Linux version 2.6.22-rc6 (root@altix.silihost.hu) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Tue Jun 26 01:43:05 CEST 2007 EFI v1.02 by SGI: SALsystab=0x3002518ae0 ACPI 2.0=0x3002518be0 ACPI: RSDP 3002518BE0, 0024 (r2 SGI) ACPI: XSDT 30027AB2B0, 004C (r1 SGI XSDTSN2 10001 ^A 1) ACPI: APIC 3002518C20, 0044 (r1 SGI APICSN2 10001 ^A 1) ACPI: SRAT 30027AB310, 0078 (r1 SGI SRATSN2 10001 ^A 1) ACPI: SLIT 3002518C80, 002D (r1 SGI SLITSN2 10001 ^A 1) ACPI: FACP 30027AB3F0, 00F4 (r3 SGI FACPSN2 30001 ^A 1) ACPI: DSDT 3002518CC0, 002C (r1 SGI DSDTSN2 10001 ^A 1) ACPI: FACS 30027AB3A0, 0040 ACPI: DSDT 3002518CC0, 002C (r1 SGI DSDTSN2 10001 ^A 1) Number of logical nodes in system = 1 Number of memory chunks in system = 1 Entering add_active_range(0, 12585984, 12836864) 0 entries of 12800 used Entering add_active_range(0, 13631488, 13758464) 1 entries of 12800 used Entering add_active_range(0, 14680064, 14932815) 2 entries of 12800 used Entering add_active_range(0, 14932816, 14932840) 3 entries of 12800 used Entering add_active_range(0, 14933894, 14933896) 4 entries of 12800 used Entering add_active_range(0, 14933897, 14933919) 5 entries of 12800 used Entering add_active_range(0, 14933997, 14934015) 6 entries of 12800 used Initial ramdisk at: 0xe0000038f6504000 (8567062 bytes) SAL 2.9: SGI SN2 version 4.7 SAL Platform features: ITC_Drift SAL: AP wakeup using external interrupt vector 0x12 No logical to physical processor mapping available SAL_CAL_FLUSH failed with -1 ACPI: Local APIC address c0000000fee00000 ACPI: Error parsing MADT - no IOSAPIC entries register_intr: No IOSAPIC for GSI 52 2 CPUs available, 2 CPUs total Increasing MCA rendezvous timeout from 20000 to 49000 milliseconds MCA related initialization done ACPI: RSDP 3002518BE0, 0024 (r2 SGI) ACPI: XSDT 30027AB2B0, 004C (r1 SGI XSDTSN2 10001 ^A 1) ACPI: APIC 3002518C20, 0044 (r1 SGI APICSN2 10001 ^A 1) ACPI: SRAT 30027AB310, 0078 (r1 SGI SRATSN2 10001 ^A 1) ACPI: SLIT 3002518C80, 002D (r1 SGI SLITSN2 10001 ^A 1) ACPI: FACP 30027AB3F0, 00F4 (r3 SGI FACPSN2 30001 ^A 1) ACPI: DSDT 3002518CC0, 002C (r1 SGI DSDTSN2 10001 ^A 1) ACPI: FACS 30027AB3A0, 0040 ACPI: DSDT 3002518CC0, 002C (r1 SGI DSDTSN2 10001 ^A 1) SGI: Disabling VGA console SGI SAL version 4.07 Virtual mem_map starts at 0xa0007fffce200000 Zone PFN ranges: Normal 12585984 -> 14934016 early_node_map[7] active PFN ranges 0: 12585984 -> 12836864 0: 13631488 -> 13758464 0: 14680064 -> 14932815 0: 14932816 -> 14932840 0: 14933894 -> 14933896 0: 14933897 -> 14933919 0: 14933997 -> 14934015 On node 0 totalpages: 630673 Normal zone: 8025 pages used for memmap Normal zone: 0 pages reserved Normal zone: 622648 pages, LIFO batch:7 Built 1 zonelists. Total pages: 622648 Kernel command line: BOOT_IMAGE=scsi0:/EFI/debian/boot/vmlinuz-2.6.22-rc6 root=/dev/sda3 selinux=0 console=ttySG0,38400 ro PID hash table entries: 4096 (order: 12, 32768 bytes) CPU 0: base freq=200.000MHz, ITC ratio=13/2, ITC freq=1300.000MHz Console: colour dummy device 80x25 Memory: 10030432k/10074064k available (5101k code, 60336k reserved, 2587k data, 704k init) McKinley Errata 9 workaround not needed; disabling it Calibrating delay loop... 