orted. Intel machine check reporting enabled on CPU#0. CPU: AMD Mobile AMD Athlon(tm) 64 Processor 4000+ stepping 02 Checking 'hlt' instruction... OK. ACPI: Core revision 20060707 ACPI: setting ELCR to 0200 (from 0c80) NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on 0:18 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:14.4 PCI: Bus #04 (-#07) is hidden behind transparent bridge #03 (-#04) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB2_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs *10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *7 ACPI: PCI Interrupt Link [LNKC] (IRQs *10 11) ACPI: PCI Interrupt Link [LNKD] (IRQs 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs *10 11), disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs *10 11) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] Linux Plug and Play Support v0.97 (c) Adam Belay SCSI subsystem initialized libata version 2.00 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Bridge: 0000:00:02.0 IO window: 9000-9fff MEM window: c0000000-c00fffff PREFETCH window: c8000000-cfffffff PCI: Bridge: 0000:00:06.0 IO window: a000-afff MEM window: c0100000-c01fffff PREFETCH window: disabled. PCI: Bus 4, cardbus bridge: 0000:03:05.0 IO window: 0000b400-0000b4ff IO window: 0000b800-0000b8ff PREFETCH window: 50000000-53ffffff MEM window: 54000000-57ffffff PCI: Bridge: 0000:00:14.4 IO window: b000-bfff MEM window: c0200000-c02fffff PREFETCH window: 50000000-53ffffff PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:03:05.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 1445k freed apm: BIOS not found. highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NTFS driver 2.1.28 [Flags: R/O]. JFS: nTxBlock = 8055, nTxLock = 64440 SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:02.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie01] PCI: Setting latency timer of device 0000:00:06.0 to 64 assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie01] Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 aer_init: AER service init fails - Run ACPI _OSC fails aer: probe of 0000:00:02.0:pcie01 failed with error 2 Evaluate _OSC Set fails. Status = 0x0005 Evaluate _OSC Set fails. Status = 0x0005 aer_init: AER service init fails - Run ACPI _OSC fails aer: probe of 0000:00:06.0:pcie01 failed with error 2 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0xc8000000, mapped to 0xf8d00000, using 6144k, total 65536k vesafb: mode is 1024x768x16, linelength=2048, pages=41 vesafb: protected mode interface info at c000:5811 vesafb: pmi: set display start = c00c587f, set palette = c00c58b9 vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6>...no good signature found. Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device ACPI: AC Adapter [AC] (on-line) ACPI: Battery Slot [BAT0] (battery present) input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Power Button (CM) as /class/input/input1 ACPI: Power Button (CM) [PWRB] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SLPB] input: Lid Switch as /class/input/input3 ACPI: Lid Switch [LID] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ACPI: PCI Interrupt 0000:00:14.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt for device 0000:00:14.6 disabled floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4444K size 1024 blocksize loop: loaded (max 255 devices) Compaq SMART2 Driver (v 2.6.0) HP CISS Driver (v 3.6.14) input: Macintosh mouse button emulation as /class/input/input4 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10 PCI: setting IRQ 10 as level-triggered ACPI: PCI Interrupt 0000:00:14.1[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 ATIIXP: chipset revision 0 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: FUJITSU MHU2100AT, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-ST DVD-RW GCA-4080N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 hda8 > hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... Adaptec aacraid driver (1.1-5[2423]-mh3) scsi: Detection failed (no card) sym53c416.c: Version 1.0.0-ac qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.1.11 Copyright(c) 2004-2006 Emulex. All rights reserved. Failed initialization of WD-7000 SCSI card! DC390: clustering now enabled by default. If you get problems load with "disable_clustering=1" and report to maintainers spurious 8259A interrupt: IRQ7. megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006) megasas: 00.00.03.05 Mon Oct 02 11:21:32 PDT 2006 GDT-HA: Storage RAID Controller Driver. Version: 3.05 GDT-HA: Found 0 PCI Storage RAID Controllers 3ware Storage Controller device driver for Linux v1.26.02.002. 