>printenv
HWRevision            93
ProductID             Fritz_Box_SpeedportW501V
SerialNumber          0000000000000000
annex                 B
autoload              yes
bootloaderVersion     1.123
bootserport           tty0
bluetooth             00:04:0E:FF:FF:07
cpufrequency          211968000
firstfreeaddress      0x946AD100
firmware_version      tcom
firmware_info         28.04.38
flashsize             0x00400000
maca                  00:00:00:00:00:00
macb                  00:00:00:00:00:00
macwlan               00:00:00:00:00:00
macdsl                00:00:00:00:00:00
memsize               0x01000000
modetty0              38400,n,8,1,hw
modetty1              38400,n,8,1,hw
mtd0                  0x90000000,0x90000000
mtd1                  0x90010000,0x903C0000
mtd2                  0x90000000,0x90010000
mtd3                  0x903C0000,0x903E0000
mtd4                  0x903E0000,0x90400000
my_ipaddress          192.168.178.1
prompt                AVM_Ar7
ptest                 
reserved              00:04:0E:FF:FF:00
req_fullrate_freq     125000000
sysfrequency          125000000
urlader-version       1123
usb_board_mac         00:00:00:00:00:00
usb_rndis_mac         00:00:00:00:00:00
usb_device_id         0x5401
usb_revision_id       0x0200
usb_device_name       USB DSL Device
usb_manufacturer_name  AVM


 >go
AVM decompress Kernel:
.................done
start kernel
[ohio_pre_init] System Clk = 62500000 Hz               

LINUX started...
Linux version 2.6.13.1-ohio (686) (gcc version 3.4.6) #9 Wed Apr 4 13:48:08 CEST 2007
memsize=16 MByte
flashsize=4 MByte
&_end=0x942096e8 PFN_ALIGN(&_end)=0x9420a000 CPHYSADDR(PFN_ALIGN(&_end))=0x1420a000 memsize=0x1000
CPU revision is: 00018448
[ohio_gpio_init]
Determined physical RAM map:
 memory: 0020a000 @ 14000000 (reserved)
 memory: 00df6000 @ 1420a000 (usable)
On node 0 totalpages: 4096
[alloc_node_mem_map] reduce size from 2752544 Bytes to  131104 Bytes
[alloc_node_mem_map]: (org) sizeof(mem_map) = 131104 mem_map=0x9420d000-0x9422d020
[alloc_node_mem_map]: sizeof(mem_map) = 2752544 mem_map=0x93f8d000-0x9422d020
zone=0 zone_size[j]=0x86016
realsize=4096
  DMA zone: 4096 pages, LIFO batch:1
zone=1 zone_size[j]=0x0
realsize=0
  Normal zone: 0 pages, LIFO batch:1
zone=2 zone_size[j]=0x0
realsize=0
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line:  console=ttyS0,38400n8r
[ld_mmu_r4xx0] memcpy((void *)(CAC_BASE   + 0x100), &except_vec2_generic, 0x30)
Primary instruction cache 16kB, physically tagged, 4-way, linesize 16 bytes.
Primary data cache 8kB, 4-way, linesize 16 bytes.
Synthesized TLB refill handler (20 instructions). Base=0x941df63c
TLB synthesizer field overflow (simm)
Synthesized TLB load handler fastpath (34 instructions) Base=0x941e2620.
TLB synthesizer field overflow (simm)
Synthesized TLB store handler fastpath (34 instructions) Base=0x941e2820.
TLB synthesizer field overflow (simm)
Synthesized TLB modify handler fastpath (33 instructions) Base=0x941e2a20.
PID hash table entries: 128 (order: 7, 2048 bytes)
CPU frequency 211.97 MHz
Using 105.984 MHz high precision timer.
