[ 0.000000] Linux version 2.6.20-16-generic (root@king) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Wed May 23 00:30:47 UTC 2007 (Ubuntu 2.6.20-16.28-generic) [ 0.000000] Command line: root=/dev/sda5 ro quiet splash [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000003f688c00 (usable) [ 0.000000] BIOS-e820: 000000003f688c00 - 000000003f68ac00 (ACPI NVS) [ 0.000000] BIOS-e820: 000000003f68ac00 - 000000003f68cc00 (ACPI data) [ 0.000000] BIOS-e820: 000000003f68cc00 - 0000000040000000 (reserved) [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved) [ 0.000000] BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) [ 0.000000] Entering add_active_range(0, 0, 160) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 259720) 1 entries of 3200 used [ 0.000000] end_pfn_map = 1048576 [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v002 DELL ) @ 0x00000000000feb00 [ 0.000000] ACPI: XSDT (v001 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd263 [ 0.000000] ACPI: FADT (v003 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd35b [ 0.000000] ACPI: SSDT (v001 DELL st_ex 0x00001000 INTL 0x20050309) @ 0x00000000fffca767 [ 0.000000] ACPI: MADT (v001 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd44f [ 0.000000] ACPI: BOOT (v001 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd4c1 [ 0.000000] ACPI: ASF! (v016 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd4e9 [ 0.000000] ACPI: MCFG (v001 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd550 [ 0.000000] ACPI: HPET (v001 DELL DXC051 0x00000007 ASL 0x00000061) @ 0x00000000000fd58e [ 0.000000] ACPI: DSDT (v001 DELL dt_ex 0x00001000 INTL 0x20050309) @ 0x0000000000000000 [ 0.000000] No NUMA configuration found [ 0.000000] Faking a node at 0000000000000000-000000003f688000 [ 0.000000] Entering add_active_range(0, 0, 160) 0 entries of 3200 used [ 0.000000] Entering add_active_range(0, 256, 259720) 1 entries of 3200 used [ 0.000000] Bootmem setup node 0 0000000000000000-000000003f688000 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] DMA32 4096 -> 1048576 [ 0.000000] Normal 1048576 -> 1048576 [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0 -> 160 [ 0.000000] 0: 256 -> 259720 [ 0.000000] On node 0 totalpages: 259624 [ 0.000000] DMA zone: 56 pages used for memmap [ 0.000000] DMA zone: 1086 pages reserved [ 0.000000] DMA zone: 2858 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 3494 pages used for memmap [ 0.000000] DMA32 zone: 252130 pages, LIFO batch:31 [ 0.000000] Normal zone: 0 pages used for memmap [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] Processor #0 (Bootup-CPU) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) [ 0.000000] Processor #1 [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 8, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Setting APIC routing to physical flat [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Nosave address range: 00000000000a0000 - 00000000000f0000 [ 0.000000] Nosave address range: 00000000000f0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000) [ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs [ 0.000000] PERCPU: Allocating 34048 bytes of per cpu data [ 0.000000] Built 1 zonelists. Total pages: 254988 [ 0.000000] Kernel command line: root=/dev/sda5 ro quiet splash [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 15.636252] Console: colour VGA+ 80x25 [ 15.636726] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 15.637152] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes) [ 15.637251] Checking aperture... [ 15.637260] Calgary: detecting Calgary via BIOS EBDA area [ 15.637263] Calgary: Unable to locate Rio Grande table in EBDA - bailing! [ 15.647279] Memory: 1011364k/1038880k available (2217k kernel code, 27132k reserved, 1162k data, 304k init) [ 15.725681] Calibrating delay using timer specific routine.. 5991.46 BogoMIPS (lpj=11982931) [ 15.725744] Security Framework v1.0.0 initialized [ 15.725749] SELinux: Disabled at boot. [ 15.725777] Mount-cache hash table entries: 256 [ 15.725942] CPU: Trace cache: 12K uops, L1 D cache: 16K [ 15.725945] CPU: L2 cache: 2048K [ 15.725948] CPU 0/0 -> Node 0 [ 15.725950] using mwait in idle threads. [ 15.725952] CPU: Physical Processor ID: 0 [ 15.725953] CPU: Processor Core ID: 0 [ 15.725964] CPU0: Thermal monitoring enabled (TM1) [ 15.725977] SMP alternatives: switching to UP code [ 15.726251] Early unpacking initramfs... done [ 16.027862] ACPI: Core revision 20060707 [ 16.043542] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT. [ 16.151837] Using local APIC timer interrupts. [ 16.185239] result 12468726 [ 16.185241] Detected 12.468 MHz APIC timer. [ 16.185686] SMP alternatives: switching to SMP code [ 16.185819] Booting processor 1/2 APIC 0x1 [ 16.196445] Initializing CPU#1 [ 16.273378] Calibrating delay using timer specific routine.. 