3ware 9000 Storage Controller device driver for Linux v2.26.02.008. nsp32: loading... st: Version 20061107, fixed bufsize 32768, s/g segs 256 I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Bus Adapter OSM v1.317 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 Fusion MPT base driver 3.04.03 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.03 Fusion MPT FC Host driver 3.04.03 Fusion MPT SAS Host driver 3.04.03 usbmon: debugfs is not available usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: No PS/2 controller found. Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 raid6: int32x1 1168 MB/s raid6: int32x2 1614 MB/s raid6: int32x4 823 MB/s raid6: int32x8 645 MB/s raid6: mmxx1 2167 MB/s raid6: mmxx2 4096 MB/s raid6: sse1x1 1806 MB/s raid6: sse1x2 3063 MB/s raid6: sse2x1 3074 MB/s raid6: sse2x2 4000 MB/s raid6: using algorithm sse2x2 (4000 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 7903.000 MB/sec raid5: using function: pIII_sse (7903.000 MB/sec) md: multipath personality registered for level -4 md: faulty personality registered for level -5 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com device-mapper: multipath: version 1.0.5 loaded device-mapper: multipath round-robin: version 1.0.0 loaded device-mapper: multipath emc: version 0.0.3 loaded TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode ACPI: (supports S0 S3 S4 S5) Time: tsc clocksource has been installed. Time: acpi_pm clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input5 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 296k freed squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher squashfs: LZMA suppport for slax.org by jro aufs 20070219 ISO 9660 Extensions: Microsoft Joliet Level 3 Unable to load NLS charset utf8 Unable to load NLS charset utf8 ISO 9660 Extensions: RRIP_1991A ISO 9660 Extensions: Microsoft Joliet Level 3 Unable to load NLS charset utf8 Unable to load NLS charset utf8 ISO 9660 Extensions: RRIP_1991A bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 87540 bytes,<6>...found (1024x768, 87432 bytes, v3). bootsplash: status on console 0 changed to on Adding 5325508k swap on /dev/hda6. Priority:-1 extents:1 across:5325508k input: PC Speaker as /class/input/input6 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:13.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 11, io mem 0xc0500000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 11, io mem 0xc0501000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ieee1394: Initialized config rom entry `ip1394' piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 ACPI: PCI Interrupt 0000:03:0e.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[c0203000-c02037ff] Max Packet=[2048] IR/IT contexts=[4/8] Yenta: CardBus bridge found at 0000:03:05.0 [107b:0506] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:03:05.0, mfunc 0x01001002, devctl 0x44 Yenta TI: socket 0000:03:05.0 probing PCI interrupt failed, trying to fix Linux agpgart interface v0.101 (c) Dave Jones Yenta TI: socket 0000:03:05.0 no PCI interrupts. Fish. Please report. Yenta: no PCI IRQ, CardBus support disabled for this socket. Yenta: check your BIOS CardBus, BIOS IRQ or ACPI settings. Yenta: ISA IRQ mask 0x00f8, PCI irq 0 Socket status: 30000020 Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07 pcmcia: parent PCI bridge I/O window: 0xb000 - 0xbfff cs: IO port probe 0xb000-0xbfff: clean. pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x53ffffff ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10 ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10 PCI: Setting latency timer of device 0000:02:00.0 to 64 sky2 v1.10 addr 0xc0100000 irq 10 Yukon-FE (0xb7) rev 1 sky2 eth0: addr 00:03:25:28:30:d2 ACPI: PCI Interrupt 0000:00:13.2[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:13.2: irq 11, io mem 0xc0502000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 8 ports detected cs: pcmcia_socket0: cardbus cards are not supported. ieee80211_crypt: registered algorithm 'NULL' ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation cs: IO port probe 0xc00-0xcff: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf cs: IO port probe 0x820-0x8ff: excluding 0x878-0x87f cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 cs: IO port probe 0x100-0x3af: excluding 0x200-0x20f cs: IO port probe 0xa00-0xaff: clean. bcm43xx driver ACPI: PCI Interrupt 0000:03:07.