Linux version 2.6.21-gentoo-r3 (root@proprio-laptop) (gcc version 4.1.1 (Gentoo 4.1.1-r3)) #1 SMP Fri Jun 22 13:31:41 Local time zone must be set--see zic BIOS-provided physical RAM map: sanitize start sanitize end copy_e820_map() start: 0000000000000000 size: 000000000009dc00 end: 000000000009dc00 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 000000000009dc00 size: 0000000000002400 end: 00000000000a0000 type: 2 copy_e820_map() start: 00000000000d0000 size: 0000000000030000 end: 0000000000100000 type: 2 copy_e820_map() start: 0000000000100000 size: 0000000037d90000 end: 0000000037e90000 type: 1 copy_e820_map() type is E820_RAM copy_e820_map() start: 0000000037e90000 size: 000000000000a000 end: 0000000037e9a000 type: 3 copy_e820_map() start: 0000000037e9a000 size: 0000000000066000 end: 0000000037f00000 type: 4 copy_e820_map() start: 0000000037f00000 size: 0000000008100000 end: 0000000040000000 type: 2 copy_e820_map() start: 00000000e0000000 size: 0000000010000000 end: 00000000f0000000 type: 2 copy_e820_map() start: 00000000fec00000 size: 0000000000010000 end: 00000000fec10000 type: 2 copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2 copy_e820_map() start: 00000000fff80000 size: 0000000000080000 end: 0000000100000000 type: 2 BIOS-e820: 0000000000000000 - 000000000009dc00 (usable) BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000037e90000 (usable) BIOS-e820: 0000000037e90000 - 0000000037e9a000 (ACPI data) BIOS-e820: 0000000037e9a000 - 0000000037f00000 (ACPI NVS) BIOS-e820: 0000000037f00000 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 894MB LOWMEM available. found SMP MP-table at 000f8110 Entering add_active_range(0, 0, 229008) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 229008 HighMem 229008 -> 229008 early_node_map[1] active PFN ranges 0: 0 -> 229008 On node 0 totalpages: 229008 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1757 pages used for memmap Normal zone: 223155 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap DMI present. Using APIC driver default ACPI: RSDP 000F8040, 0014 (r0 ACRSYS) ACPI: RSDT 37E91CA5, 0038 (r1 ACRSYS ACRPRDCT 6040000 LTP 0) ACPI: FACP 37E99C04, 0074 (r1 ATI Bowfin 6040000 ATI F4240) ACPI: DSDT 37E91CDD, 7F27 (r1 Acer Navarro 6040000 MSFT 3000000) ACPI: FACS 37E9AFC0, 0040 ACPI: SLIC 37E99C78, 0176 (r1 ACRSYS ACRPRDCT 6040000 LOHR 0) ACPI: APIC 37E99DEE, 0054 (r1 PTLTD APIC 6040000 LTP 0) ACPI: MCFG 37E99E42, 003C (r1 PTLTD MCFG 6040000 LTP 0) ACPI: SSDT 37E99E7E, 0182 (r1 PTLTD POWERNOW 6040000 LTP 1) ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:8 APIC version 16 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) Processor #1 15:8 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 33, address 0xfec00000, GSI 0-23 ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Built 1 zonelists. Total pages: 227219 Kernel command line: root=/dev/hda4 mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 1596.040 MHz processor. Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 901076k/916032k available (3774k kernel code, 14476k reserved, 1673k data, 292k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffe16000 - 0xfffff000 (1956 kB) pkmap : 0xff800000 - 0xffc00000 (4096 kB) vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB) lowmem : 0xc0000000 - 0xf7e90000 ( 894 MB) .init : 0xc065c000 - 0xc06a5000 ( 292 kB) .data : 0xc04af99d - 0xc0652130 (1673 kB) .text : 0xc0100000 - 0xc04af99d (3774 kB) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 3194.01 BogoMIPS (lpj=1597005) Mount-cache hash table entries: 512 CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU 0(2) -> Core 0 CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00000410 00002001 00000000 0000001f Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Compat vDSO mapped to ffffe000. Checking 'hlt' instruction... OK. Freeing SMP alternatives: 20k freed ACPI: Core revision 20070126 Parsing all Control Methods: Table [DSDT](id 0001) - 1120 Objects with 83 Devices 295 Methods 43 Regions Parsing all Control Methods: Table [SSDT](id 0002) - 8 Objects with 0 Devices 0 Methods 0 Regions tbxface-0587 [02] tb_load_namespace : ACPI Tables successfully acquired evxfevnt-0091 [02] enable : Transition to ACPI mode successful CPU0: AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02 Booting processor 1/1 eip 2000 Initializing CPU#1 Calibrating delay using timer specific routine.. 