *10 ACPI: PCI Interrupt Link [LNKC] (IRQs *9 10 11) ACPI: PCI Interrupt Link [LNKD] (IRQs 5 *7 9 10 11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 12 devices SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:02: ioport range 0x1000-0x1005 could not be reserved pnp: 00:02: ioport range 0x1008-0x100f could not be reserved pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved pnp: 00:03: ioport range 0x1006-0x1007 has been reserved pnp: 00:03: ioport range 0x100a-0x1059 could not be reserved pnp: 00:03: ioport range 0x1060-0x107f has been reserved pnp: 00:03: ioport range 0x1080-0x10bf has been reserved pnp: 00:03: ioport range 0x10c0-0x10df has been reserved pnp: 00:08: ioport range 0x900-0x90f has been reserved pnp: 00:08: ioport range 0x910-0x91f has been reserved pnp: 00:08: ioport range 0x920-0x92f has been reserved pnp: 00:08: ioport range 0x930-0x93f has been reserved pnp: 00:08: ioport range 0x940-0x97f has been reserved pnp: 00:0b: ioport range 0x7b0-0x7bb has been reserved pnp: 00:0b: ioport range 0x7c0-0x7df has been reserved pnp: 00:0b: ioport range 0xbb0-0xbbb has been reserved pnp: 00:0b: ioport range 0xbc0-0xbdf has been reserved pnp: 00:0b: ioport range 0xfb0-0xfbb has been reserved pnp: 00:0b: ioport range 0xfc0-0xfdf has been reserved pnp: 00:0b: ioport range 0x13b0-0x13bb has been reserved pnp: 00:0b: ioport range 0x13c0-0x13df has been reserved PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 PCI: Failed to allocate I/O resource #7:1000@10000 for 0000:00:1e.0 PCI: Bus 4, cardbus bridge: 0000:03:01.0 IO window: 00001400-000014ff IO window: 00001800-000018ff PREFETCH window: 50000000-51ffffff MEM window: 52000000-53ffffff PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: dfd00000-dfdfffff PREFETCH window: 50000000-51ffffff PCI: Setting latency timer of device 0000:00:1e.0 to 64 PCI: Enabling device 0000:03:01.0 (0000 -> 0003) ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 16 Simple Boot Flag at 0x79 set to 0x1 Machine check exception polling timer started. audit: initializing netlink socket (disabled) audit(1146979824.844:1): initialized Installing knfsd (copyright (C) 1996 okir@monad.swb.de). Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered lp: driver loaded but no devices found i8k: unable to get SMM BIOS version Dell laptop SMM driver v1.14 21/02/2005 Massimo Dal Zotto (dz@debian.org) Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 915GM Chipset. agpgart: Detected 7932K stolen memory. agpgart: AGP aperture is 256M @ 0xc0000000 [drm] Initialized drm 1.0.1 20051102 ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) ACPI: Lid Switch [LID] ACPI: Power Button (CM) [PBTN] ACPI: Sleep Button (CM) [SBTN] ACPI: Video Device [VID] (multi-head: yes rom: no post: no) ACPI: Video Device [VID] (multi-head: yes rom: no post: no) ACPI: Video Device [VID2] (multi-head: yes rom: no post: no) ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Thermal Zone [THM] (40 C) PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled ACPI: PCI Interrupt 0000:00:1e.3[B] -> GSI 17 (level, low) -> IRQ 17 ACPI: PCI interrupt for device 0000:00:1e.3 disabled mice: PS/2 mouse device common for all mice Floppy drive(s): fd0 is 1.44M input: AT Translated Set 2 keyboard as /class/input/input0 input: PS/2 Mouse as /class/input/input1 input: AlpsPS/2 ALPS GlidePoint as /class/input/input2 floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize b44.c:v0.97 (Nov 30, 2005) ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18 eth0: Broadcom 4400 10/100BaseT Ethernet 00:12:3f:d7:19:87 PPP generic driver version 2.4.2 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ide0: I/O resource 0x1F0-0x1F7 not free. ide0: ports already in use, skipping probe Probing IDE interface ide1... hdc: PHILIPS CD-RW/DVD-ROM SCB5265, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache Uniform CD-ROM driver Revision: 3.20 libata version 1.20 loaded. ata_piix 0000:00:1f.2: version 1.05 