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt 0000:00:14.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 lp: driver loaded but no devices found input: ImPS/2 Synaptics TouchPad as /class/input/input7 fuse init (API version 7.8) Capability LSM initialized NTFS volume version 3.1. kjournald starting. Commit interval 5 seconds EXT3 FS on hda5, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda8, internal journal EXT3-fs: mounted filesystem with ordered data mode. sky2 eth0: enabling interface sky2 eth0: ram buffer 4K sky2 eth0: disabling interface cs: pcmcia_socket0: cardbus cards are not supported. cs: pcmcia_socket0: cardbus cards are not supported. 00:00.0 Host bridge: ATI Technologies Inc ATI Radeon Xpress 200 (RS480/RS482/RX480/RX482) Chipset - Host bridge (rev 01) > lspci 00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port 00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11) 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller ATI 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge 00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 02) 00:14.6 Modem: ATI Technologies Inc ATI SB400 - AC'97 Modem Controller (rev 02) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:00.0 VGA compatible controller: ATI Technologies Inc M24 1P [Radeon Mobility X600] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8036 PCI-E Fast Ethernet Controller (rev 10) 03:05.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01) 03:07.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) 03:0e.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) > lspcmcia socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:03:05.0) > uname -a Linux bt 2.6.20-BT-PwnSauce-NOSMP #3 Sat Feb 24 15:52:59 GMT 2007 i686 athlon-4 i386 GNU/Linux Let's try pclinuxos2007 on the same Gateway MX7515 Linux version 2.6.18.8.tex5 (vaughan@localhost) (gcc version 4.1.1 20060724 (prerelease) (4.1.1-4pclos2007)) #1 SMP Thu May 10 11:36:58 WST 2007 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009e000 (usable) BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000d2000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000003fe90000 (usable) BIOS-e820: 000000003fe90000 - 000000003fea4000 (ACPI data) BIOS-e820: 000000003fea4000 - 000000003ff00000 (ACPI NVS) BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved) BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) 126MB HIGHMEM available. 896MB LOWMEM available. found SMP MP-table at 000f8510 On node 0 totalpages: 261776 DMA zone: 4096 pages, LIFO batch:0 Normal zone: 225280 pages, LIFO batch:31 HighMem zone: 32400 pages, LIFO batch:7 DMI present. ACPI: RSDP (v000 PTLTD ) @ 0x000f84e0 ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x3fe9f0ce ACPI: FADT (v001 GATEWA W730-K8x 0x06040000 ATI 0x000f4240) @ 0x3fea3d9c ACPI: SSDT (v001 PTLTD POWERNOW 0x06040000 LTP 0x00000001) @ 0x3fea3e10 ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x3fea3f6a ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @ 0x3fea3fc4 ACPI: DSDT (v001 GATEWA W730-K8x 0x06040000 MSFT 0x0100000e) @ 0x00000000 ATI board detected. Disabling timer routing over 8254. ACPI: PM-Timer IO Port: 0x8008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 15:4 APIC version 16 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 33, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 21 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000) Detected 2586.858 MHz processor. Built 1 zonelists. Total pages: 261776 Kernel command line: BOOT_IMAGE=linux root=/dev/hda7 acpi=on resume=/dev/hda6 splash=silent vga=788 bootsplash: silent mode. mapped APIC to ffffd000 (fee00000) mapped IOAPIC to ffffc000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 PID hash table entries: 4096 (order: 12, 16384 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 1033364k/1047104k available (2078k kernel code, 13008k reserved, 662k data, 240k init, 129600k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay using timer specific routine.. 