5985.27 BogoMIPS (lpj=11970553) [ 16.273393] CPU: Trace cache: 12K uops, L1 D cache: 16K [ 16.273396] CPU: L2 cache: 2048K [ 16.273399] CPU 1/1 -> Node 0 [ 16.273402] CPU: Physical Processor ID: 0 [ 16.273403] CPU: Processor Core ID: 0 [ 16.273415] CPU1: Thermal monitoring enabled (TM1) [ 16.273785] Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03 [ 16.277401] Brought up 2 CPUs [ 16.277444] time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer. [ 16.277447] time.c: Detected 2992.503 MHz processor. [ 16.313324] migration_cost=5 [ 16.313707] Time: 19:06:03 Date: 05/07/107 [ 16.313749] NET: Registered protocol family 16 [ 16.313844] ACPI: bus type pci registered [ 16.313852] PCI: Using configuration type 1 [ 16.368554] ACPI: Interpreter enabled [ 16.368557] ACPI: Using IOAPIC for interrupt routing [ 16.372635] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 16.372642] PCI: Probing PCI hardware (bus 00) [ 16.372666] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0 [ 16.379277] Boot video device is 0000:00:02.0 [ 16.380120] PCI: Firmware left 0000:03:08.0 e100 interrupts enabled, disabling [ 16.380258] PCI: Transparent bridge - 0000:00:1e.0 [ 16.380311] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 17.376090] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI4._PRT] [ 17.383727] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT] [ 17.398387] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] [ 17.448141] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15) [ 17.449189] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 15) [ 17.450306] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 15) [ 17.451396] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled. [ 17.452467] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 9 10 11 12 15) [ 17.453611] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 *10 11 12 15) [ 17.454655] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *9 10 11 12 15) [ 17.455748] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 *4 5 6 7 9 10 11 12 15) [ 17.457498] Linux Plug and Play Support v0.97 (c) Adam Belay [ 17.457509] pnp: PnP ACPI init [ 17.496224] pnp: PnP ACPI: found 8 devices [ 17.496282] PCI: Using ACPI for IRQ routing [ 17.496285] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 17.496368] NET: Registered protocol family 8 [ 17.496371] NET: Registered protocol family 20 [ 17.496384] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 17.496389] hpet0: 3 64-bit timers, 14318180 Hz [ 17.497410] PCI-GART: No AMD northbridge found. [ 17.511502] pnp: 00:01: ioport range 0x800-0x85f could not be reserved [ 17.511505] pnp: 00:01: ioport range 0xc00-0xc7f has been reserved [ 17.511508] pnp: 00:01: ioport range 0x860-0x8ff has been reserved [ 17.511519] pnp: 00:07: ioport range 0x100-0x1fe could not be reserved [ 17.511522] pnp: 00:07: ioport range 0x200-0x277 has been reserved [ 17.511524] pnp: 00:07: ioport range 0x280-0x2e7 has been reserved [ 17.511527] pnp: 00:07: ioport range 0x2e8-0x2ef has been reserved [ 17.511530] pnp: 00:07: ioport range 0x2f0-0x2f7 has been reserved [ 17.511532] pnp: 00:07: ioport range 0x2f8-0x2ff has been reserved [ 17.511535] pnp: 00:07: ioport range 0x300-0x377 could not be reserved [ 17.511538] pnp: 00:07: ioport range 0x380-0x3bb has been reserved [ 17.511927] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0 [ 17.511932] PCI: Bridge: 0000:00:01.0 [ 17.511933] IO window: disabled. [ 17.511937] MEM window: efd00000-efdfffff [ 17.511940] PREFETCH window: disabled. [ 17.511944] PCI: Bridge: 0000:00:1c.0 [ 17.511945] IO window: disabled. [ 17.511950] MEM window: efc00000-efcfffff [ 17.511954] PREFETCH window: disabled. [ 17.511959] PCI: Bridge: 0000:00:1e.0 [ 17.511962] IO window: d000-dfff [ 17.511967] MEM window: efb00000-efbfffff [ 17.511970] PREFETCH window: disabled. [ 17.511987] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 17.511993] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 17.512010] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 