1945.60 BogoMIPS (lpj=3891200) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Dentry cache hash table entries: 2097152 (order: 10, 16777216 bytes) Inode-cache hash table entries: 1048576 (order: 9, 8388608 bytes) Mount-cache hash table entries: 1024 ACPI: Core revision 20070126 Boot processor id 0x0/0x0 CPU 1: base freq=200.000MHz, ITC ratio=13/2, ITC freq=1300.000MHz Brought up 2 CPUs Total of 2 processors activated (3891.20 BogoMIPS). migration_cost=7699 DMI not present or invalid. NET: Registered protocol family 16 ACPI DSDT OEM Rev 0x10001 PROM version < 4.50 -- implementing old PROM flush WAR ACPI: bus type pci registered ACPI: SCI (ACPI GSI 52) not registered ACPI: Interpreter enabled ACPI: Using IOSAPIC for interrupt routing Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 0 devices ACPI: ACPI bus type pnp unregistered NET: Registered protocol family 2 IP route cache hash table entries: 524288 (order: 8, 4194304 bytes) TCP established hash table entries: 2097152 (order: 11, 50331648 bytes) TCP bind hash table entries: 65536 (order: 6, 1048576 bytes) TCP: Hash tables configured (established 2097152 bind 65536) TCP reno registered checking if image is initramfs... it is Freeing initrd memory: 8352kB freed perfmon: version 2.0 IRQ 238 perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits) PAL Information Facility v0.5 perfmon: added sampling format default_format perfmon_default_smpl: default_format v2.0 registered audit: initializing netlink socket (disabled) audit(1182815529.364:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 2048 (order 0, 16384 bytes) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) EFI Time Services Driver v0.4 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled sn_console: Console driver init ttySG0 at I/O 0x0 (irq = 0) is a SGI SN L1 RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize mice: PS/2 mouse device common for all mice TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 704kB freed SCSI subsystem initialized Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. ACPI: Unable to derive IRQ for device 0000:02:02.0 ACPI: PCI Interrupt 0000:02:02.0[A]: no GSI tg3.c:v3.77 (May 31, 2007) ACPI: Unable to derive IRQ for device 0000:01:04.0 ACPI: PCI Interrupt 0000:01:04.0[A]: no GSI e1000: 0000:02:02.0: e1000_probe: (PCI:66MHz:64-bit) 00:04:23:ca:aa:da e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection PM: Writing back config space on device 0000:01:04.0 at offset b (was 164514e4, writing 801010a9) PM: Writing back config space on device 0000:01:04.0 at offset 3 (was 0, writing 3020) PM: Writing back config space on device 0000:01:04.0 at offset 2 (was 2000000, writing 2000015) PM: Writing back config space on device 0000:01:04.0 at offset 1 (was 2b00000, writing 2b00006) eth0: Tigon3 [partno(030-1771-000) rev 0105 PHY(5701)] (PCI:66MHz:64-bit) 10/100/1000Base-T Ethernet 08:00:69:13:f0:87 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[0] eth0: dma_rwctrl[76ff2d0f] dma_mask[64-bit] qla1280: QLA12160 found on PCI bus 1, dev 3 ACPI: Unable to derive IRQ for device 0000:01:03.0 ACPI: PCI Interrupt 0000:01:03.0[A]: no GSI scsi(0): Enabling