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 17 ata: 0x170 IDE port busy PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xBFA0 irq 14 ata1: dev 0 cfg 49:2b00 82:346b 83:5b68 84:4003 85:3469 86:1a08 87:4003 88:203f ata1: dev 0 ATA-6, max UDMA/100, 58605120 sectors: LBA ata1(0): applying bridge limits ata1: dev 0 configured for UDMA/100 scsi0 : ata_piix Vendor: ATA Model: FUJITSU MHS2030A Rev: 8004 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 58605120 512-byte hdwr sectors (30006 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 58605120 512-byte hdwr sectors (30006 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda sd 0:0:0:0: Attached scsi generic sg0 type 0 ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, low) -> IRQ 18 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[dfdfc800-dfdfcfff] Max Packet=[2048] IR/IT contexts=[4/4] ieee1394: raw1394: /dev/raw1394 device initialized ACPI: PCI Interrupt 0000:03:01.0[A] -> GSI 19 (level, low) -> IRQ 16 Yenta: CardBus bridge found at 0000:03:01.0 [1028:0188] Yenta: ISA IRQ mask 0x04b8, PCI irq 16 Socket status: 30000006 pcmcia: parent PCI bridge Memory window: 0xdfd00000 - 0xdfdfffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff Intel ISA PCIC probe: not found. Databook TCIC-2 PCMCIA probe: not found. usbmon: debugfs is not available ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 16 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:1d.7: irq 19, io mem 0xffa80800 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v2.3 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.0: irq 19, io base 0x0000bf80 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000bf60 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000bf40 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 16 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000bf20 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver oprofile: using NMI interrupt. NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 786432 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered ip_conntrack version 2.4 (7168 buckets, 57344 max) - 172 bytes per conntrack TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode EXT3-fs: sda3: orphan cleanup on readonly fs kjournald starting. Commit interval 5 seconds ext3_orphan_cleanup: deleting unreferenced inode 2910672 EXT3-fs: sda3: 1 orphan inode deleted EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 248k freed ieee1394: Host added: ID:BUS[0-00:1023] GUID[374fc0000f54f8e1] Adding 506036k swap on /dev/sda2. Priority:-1 extents:1 across:506036k EXT3 FS on sda3, internal journal ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, 1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver, 1.1.2mprq ipw2200: Copyright(c) 2003-2006 Intel Corporation ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 17 (level, low) -> IRQ 17 ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection ipw2200: Detected geography ZZM (11 802.11bg channels, 0 802.11a channels) ACPI: PCI Interrupt 0000:00:1e.2[A] -> GSI 16 (level, low) -> IRQ 19 PCI: Setting latency timer of device 0000:00:1e.2 to 64 intel8x0_measure_ac97_clock: measured 55497 usecs intel8x0: clocking to 48000 intelfb: Framebuffer driver for Intel(R) 830M/845G/852GM/855GM/865G/915G/915GM chipsets intelfb: Version 0.9.2 ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 19 intelfb: 00:02.0: Intel(R) 915GM, aperture size 128MB, stolen memory 8060kB intelfb: Non-CRT device is enabled ( LVDS port ). Disabling mode switching. intelfb: Video mode must be programmed at boot time. pcmcia: Detected deprecated PCMCIA ioctl usage. pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools. pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details. cs: IO port probe 0xc00-0xcff: excluding 0xcf8-0xcff cs: IO port probe 0x800-0x8ff: clean. cs: IO port probe 0x100-0x4ff: excluding 0x3f0-0x3f7 cs: IO port probe 0xa00-0xaff: clean. mtrr: no more MTRRs available ieee80211_crypt: registered algorithm 'WEP'