17.512016] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 17.512026] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 17.512068] NET: Registered protocol family 2 [ 17.552721] IP route cache hash table entries: 32768 (order: 6, 262144 bytes) [ 17.552920] TCP established hash table entries: 131072 (order: 9, 2097152 bytes) [ 17.553949] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 17.554704] TCP: Hash tables configured (established 131072 bind 65536) [ 17.554709] TCP reno registered [ 17.568839] checking if image is initramfs... it is [ 18.154355] Freeing initrd memory: 6817k freed [ 18.159376] Simple Boot Flag at 0x7a set to 0x1 [ 18.159998] audit: initializing netlink socket (disabled) [ 18.160016] audit(1181243164.500:1): initialized [ 18.160231] VFS: Disk quotas dquot_6.5.1 [ 18.160256] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 18.160326] io scheduler noop registered [ 18.160329] io scheduler anticipatory registered [ 18.160331] io scheduler deadline registered [ 18.160349] io scheduler cfq registered (default) [ 18.180577] PCI: Setting latency timer of device 0000:00:01.0 to 64 [ 18.180615] assign_interrupt_mode Found MSI capability [ 18.180619] Allocate Port Service[0000:00:01.0:pcie00] [ 18.180714] PCI: Setting latency timer of device 0000:00:1c.0 to 64 [ 18.180756] assign_interrupt_mode Found MSI capability [ 18.180758] Allocate Port Service[0000:00:1c.0:pcie00] [ 18.180797] Allocate Port Service[0000:00:1c.0:pcie02] [ 18.209536] Real Time Clock Driver v1.12ac [ 18.209590] Linux agpgart interface v0.102 (c) Dave Jones [ 18.209593] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 18.210203] mice: PS/2 mouse device common for all mice [ 18.210921] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 18.211182] input: Macintosh mouse button emulation as /class/input/input0 [ 18.211225] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 18.211230] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 18.211492] PNP: No PS/2 controller found. Probing ports directly. [ 18.214310] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 18.214316] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 18.214418] TCP cubic registered [ 18.214428] NET: Registered protocol family 1 [ 18.214562] ACPI: (supports S0 S1 S3 S4 S5) [ 18.214611] Magic number: 11:604:141 [ 18.214787] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 18.214842] Freeing unused kernel memory: 304k freed [ 19.424225] Capability LSM initialized [ 19.516545] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707] [ 19.516559] ACPI Exception (acpi_processor-0677): AE_NOT_FOUND, Processor Device is not present [20060707] [ 20.196619] usbcore: registered new interface driver usbfs [ 20.196652] usbcore: registered new interface driver hub [ 20.196691] usbcore: registered new device driver usb [ 20.197996] USB Universal Host Controller Interface driver v3.0 [ 20.198062] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 21 [ 20.198080] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 20.198085] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 20.198248] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 20.198279] uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80 [ 20.198427] usb usb1: configuration #1 chosen from 1 choice [ 20.198462] hub 1-0:1.0: USB hub found [ 20.198471] hub 1-0:1.0: 2 ports detected [ 20.261752] SCSI subsystem initialized [ 20.269002] libata version 2.20 loaded. [ 20.283513] e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI [ 20.283517] e100: Copyright(c) 1999-2006 Intel Corporation [ 20.299477] ieee1394: Initialized config rom entry `ip1394' [ 20.303255] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 22 [ 20.303275] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 20.303281] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 20.303316] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 20.303348] uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60 [ 20.303485] usb usb2: configuration #1 chosen from 1 choice [ 20.303521] hub 2-0:1.0: USB hub found [ 20.303530] hub 2-0:1.0: 2 ports detected [ 20.411203] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18 [ 20.411221] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 20.411227] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 20.411267] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 20.411301] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40 [ 20.411458] usb usb3: configuration #1 chosen from 