SN2 PCI DMA dual channel lockup workaround scsi(0): Enabling SN2 PCI DMA workaround scsi(0:0): Resetting SCSI BUS scsi(0:1): Resetting SCSI BUS scsi0 : QLogic QLA12160 PCI to SCSI Host Adapter Firmware version: 10.04.42, Driver version 3.26 scsi 0:0:1:0: Direct-Access SEAGATE ST318453LC 0002 PQ: 0 ANSI: 3 scsi(0:0:1:0): Sync: period 9, offset 14, Wide, DT scsi 0:0:2:0: Direct-Access SGI ST318453LC 2741 PQ: 0 ANSI: 3 scsi(0:0:2:0): Sync: period 9, offset 14, Wide, DT qla1280: QLA12160 found on PCI bus 2, dev 1 ACPI: Unable to derive IRQ for device 0000:02:01.0 ACPI: PCI Interrupt 0000:02:01.0[A]: no GSI scsi(1): Enabling SN2 PCI DMA dual channel lockup workaround scsi(1): Enabling SN2 PCI DMA workaround scsi(1:0): Resetting SCSI BUS scsi(1:1): Resetting SCSI BUS scsi1 : QLogic QLA12160 PCI to SCSI Host Adapter Firmware version: 10.04.42, Driver version 3.26 sd 0:0:1:0: [sda] 35843686 512-byte hardware sectors (18352 MB) sd 0:0:1:0: [sda] Write Protect is off sd 0:0:1:0: [sda] Mode Sense: ab 00 10 08 sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sd 0:0:1:0: [sda] 35843686 512-byte hardware sectors (18352 MB) sd 0:0:1:0: [sda] Write Protect is off sd 0:0:1:0: [sda] Mode Sense: ab 00 10 08 sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA sda: sda1 sda2 sda3 sd 0:0:1:0: [sda] Attached SCSI disk sd 0:0:2:0: [sdb] 35843686 512-byte hardware sectors (18352 MB) sd 0:0:2:0: [sdb] Write Protect is off sd 0:0:2:0: [sdb] Mode Sense: ab 00 10 08 sd 0:0:2:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA sd 0:0:2:0: [sdb] 35843686 512-byte hardware sectors (18352 MB) sd 0:0:2:0: [sdb] Write Protect is off sd 0:0:2:0: [sdb] Mode Sense: ab 00 10 08 sd 0:0:2:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA sdb: sdb1 sdb2 sdb3 sd 0:0:2:0: [sdb] Attached SCSI disk md: linear personality registered for level -1 md: multipath personality registered for level -4 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid5: measuring checksumming speed ia64 : 3316.000 MB/sec raid5: using function: ia64 (3316.000 MB/sec) raid6: int64x1 1122 MB/s raid6: int64x2 1769 MB/s raid6: int64x4 2232 MB/s raid6: int64x8 2472 MB/s raid6: int64x16 3026 MB/s raid6: int64x32 1708 MB/s raid6: using algorithm int64x16 (3026 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 md: raid10 personality registered for level 10 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. ACPI: Unable to derive IRQ for device 0000:01:01.0 ACPI: PCI Interrupt 0000:01:01.0[A]: no GSI IOC4 0000:01:01.0: IO9 card detected. IOC4 0000:01:01.0: PCI clock is 15 ns. Adding 946144k swap on /dev/sda2. Priority:-1 extents:1 across:946144k EXT3 FS on sda3, internal journal device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com md: md1 stopped. md: md2 stopped. md: md3 stopped. PM: Writing back config space on device 0000:01:04.0 at offset b (was 164514e4, writing 801010a9) PM: Writing back config space on device 0000:01:04.0 at offset 3 (was 0, writing 3020) PM: Writing back config space on device 0000:01:04.0 at offset 2 (was 2000000, writing 2000015) PM: Writing back config space on device 0000:01:04.0 at offset 1 (was 2b00000, writing 2b00006)