<6>[ 16.520000] blueangel_pcmcia_configure_socket: Set Vcc to 0 V <6>[ 16.670000] blueangel_pcmcia_configure_socket: Set Vcc to 50 V <6>[ 17.090000] blueangel_pcmcia_configure_socket: Set Vcc to 50 V <6>[ 17.100000] blueangel_pcmcia_configure_socket: Set Vcc to 50 V <5>[ 17.220000] pccard: PCMCIA card inserted into slot 0 <5>[ 17.910000] pcmcia: registering new device pcmcia0.0 <4>[ 18.300000] acx: this driver is still EXPERIMENTAL <4>[ 18.300000] acx: reading README file and/or Craig's HOWTO is recommended, visit http://acx100.sf.net in case of further questions/discussion <4>[ 18.330000] acx: compiled to use 32bit I/O access. I/O timing issues might occur, such as non-working firmware upload. Report them <4>[ 18.350000] running on a little-endian CPU <4>[ 18.350000] PCI module v0.3.36 initialized, waiting for cards to probe... <6>[ 18.380000] acxcs_init() <6>[ 18.390000] acx_attach() <6>[ 18.400000] acx_cs_config(0xc7e72400) <6>[ 18.410000] MEMORY WINDOW FOUND!!! <6>[ 18.420000] requesting Irq... <4>[ 18.420000] pcmcia: request for exclusive IRQ could not be fulfilled. <4>[ 18.440000] pcmcia: the driver needs updating to supported shared IRQ lines. <6>[ 18.450000] blueangel_pcmcia_configure_socket: Set Vcc to 50 V <6>[ 18.470000] blueangel_pcmcia_configure_socket: Set Vcc to 50 V <6>[ 18.520000] RequestConfiguration OK <4>[ 18.530000] acx: found ACX100-based wireless network card <4>[ 18.540000] initial debug setting is 0x000A <6>[ 18.550000] memwinbase=2c000000 memwinsize=4096 <4>[ 18.560000] using IRQ 40 <4>[ 18.580000] ACX radio type 0x0d <4>[ 18.590000] requesting firmware image 'WLANGEN.BIN' <4>[ 19.140000] acx_write_fw (main): 0 <4>[ 19.290000] acx_validate_fw (main): 0 <4>[ 19.560000] requesting firmware image 'RADIO0d.BIN' <4>[ 19.630000] acx_write_fw (radio): 0 <4>[ 19.750000] acx_validate_fw (radio): 0 <4>[ 20.000000] acx100_s_init_wep: writing WEP options <4>[ 20.060000] initializing max packet templates <4>[ 20.360000] NVS_vendor_offs:0000 probe_delay:500 eof_memory:65536 <4>[ 20.370000] CCAModes:04 Diversity:01 ShortPreOpt:01 PBCC:01 ChanAgil:00 PHY:05 Temp:01 <4>[ 20.390000] AntennaID:01 Len:02 Data:1E 00 <4>[ 20.390000] PowerLevelID:0A Len:00 Data: <4>[ 20.400000] DataRatesID:02 Len:05 Data:02 04 11 22 44 <4>[ 20.410000] DomainID:03 Len:07 Data:30 20 30 31 32 40 41 <4>[ 20.410000] ProductID:04 Len:09 Data:TI ACX100 <4>[ 20.420000] ManufacturerID:05 Len:07 Data:TI Tes~ <4>[ 20.450000] acx: === chipset TNETW1100B, radio type 0x0D (Maxim), form factor 0x03 (Compact Flash), EEPROM version 0x05: uploaded firmware 'Rev 1.10.7.K' === <4>[ 20.470000] get_mask 0x00004D82, set_mask 0x00000000 <4>[ 20.490000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 20.500000] got sensitivity value 176 <4>[ 20.530000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 20.540000] got antenna value 0x8D <4>[ 20.570000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 20.580000] got Energy Detect (ED) threshold 112 <4>[ 20.610000] acx copy_from_slavemem: warning! destination not word-aligned! <4>[ 20.620000] got Channel Clear Assessment (CCA) value 13 <4>[ 20.650000] got regulatory domain 0x30 <4>[ 20.650000] get_mask 0x00000000, set_mask 0x00000000 - after update <4>[ 20.670000] new ratevector: 82 84 0B 16 2C <4>[ 20.670000] setting RXconfig to 2010:0FDD <4>[ 20.700000] creating /proc entry driver/acx_wlan0 <4>[ 20.700000] creating /proc entry driver/acx_wlan0_diag <4>[ 20.710000] creating /proc entry driver/acx_wlan0_eeprom <4>[ 20.720000] creating /proc entry driver/acx_wlan0_phy <4>[ 20.730000] acx v0.3.36: net device wlan0, driver compiled against wireless extensions 22 and Linux 2.6.21-hh10 root@htcblueangel:~$ pccardctl ls Socket 0 Bridge: [pxa2xx-pcmcia] (bus ID: pxa2xx-pcmcia.0) Socket 0 Device 0: [acx_cs] (bus ID: 0.0) root@htcblueangel:~$ pccardctl info PRODID_1="Texas Instruments" PRODID_2="ACX100" PRODID_3="" PRODID_4="" MANFID=0097,8402 FUNCID=6 root@htcblueangel:~$ pccardctl status Socket 0: 5.0V 16-bit PC Card Subdevice 0 (function 0) bound to driver "acx_cs" root@htcblueangel:~$ pccardctl ident Socket 0: product info: "Texas Instruments", "ACX100", "", "" manfid: 0x0097, 0x8402 function: 6 (network)