3191.57 BogoMIPS (lpj=1595785) CPU: After generic identify, caps: 178bfbff ebd3fbff 00000000 00000000 00002001 00000000 0000001f CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 256K (64 bytes/line) CPU 1(2) -> Core 1 CPU: After all inits, caps: 178bfbff ebd3fbff 00000000 00004410 00002001 00000000 0000001f Intel machine check architecture supported. Intel machine check reporting enabled on CPU#1. CPU1: AMD Turion(tm) 64 X2 Mobile Technology TL-50 stepping 02 Total of 2 processors activated (6385.58 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1 Brought up 2 CPUs migration_cost=1000 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on device 00:18 Setting up standard PCI resources evgpeblk-0952 [04] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9 evgpeblk-1049 [03] ev_initialize_gpe_bloc: Found 6 Wake, Enabled 2 Runtime GPEs in this block Completing Region/Field/Buffer/Package initialization:................................................................................................................................................ Initialized 43/43 Regions 39/39 Fields 36/36 Buffers 26/42 Packages (1137 nodes) Initializing Device/Processor/Thermal objects by executing _INI methods:. Executed 1 _INI methods requiring 0 _STA executions (examined 88 objects) ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:01:05.0 PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB4_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB5_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB4_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BB5_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 10 devices SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 7 of bridge 0000:00:04.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:04.0 PCI: Cannot allocate resource region 9 of bridge 0000:00:04.0 PCI: Cannot allocate resource region 7 of bridge 0000:00:05.0 PCI: Cannot allocate resource region 8 of bridge 0000:00:05.0 pnp: 00:01: iomem range 0xe0000000-0xefffffff could not be reserved pnp: 00:01: iomem range 0xfec00000-0xfec00fff could not be reserved pnp: 00:01: iomem range 0xfee00000-0xfee00fff could not be reserved pnp: 00:08: ioport range 0x1080-0x1080 has been reserved pnp: 00:08: ioport range 0x40b-0x40b has been reserved pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:08: ioport range 0x4d6-0x4d6 has been reserved pnp: 00:09: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:09: iomem range 0xfff00000-0xffffffff could not be reserved pnp: 00:09: iomem range 0x0-0xfff could not be reserved PCI: Bridge: 0000:00:01.0 IO window: 9000-9fff MEM window: c0100000-c01fffff PREFETCH window: c8000000-cfffffff PCI: Bridge: 0000:00:04.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 Time: acpi_pm clocksource has been installed. IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bus 7, cardbus bridge: 0000:06:04.0 IO window: 0000a400-0000a4ff IO window: 0000a800-0000a8ff PREFETCH window: 50000000-53ffffff MEM window: 58000000-5bffffff PCI: Bridge: 0000:00:14.4 IO window: a000-afff MEM window: c0200000-c02fffff PREFETCH window: 50000000-53ffffff PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 ACPI: PCI Interrupt 0000:06:04.0[A] -> GSI 20 (level, low) -> IRQ 16 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1572864 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered Machine check exception polling timer started. microcode: CPU0 not a capable Intel processor microcode: CPU1 not a capable Intel processor IA-32 Microcode Update Driver: v1.14a Total HugeTLB memory allocated, 0 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.28 [Flags: R/O]. JFS: nTxBlock = 7040, nTxLock = 56324 SGI XFS with large block numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered PCI: MSI quirk detected. MSI deactivated. Real Time Clock Driver v1.12ac Linux agpgart interface v0.102 (c) Dave Jones Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds). Hangcheck: Using get_cycles(). vesafb: ATI Technologies Inc., MS48, 01.00 (OEM: ATI RADEON XPRESS 200M Series) vesafb: VBE version: 2.0 vesafb: protected mode interface info at c000:53f8 vesafb: pmi: set display start = c00c5466, set palette = c00c54a0 vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 