1 choice [ 20.411508] hub 3-0:1.0: USB hub found [ 20.411519] hub 3-0:1.0: 2 ports detected [ 20.519127] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23 [ 20.519143] PCI: Setting latency timer of device 0000:00:1d.3 to 64 [ 20.519149] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 20.519182] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 20.519213] uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20 [ 20.519344] usb usb4: configuration #1 chosen from 1 choice [ 20.519394] hub 4-0:1.0: USB hub found [ 20.519407] hub 4-0:1.0: 2 ports detected [ 20.546982] usb 1-1: new low speed USB device using uhci_hcd and address 2 [ 20.629828] ICH7: IDE controller at PCI slot 0000:00:1f.1 [ 20.629841] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16 [ 20.629857] ICH7: chipset revision 1 [ 20.629859] ICH7: not 100% native mode: will probe irqs later [ 20.629870] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio [ 20.629884] Probing IDE interface ide0... [ 20.736118] usb 1-1: configuration #1 chosen from 1 choice [ 20.986793] usb 3-1: new low speed USB device using uhci_hcd and address 2 [ 21.218003] usb 3-1: configuration #1 chosen from 1 choice [ 21.221045] usbcore: registered new interface driver hiddev [ 21.234897] input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input1 [ 21.234917] input: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.0-1 [ 21.255872] input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input2 [ 21.255880] input: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.0-1 [ 21.283951] input: Microsoft Corporation Microsoft � Laser Mouse 6000 as /class/input/input3 [ 21.283978] input: USB HID v1.11 Mouse [Microsoft Corporation Microsoft � Laser Mouse 6000] on usb-0000:00:1d.2-1 [ 21.283992] usbcore: registered new interface driver usbhid [ 21.283996] drivers/usb/input/hid-core.c: v2.6:USB HID core driver [ 21.362847] hda: HL-DT-STCD-RW/DVD-ROM GCC-4244N, ATAPI CD/DVD-ROM drive [ 21.699513] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 [ 21.699637] ACPI: PCI Interrupt 0000:03:08.0[A] -> GSI 20 (level, low) -> IRQ 20 [ 21.718900] e100: eth0: e100_probe: addr 0xefbfb000, irq 20, MAC addr 00:12:3F:B6:9A:ED [ 21.719059] ACPI: PCI Interrupt 0000:03:0a.0[A] -> GSI 18 (level, low) -> IRQ 18 [ 21.769299] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18] MMIO=[efbfa800-efbfafff] Max Packet=[2048] IR/IT contexts=[4/8] [ 21.769374] ahci 0000:00:1f.2: version 2.1 [ 21.769400] ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 20 [ 22.769986] PCI: Setting latency timer of device 0000:00:1f.2 to 64 [ 22.769995] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode [ 22.769999] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part [ 22.770123] ata1: SATA max UDMA/133 cmd 0xffffc20000040d00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 20 [ 22.770213] ata2: SATA max UDMA/133 cmd 0xffffc20000040d80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 20 [ 22.770297] ata3: SATA max UDMA/133 cmd 0xffffc20000040e00 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 20 [ 22.770383] ata4: SATA max UDMA/133 cmd 0xffffc20000040e80 ctl 0x0000000000000000 bmdma 0x0000000000000000 irq 20 [ 22.770394] scsi0 : ahci [ 23.038035] ieee1394: Host added: ID:BUS[0-00:1023] GUID[80b600129aed3f00] [ 23.253762] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 23.255861] ata1.00: ata_hpa_resize 1: sectors = 156250000, hpa_sectors = 156250000 [ 23.255867] ata1.00: ATA-7: Maxtor 6L080M0, BACE1G10, max UDMA/133 [ 23.255871] ata1.00: 156250000 sectors, multi 8: LBA48 NCQ (depth 31/32) [ 23.258848] ata1.00: ata_hpa_resize 1: sectors = 156250000, hpa_sectors = 156250000 [ 23.258853] ata1.00: configured for UDMA/133 [ 23.258867] scsi1 : ahci [ 23.569596] ata2: SATA link down (SStatus 0 SControl 300) [ 23.569610] scsi2 : ahci [ 23.881450] ata3: SATA link down (SStatus 0 SControl 300) [ 23.881463] scsi3 : ahci [ 24.193302] ata4: SATA link down (SStatus 0 SControl 300) [ 24.193425] scsi 0:0:0:0: Direct-Access ATA Maxtor 6L080M0 BACE PQ: 0 ANSI: 5 [ 24.228340] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 21 [ 24.228363] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 24.228369] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 24.228629] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 24.228667] ehci_hcd 0000:00:1d.7: debug port 1 [ 24.228675] PCI: cache line size of 128 is not supported by device 0000:00:1d.7 [ 24.228684] ehci_hcd 