5178.72 BogoMIPS (lpj=10357443) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Mount-cache hash table entries: 512 CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 16k freed checking if image is initramfs... it is Freeing initrd memory: 635k freed ACPI: Core revision 20060707 ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. CPU0: AMD Mobile AMD Athlon(tm) 64 Processor 4000+ stepping 02 Total of 1 processors activated (5178.72 BogoMIPS). ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 ..MP-BIOS bug: 8254 timer not connected to IO-APIC ...trying to set up timer (IRQ0) through the 8259A ... failed. ...trying to set up timer as Virtual Wire IRQ... works. Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using MMCONFIG PCI: No mmconfig possible on 0:18 Setting up standard PCI resources ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 Boot video device is 0000:01:00.0 PCI: Transparent bridge - 0000:00:14.4 PCI: Bus #04 (-#07) is hidden behind transparent bridge #03 (-#04) (try 'pci=assign-busses') Please report the result to linux-kernel to fix this permanently ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB2_._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PB6_._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKB] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKD] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKE] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs 10 11) *0, disabled. ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2P_._PRT] ACPI: Embedded Controller [EC] (gpe 24) interrupt mode. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 10 devices PnPBIOS: Disabled PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:08: ioport range 0x1080-0x1080 has been reserved pnp: 00:08: ioport range 0x200-0x20f has been reserved pnp: 00:08: ioport range 0x87f-0x87f has been reserved pnp: 00:08: ioport range 0x220-0x22f has been reserved PCI: Bridge: 0000:00:02.0 IO window: 9000-9fff MEM window: c0000000-c00fffff PREFETCH window: c8000000-cfffffff PCI: Bridge: 0000:00:06.0 IO window: a000-afff MEM window: c0100000-c01fffff PREFETCH window: disabled. PCI: Bus 4, cardbus bridge: 0000:03:05.0 IO window: 0000b400-0000b4ff IO window: 0000b800-0000b8ff PREFETCH window: 50000000-51ffffff MEM window: 52000000-53ffffff PCI: Bridge: 0000:00:14.4 IO window: b000-bfff MEM window: c0200000-c02fffff PREFETCH window: 50000000-51ffffff PCI: Setting latency timer of device 0000:00:02.0 to 64 PCI: Setting latency timer of device 0000:00:06.0 to 64 ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 22 (level, low) -> IRQ 16 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered apm: BIOS not found. audit: initializing netlink socket (disabled) audit(1183489235.424:1): initialized highmem bounce pool size: 64 pages VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) PCI: Setting latency timer of device 0000:00:02.0 to 64 pcie_portdrv_probe->Dev[5a34:1002] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:02.0:pcie00] Allocate Port Service[0000:00:02.0:pcie01] PCI: Setting latency timer of device 0000:00:06.0 to 64 pcie_portdrv_probe->Dev[5a38:1002] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability Allocate Port Service[0000:00:06.0:pcie00] Allocate Port Service[0000:00:06.0:pcie01] vesafb: framebuffer at 0xc8000000, mapped to 0xf8880000, using 3750k, total 65536k vesafb: mode is 800x600x16, linelength=1600, pages=67 vesafb: protected mode interface info at c000:5811 vesafb: pmi: set display start = c00c587f, set palette = c00c58b9 vesafb: pmi: ports = 9010 9016 9054 9038 903c 905c 9000 9004 90b0 90b2 90b4 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 275007 bytes,<6>...found (800x600, 274959 bytes, v3). Console: switching to colour frame buffer device 93x31 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ATIIXP: IDE controller at PCI slot 0000:00:14.1 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 17 ATIIXP: chipset revision 0 ATIIXP: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x8410-0x8417, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x8418-0x841f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: FUJITSU MHU2100AT, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: HL-DT-ST DVD-RW GCA-4080N, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 195371568 sectors (100030 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100) hda: cache flushes supported hda: hda1 hda2 < hda5 hda6 hda7 hda8 > PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 NET: Registered protocol family 