[setup_irq]: irq 127 irqaction->handler 0x94042530 (no_action+0x0/0x8 )
[register_console] enable commandline console 0
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 14116k/14296k available (1468k kernel code, 164k reserved, 340k data, 112k init, 0k highm)
totalram_pages= 3533
Calibrating delay loop... 211.35 BogoMIPS (lpj=1056768)
loops_per_jiffy=1056768
Mount-cache hash table entries: 512
Checking for 'wait' instruction...  available.
NET: Registered protocol family 16
Can't analyze prologue code at 9416d748
Squashfs 2.2-r2b (released 2006/02/23) (C) 2002-2005 Phillip Lougher
[avm_power]Ohio250 detected -> overclocking possible
[avm] configured: watchdog eventled enable direct gpio 

AR7WDT: Watchdog Driver for AR7 Hardware (Version 1.0, build: Apr  4 2007 13:46:17)
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
[uart_add_one_port]
ttyS0 at MMIO 0x0 (irq = 15) is a OHIO_UART
[uart_add_one_port] dont register console port->type = 16
port->cons = 0x941a7450 port->cons->flags = 0x7
[uart_add_one_port] success
io scheduler noop registered
[cpmac] cpmac_if_register, dev eth0 (phy_id 0) registered
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
physmap flash device: 400000 at 10000000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 16-bit bank
[genprobe_ident_chips] 4 i 0 j 0
[genprobe_ident_chips] 5 i 0 j 1
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
RedBoot partition parsing not available
Generic platform RAM MTD, (c) 2004 Simtec Electronics
Ohio flash driver (size->0x400000 mem->0x10000000)
flash_size=0x400000
flash_mask=0x7fffff
Ohio flash memory: Found 1 x16 devices at 0x0 in 16-bit bank
[genprobe_ident_chips] 4 i 0 j 0
[genprobe_ident_chips] 5 i 0 j 1
 Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
[mtd]: set to default: jffs2_size = 0x20 * 64KByte (0x200000 Bytes)
[ohio_find_hidden_filesystem]: super block found: bytes_used: 0x305de3/3169763
[init_ohio_flash] find hidden filesystem size=0x314300 offset=0xabd00
[mtd] configure jffs2 partition
[mtd] fs_size=0x3b0000 max=0x0 is=0x200000 max jffs2_size value 0
[mtd] ERROR jffs2_size too big, reduce to max
[mtd] ohio_flash_map: name=Ohio flash memory bankwidth=2 virt=0xb0000000 phys=0x10000000 size=0x40
Creating 5 MTD partitions on "Ohio flash memory":
0x000abd00-0x003c0000 : "filesystem"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
mtd: partition "filesystem" doesn't start on an erase block boundary -- force read-only
0x00010000-0x003c0000 : "kernel"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x00000000-0x00010000 : "bootloader"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x003c0000-0x003e0000 : "tffs (1)"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
0x003e0000-0x00400000 : "tffs (2)"
        'nor-flash'
        'Bits can be cleared (flash)'
        'Has an erase function'
partition_info[0]: name=filesystem offset=abd00 size=314300
partition_info[0]: 0xb00abd00: 0x73717368 0x56d
partition_info[1]: name=kernel offset=10000 size=3b0000
partition_info[1]: 0xb0010000: 0xfeed1281 0x9bc03
partition_info[2]: name=bootloader offset=0 size=10000
partition_info[2]: 0xb0000000: 0x40809000 0x40809800
partition_info[3]: name=tffs (1) offset=3c0000 size=20000
partition_info[3]: 0xb03c0000: 0x40001 0x95ffffff
partition_info[4]: name=tffs (2) offset=3e0000 size=20000
partition_info[4]: 0xb03e0000: 0x40001 0x94ffffff
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
[setup_irq]: irq 1 irqaction->handler 0x94001390 (dummy_timer_irq+0x0/0x14 )
[setup_irq]: irq 6 irqaction->handler 0x940013a4 (dummy_system_irq_2+0x0/0x14 )
[ohio_late_init] 
TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 2.0)
      mount on mtd4 and mtd5 (double buffering)
Adam2 environment variables API installed.