0000:00:1d.7: irq 21, io mem 0xffa80800 [ 24.232571] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 24.232712] usb usb5: configuration #1 chosen from 1 choice [ 24.232760] hub 5-0:1.0: USB hub found [ 24.232770] hub 5-0:1.0: 8 ports detected [ 24.239970] SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) [ 24.239987] sda: Write Protect is off [ 24.239990] sda: Mode Sense: 00 3a 00 00 [ 24.240013] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 24.240073] SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB) [ 24.240087] sda: Write Protect is off [ 24.240090] sda: Mode Sense: 00 3a 00 00 [ 24.240113] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 24.240117] sda: sda1 sda2 sda3 < sda5<6>usb 3-1: USB disconnect, address 2 [ 24.305136] sda6 > [ 24.305284] sd 0:0:0:0: Attached scsi disk sda [ 24.309068] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 24.348965] hda: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) [ 24.348981] Uniform CD-ROM driver Revision: 3.20 [ 24.425257] usb 1-1: USB disconnect, address 2 [ 24.605998] Attempting manual resume [ 24.606002] swsusp: Resume From Partition 8:6 [ 24.606004] PM: Checking swsusp image. [ 24.606104] PM: Resume from disk failed. [ 24.621698] kjournald starting. Commit interval 5 seconds [ 24.621711] EXT3-fs: mounted filesystem with ordered data mode. [ 25.161235] usb 1-1: new low speed USB device using uhci_hcd and address 3 [ 25.342595] usb 1-1: configuration #1 chosen from 1 choice [ 25.359619] input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input4 [ 25.359633] input: USB HID v1.11 Keyboard [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.0-1 [ 25.380611] input: Microsoft Comfort Curve Keyboard 2000 as /class/input/input5 [ 25.380622] input: USB HID v1.11 Device [Microsoft Comfort Curve Keyboard 2000] on usb-0000:00:1d.0-1 [ 25.621197] usb 3-1: new low speed USB device using uhci_hcd and address 3 [ 25.844448] usb 3-1: configuration #1 chosen from 1 choice [ 25.875434] input: Microsoft Corporation Microsoft � Laser Mouse 6000 as /class/input/input6 [ 25.875462] input: USB HID v1.11 Mouse [Microsoft Corporation Microsoft � Laser Mouse 6000] on usb-0000:00:1d.2-1 [ 30.099917] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex [ 31.506461] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 31.508661] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 31.812411] agpgart: Detected an Intel 945G Chipset. [ 31.813105] agpgart: Detected 7932K stolen memory. [ 31.828644] agpgart: AGP aperture is 256M @ 0xd0000000 [ 31.833546] NET: Registered protocol family 17 [ 31.937466] input: PC Speaker as /class/input/input7 [ 32.173985] usbcore: registered new interface driver xpad [ 32.173991] drivers/usb/input/xpad.c: driver for Xbox controllers v0.1.6 [ 32.305284] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 32.305312] PCI: Setting latency timer of device 0000:00:1b.0 to 64 [ 32.950125] fuse init (API version 7.8) [ 33.032116] lp: driver loaded but no devices found [ 33.102784] Adding 1959888k swap on /dev/disk/by-uuid/230ba095-283d-4a71-a7b3-17bec2776b32. Priority:-1 extents:1 across:1959888k [ 33.278418] EXT3 FS on sda5, internal journal [ 33.445416] NTFS driver 2.1.28 [Flags: R/O MODULE]. [ 33.503083] NTFS volume version 3.1. [ 35.265144] NET: Registered protocol family 10 [ 35.265278] lo: Disabled Privacy Extensions [ 39.287992] input: Power Button (FF) as /class/input/input8 [ 39.288037] ACPI: Power Button (FF) [PWRF] [ 39.288092] input: Power Button (CM) as /class/input/input9 [ 39.288130] ACPI: Power Button (CM) [VBTN] [ 39.385120] Using specific hotkey driver [ 39.953324] ibm_acpi: ec object not found [ 40.081134] No dock devices found. [ 40.170899] pcc_acpi: loading... [ 43.345338] ppdev: user-space parallel port driver [ 44.708845] Bluetooth: Core ver 2.11 [ 44.708921] NET: Registered protocol family 31 [ 44.708925] Bluetooth: HCI device and connection manager initialized [ 44.708929] Bluetooth: HCI socket layer initialized [ 44.735182] Bluetooth: L2CAP ver 2.8 [ 44.735188] Bluetooth: L2CAP socket layer initialized [ 44.816676] Bluetooth: RFCOMM socket layer initialized [ 44.816699] Bluetooth: RFCOMM TTY layer initialized [ 44.816702] Bluetooth: RFCOMM ver 1.8 [ 57.565997] eth0: no IPv6 routers present [ 4365.210566] [drm] Initialized drm 1.1.0 20060810 [ 4365.213261] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16 [ 4365.213343] [drm] Initialized i915 1.6.0 20060119 on minor 0