1 Using IPI No-Shortcut mode ACPI: (supports S0 S3 S4 S5) Freeing unused kernel memory: 240k freed Time: tsc clocksource has been installed. input: AT Translated Set 2 keyboard as /class/input/input0 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Synaptics Touchpad, model: 1, fw: 5.9, id: 0x23aeb3, caps: 0xa04713/0x10008 input: SynPS/2 Synaptics TouchPad as /class/input/input1 usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 19 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:13.0: irq 18, io mem 0xc0500000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.1[A] -> GSI 19 (level, low) -> IRQ 18 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.1: irq 18, io mem 0xc0501000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 4 ports detected ACPI: PCI Interrupt 0000:00:13.2[A] -> GSI 19 (level, low) -> IRQ 18 ehci_hcd 0000:00:13.2: EHCI Host Controller ehci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 3 ehci_hcd 0000:00:13.2: irq 18, io mem 0xc0502000 ehci_hcd 0000:00:13.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 8 ports detected ieee1394: Initialized config rom entry `ip1394' ACPI: PCI Interrupt 0000:03:0e.0[A] -> GSI 23 (level, low) -> IRQ 19 ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[c0203000-c02037ff] Max Packet=[2048] IR/IT contexts=[4/8] Capability LSM initialized Yenta: CardBus bridge found at 0000:03:05.0 [107b:0506] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:03:05.0, mfunc 0x01001002, devctl 0x44 ieee1394: Host added: ID:BUS[0-00:1023] GUID[0003252150007171] Yenta: ISA IRQ mask 0x0cf8, PCI irq 16 Socket status: 30000020 Yenta: Raising subordinate bus# of parent bus (#03) from #04 to #07 pcmcia: parent PCI bridge I/O window: 0xb000 - 0xbfff cs: IO port probe 0xb000-0xbfff: clean. pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff pcmcia: parent PCI bridge Memory window: 0x50000000 - 0x51ffffff pccard: CardBus card inserted into slot 0 yenta EnE: chaning testregister 0xC9, 04 -> 04 cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: excluding 0x408-0x40f 0x4d0-0x4d7 cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: excluding 0xc00-0xc07 0xc10-0xc17 0xc50-0xc57 0xc68-0xc6f 0xcd0-0xcdf cs: IO port probe 0xa00-0xaff: clean. ath_hal: module license 'Proprietary' taints kernel. ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413) wlan: 0.8.4.2 (0.9.3) ath_pci: 0.9.4.5 (0.9.3) PCI: Enabling device 0000:04:00.0 (0000 -> 0002) ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 22 (level, low) -> IRQ 16 ath_rate_sample: 1.2 (0.9.3) wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: turboG rates: 6Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps wifi0: H/W encryption support: WEP AES AES_CCM TKIP wifi0: mac 5.9 phy 4.3 radio 3.6 wifi0: Use hw queue 1 for WME_AC_BE traffic wifi0: Use hw queue 0 for WME_AC_BK traffic wifi0: Use hw queue 2 for WME_AC_VI traffic wifi0: Use hw queue 3 for WME_AC_VO traffic wifi0: Use hw queue 8 for CAB traffic wifi0: Use hw queue 9 for beacons wifi0: Atheros 5212: mem=0x52000000, irq=16 floppy0: no floppy controllers found Linux video capture interface: v2.00 bttv: driver version 0.9.16 loaded bttv: using 8 buffers with 2080k (520 pages) each for capture ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 20 ACPI: PCI interrupt for device 0000:00:14.6 disabled sdhci: Secure Digital Host Controller Interface driver, 0.12 sdhci: Copyright(c) Pierre Ossman martian loaded - 20061202 Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) powernow-k8: Found 1 Mobile AMD Athlon(tm) 64 Processor 4000+ processors (version 2.00.00) powernow-k8: 0 : fid 0x12 (2600 MHz), vid 0x8 powernow-k8: 1 : fid 0x10 (2400 MHz), vid 0xa powernow-k8: 2 : fid 0xe (2200 MHz), vid 0xc powernow-k8: 3 : fid 0xc (2000 MHz), vid 0xe powernow-k8: 4 : fid 0xa (1800 MHz), vid 0x10 powernow-k8: 5 : fid 0x8 (1600 MHz), vid 0x12 powernow-k8: 6 : fid 0x0 (800 MHz), vid 0x18 Time: acpi_pm clocksource has been installed. device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com loop: loaded (max 8 devices) EXT3 FS on hda7, internal journal Adding 5325508k swap on /dev/hda6. Priority:-1 extents:1 across:5325508k hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 bootsplash 3.1.6-2004/03/31: looking for picture...