vesafb: no monitor limits have been set vesafb: scrolling: redraw Console: switching to colour frame buffer device 80x30 vesafb: framebuffer at 0xc8000000, mapped to 0xf8c80000, using 6144k, total 16384k fb0: VESA VGA frame buffer device ACPI: AC Adapter [ACAD] (on-line) ACPI: Battery Slot [BAT1] (battery present) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input1 ACPI: Lid Switch [LID] input: Power Button (CM) as /class/input/input2 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input3 ACPI: Sleep Button (CM) [SLPB] ACPI Exception (thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20070126] ACPI: Thermal Zone [THRM] (55 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize loop: loaded (max 8 devices) e100: Intel(R) PRO/100 Network Driver, 3.5.17-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation PPP generic driver version 2.4.2 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) 8139cp 0000:06:01.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip 8139cp 0000:06:01.0: Try the "8139too" driver instead. 8139too Fast Ethernet driver 0.9.28 ACPI: PCI Interrupt 0000:06:01.0[A] -> GSI 21 (level, low) -> IRQ 17 eth0: RealTek RTL8139 at 0xf8c2c000, 00:16:d4:54:e2:97, IRQ 17 eth0: Identified 8139 chip type 'RTL-8100B/8139D' netconsole: not configured, aborting Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 18 ATIIXP: chipset revision 128 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8420-0x8427, BIOS settings: hda:DMA, hdb:DMA ATIIXP: simplex device: DMA disabled ide1: ATIIXP Bus-Master DMA disabled (BIOS) Probing IDE interface ide0... hda: HTS541010G9AT00, ATA DISK drive hdb: MATSHITADVD-RAM UJ-850S, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... Probing IDE interface ide1... hda: max request size: 512KiB hda: 195371568 sectors (100030 MB) w/7539KiB Cache, CHS=16383/255/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 hda3 < hda5 hda6 hda7 > hda4 hdb: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 3ware Storage Controller device driver for Linux v1.26.02.002. Fusion MPT base driver 3.04.04 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.04 ieee1394: raw1394: /dev/raw1394 device initialized usbmon: debugfs is not available ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 19 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.2: irq 19, io mem 0xc0007000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 19, io mem 0xc0005000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 19 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 19, io mem 0xc0006000 usb 1-4: new high speed USB device using ehci_hcd and address 2 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 4 ports detected USB Universal Host Controller Interface driver v3.0 usb 1-4: configuration #1 chosen from 1 choice usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSS0] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice input: AT Translated Set 2 keyboard as /class/input/input4 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com Advanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). ACPI: PCI Interrupt 0000:00:14.2[A] -> GSI 16 (level, low) -> IRQ 18 ALSA device list: #0: HDA ATI SB at 0xc0000000 irq 18 oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 10 IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation ieee80211_crypt: registered algorithm 'NULL' ieee80211_crypt: registered algorithm 'WEP' ieee80211_crypt: registered algorithm 'CCMP' ieee80211_crypt: registered algorithm 'TKIP' powernow-k8: Found 2 AMD Turion(tm) 64 X2 Mobile Technology TL-50 processors (version 2.00.00) powernow-k8: 0 : fid 0x8 (1600 MHz), vid 0x12 powernow-k8: 1 : fid 0x0 (800 MHz), vid 0x1e processor_perflib-0550 [00] processor_get_psd : Invalid _PSD data Using IPI Shortcut mode Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1280b1, caps: 0xa04713/0x204000 input: SynPS/2 Synaptics TouchPad as /class/input/input5 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 292k freed EXT3 FS on hda4, internal journal EXT3-fs: Unrecognized mount option "default" or missing value kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 1052216k swap on /dev/hda6. Priority:-1 extents:1 across:1052216k eth0: link down ADDRCONF(NETDEV_UP): eth0: link is not ready Clocksource tsc unstable (delta = 37496914662 ns)