root@OpenWrt:/lib/firmware# insmod acx
acx: this driver is still EXPERIMENTAL
acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion
acx: compiled to use 16bit I/O access only (compatibility mode)
acx: running on a BIG-ENDIAN CPU
acx: PCI module v0.3.36 initialized, waiting for cards to probe...
acx: found ACX111-based wireless network card at 0000:00:02.0, irq:14, phymem1:0x11420000, phymem2:0x11400000, mem1:0xb1420000, mem1_size:8192, mem2:0xb1400000, mem2_size:131072
initial debug setting is 0x000A
using IRQ 14
acx: need to load firmware for acx111 chipset with radio ID 16, please provide via firmware hotplug:
acx: either one file only (<c>ombined firmware image file, radio-specific) or two files (radio-less base image file *plus* separate <r>adio-specific extension file)
requesting firmware image 'tiacx111c16'
acx_write_fw (main/combined): 0
acx_validate_fw (main/combined): 0
initializing max packet templates
dump queue head (from card):
len: 24
tx_memory_block_address: 19060
rx_memory_block_address: 13560
tx1_queue address: 12A94
rx1_queue address: 12754
NVS_vendor_offs:01CD probe_delay:200 eof_memory:1114112
CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01
AntennaID:00 Len:02 Data:01 02 
PowerLevelID:01 Len:02 Data:001E 000A 
DataRatesID:02 Len:05 Data:02 04 11 22 44 
DomainID:03 Len:06 Data:41 20 30 31 32 40 
ProductID:04 Len:09 Data:TI ACX100
ManufacturerID:05 Len:07 Data:TI Test
get_mask 0x00004182, set_mask 0x00000000
don't know how to get sensitivity for radio type 0x16
got sensitivity value 0
got antenna value 0x4A
got regulatory domain 0x41
get_mask 0x00000000, set_mask 0x00000000 - after update
new ratevector: 82 84 0B 0C 12 16 18 24 2C 30 48 60 6C
setting RXconfig to 2010:0FDD
acx: === chipset TNETW1130, radio type 0x16 (Radia), form factor 0x01 ((mini-)PCI / CardBus), EEPROM version 0x05: uploaded firmware 'Rev 1.2.1.34' ===
creating /proc entry driver/acx_wlan0
creating /proc entry driver/acx_wlan0_diag
creating /proc entry driver/acx_wlan0_eeprom
creating /proc entry driver/acx_wlan0_phy
acx v0.3.36: net device wlan0, driver compiled against wireless extensions 22 and Linux 2.6.22-rc4
root@OpenWrt:/lib/firmware# ifconfig wlan0 up
acx_set_status(1):SCANNING
updating initial settings on iface activation
get_mask 0x00000000, set_mask 0x0036EEFE
important setting has been changed. Need to update packet templates, too
updating packet templates
updating Tx fallback to 1 retries
updating transmit power: 15 dBm
updating antenna value: 0x4A
updating Energy Detect (ED) threshold: 0
acx111 doesn't support ED!
updating Channel Clear Assessment (CCA) value: 0x00
acx111 doesn't support CCA!
updating channel to: 1
updating: enable Tx
updating: enable Rx on channel: 1
updating short retry limit: 7, long retry limit: 4
updating tx MSDU lifetime: 4096
updating regulatory domain: 0x41
setting RXconfig to 2010:0FDD
updating WEP key settings
setting WEP key 0 as default
acx_set_status(1):SCANNING
starting radio scan
get_mask 0x00000000, set_mask 0x00000000 - after update
get_mask 0x00000000, set_mask 0x00000040
setting RXconfig to 2010:0FDD
root@OpenWrt:/lib/firmware# get_mask 0x00000000, set_mask 0x00000000 - after update
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (1 sec)
sta_list_add: sta=00:04:E2:CD:C2:32
acx_i_timer: adev->status=1 (SCANNING)
continuing scan (2 sec)
scan table: SSID=" " CH=6 SIR=14 SNR=0
peer_cap 0x0431, needed_cap 0x0001
found station with empty or single-space (hidden) SSID, considering for assoc attempt
matching station found: 00:04:E2:CD:C2:32, joining
sending authentication1 request (auth algo 0), awaiting response
acx_set_status(2):WAIT_AUTH
rates_basic:0003, rates_supported:1FFF
BSS_Type = 2
JoinBSSID MAC:00:04:E2:CD:C2:32
AUTHEN adev->addr=00:A0:C5:94:FD:96 a1=00:A0:C5:94:FD:96 a2=00:04:E2:CD:C2:32 a3=00:04:E2:CD:C2:32 adev->bssid=00:04:E2:CD:C2:32
auth algorithm 0, auth sequence 2, status 0
acx_set_status(3):AUTHENTICATED
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"
wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
acx_i_timer: adev->status=3 (AUTHENTICATED)
resend assoc request (attempt 2)
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"
wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
acx_i_timer: adev->status=3 (AUTHENTICATED)
resend assoc request (attempt 3)
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"
wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
acx_i_timer: adev->status=3 (AUTHENTICATED)
resend assoc request (attempt 4)
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"
wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
ifconfiacx_i_timer: adev->status=3 (AUTHENTICATED)
resend assoc request (attempt 5)
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"
wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
g acx_i_timer: adev->status=3 (AUTHENTICATED)
resend assoc request (attempt 6)
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"
wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
wlan0 downacx_i_timer: adev->status=3 (AUTHENTICATED)
resend assoc request (attempt 7)
sending association request, awaiting response. NOT ASSOCIATED YET
association: requesting caps 0x2100, ESSID "STA94FD96"

wlan0: association FAILED: peer sent Status Code 13 (Responding station doesnt support specified auth algorithm -- maybe WEP auth Open vs. Restricted?)
get_mask 0x00000000, set_mask 0x00000040
setting RXconfig to 2010:0FDD
get_mask 0x00000000, set_mask 0x00000000 - after update
acx_set_status(0):STOPPED
closed device