<6> silentjpeg size 275007 bytes,<6>...found (800x600, 274959 bytes, v3). bootsplash: status on console 0 changed to on ACPI: AC Adapter [AC] (on-line) Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8180 buckets, 65440 max) - 228 bytes per conntrack ACPI: Battery Slot [BAT0] (battery present) NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Sleep Button (CM) [SLPB] ACPI: Lid Switch [LID] Using specific hotkey driver Removing netfilter NETLINK layer. NET: Registered protocol family 17 ndiswrapper version 1.46 loaded (smp=yes) ndiswrapper: driver bcmwl5a (Broadcom,02/18/2005, 3.100.64.1) loaded ACPI: PCI Interrupt 0000:03:07.0[A] -> GSI 22 (level, low) -> IRQ 16 ndiswrapper: using IRQ 16 wlan0: ethernet device 00:14:a5:31:62:b6 using NDIS driver: bcmwl5a, version: 0x3644000, NDIS version: 0x501, vendor: '', 14E4:4318.5.conf wlan0: encryption modes supported: WEP; TKIP with WPA, WPA2, WPA2PSK; AES/CCMP with WPA, WPA2, WPA2PSK usbcore: registered new driver ndiswrapper ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 18 (level, low) -> IRQ 22 PCI: Setting latency timer of device 0000:02:00.0 to 64 sky2 v1.10 addr 0xc0100000 irq 22 Yukon-FE (0xb7) rev 1 sky2 eth0: addr 00:03:25:28:30:d2 sky2 eth1: enabling interface ADDRCONF(NETDEV_UP): eth1: link is not ready ADDRCONF(NETDEV_UP): wlan0: link is not ready Loading module: rt73usb - CVS (N/A) by http://rt2x00.serialmonkey.com. usbcore: registered new driver rt73usb Bluetooth: Core ver 2.10 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP ver 2.8 Bluetooth: L2CAP socket layer initialized ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 20 Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM ver 1.8 ip_tables: (C) 2000-2006 Netfilter Core Team ath0: no IPv6 routers present Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8180 buckets, 65440 max) - 228 bytes per conntrack [drm] Initialized drm 1.0.1 20051102 ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 22 [drm] Initialized radeon 1.25.0 20060524 on minor 0 ClusterIP Version 0.8 loaded successfully mtrr: 0xc8000000,0x8000000 overlaps existing 0xc8000000,0x4000000 mtrr: 0xc8000000,0x8000000 overlaps existing 0xc8000000,0x4000000 mtrr: 0xc8000000,0x8000000 overlaps existing 0xc8000000,0x4000000 Bridge firewalling registered [drm] Setting GART location based on new memory map [drm] Loading R300 Microcode [drm] writeback test succeeded in 1 usecs netfilter PSD loaded - (c) astaro AG IFWLOG: register target bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 3177 bytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 3177 bytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 3177 bytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 3177 bytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 3177 bytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 3177 bytes, v3). bootsplash: status on console 5 changed to on > lspci 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 200 (RS480/RS482/RX480/RX482) Chipset - Host bridge (rev 01) 00:02.0 PCI bridge: ATI Technologies Inc RS480 PCI-X Root Port 00:06.0 PCI bridge: ATI Technologies Inc RS480 PCI Bridge 00:13.0 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 00:13.1 USB Controller: ATI Technologies Inc IXP SB400 USB Host Controller 00:13.2 USB Controller: ATI Technologies Inc IXP SB400 USB2 Host Controller 00:14.0 SMBus: ATI Technologies Inc IXP SB400 SMBus Controller (rev 11) 00:14.1 IDE interface: ATI Technologies Inc Standard Dual Channel PCI IDE Controller 00:14.3 ISA bridge: ATI Technologies Inc IXP SB400 PCI-ISA Bridge 00:14.4 PCI bridge: ATI Technologies Inc IXP SB400 PCI-PCI Bridge 00:14.5 Multimedia audio controller: ATI Technologies Inc IXP SB400 AC'97 Audio Controller (rev 02) 00:14.6 Modem: ATI Technologies Inc SB400 AC'97 Modem Controller (rev 02) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:00.0 VGA compatible controller: ATI Technologies Inc M24 1P [Radeon Mobility X600] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8036 PCI-E Fast Ethernet Controller (rev 10) 03:05.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01) 03:07.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) 03:0e.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) 04:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01) > lspcmcia Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:03:05.0) CardBus card -- see "lspci" for more information > uname -a Linux localhost 2.6.18.8.tex5 #1 SMP Thu May 10 11:36:58 WST 2007 i686 Mobile AMD Athlon(tm) 64 Processor 4000+ GNU/Linux