[prepare_namespace] new mount root /dev/mtdblock1
use lzma compression 
VFS: Mounted root (squashfs filesystem) readonly.
Freeing prom memory: 0kb freed
Freeing unused kernel memory: 112k freed (3561 free)
[setup_irq]: irq 15 irqaction->handler 0x940cf170 (serial8250_interrupt+0x0/0x13c )
[avm_led] from virt led ('festnetz', 2) not registered
[avm_led] format error: "MAP Name,Instanz TO Name,Instanz"
[avm_led_load_config] Syntax error in led config file /etc/led.conf at "MAP festnetz,2 TO nu"
init started: BusyBox v1.5.1 (2007-06-26 06:27:13 CEST) multi-call binary
starting pid 16, tty '': '/etc/init.d/rc.S'
rootdir=/
table='/etc/device.table'
AR7WDT: System Init UEberwachung 120 Sekunden
TFFS Name Table 9
Jan  1 00:00:04 ar7cfgctl[70]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 00:00:04 ar7cfgctl[70]: load_config(ar7): factory default loaded
HWRevision      93
ProductID       Fritz_Box_SpeedportW501V
SerialNumber    0000000000000000
annex   B
autoload        yes
bootloaderVersion       1.123
bootserport     tty0
bluetooth       00:04:0E:FF:FF:07
cpufrequency    211968000
firstfreeaddress        0x946AD100
firmware_version        tcom
firmware_info   28.04.38
flashsize       0x00400000
maca    00:00:00:00:00:00
macb    00:00:00:00:00:00
macwlan 00:00:00:00:00:00
macdsl  00:00:00:00:00:00
memsize 0x01000000
modetty0        38400,n,8,1,hw
modetty1        38400,n,8,1,hw
mtd0    0x90000000,0x90000000
mtd1    0x90010000,0x903C0000
mtd2    0x90000000,0x90010000
mtd3    0x903C0000,0x903E0000
mtd4    0x903E0000,0x90400000
my_ipaddress    192.168.178.1
prompt  AVM_Ar7
ptest
reserved        00:04:0E:FF:FF:00
req_fullrate_freq       125000000
sysfrequency    125000000
urlader-version 1123
usb_board_mac   00:00:00:00:00:00
usb_rndis_mac   00:00:00:00:00:00
usb_device_id   0x5401
usb_revision_id 0x0200
usb_device_name USB DSL Device
usb_manufacturer_name   AVM
wlan_cal        03EC,0011,0012,00EC,010A,00F7,010A,02EF,0308
Jan  1 01:00:06 ar7cfgctl[118]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:06 ar7cfgctl[118]: load_config(ar7): factory default loaded
HWRevision='93'
HWRevision_ATA='1'
HWRevision_BitFileCount=''
HWRevision_Reserved1='0'
ANNEX='B'
OEM='tcom'
OEM_DEFAULT_INDEX=''
OEM_tmp='tcom'
Language='de'
Country='049'
TZ='CET-1CEST-2,M3.5.0/02:00:00,M10.5.0/03:00:00'
CONFIG_AB_COUNT='2'
CONFIG_ACCESSORY_URL='http://www.avm.de/fritzbox_apps.php?hardware=93&oem=tcom&language=de&countr'
CONFIG_ANNEX='B'
CONFIG_ASSIST='y'
CONFIG_ATA='y'
CONFIG_ATA_FULL='n'
CONFIG_AUDIO='n'
CONFIG_AURA='n'
CONFIG_BLUETOOTH='n'
CONFIG_BLUETOOTH_CTP='n'
CONFIG_BUTTON='n'
CONFIG_CAPI='y'
CONFIG_CAPI_MIPS='n'
CONFIG_CAPI_NT='n'
CONFIG_CAPI_POTS='y'
CONFIG_CAPI_TE='n'
CONFIG_CAPI_UBIK='n'
CONFIG_CAPI_XILINX='y'
CONFIG_CDROM='n'
CONFIG_CDROM_FALLBACK='n'
CONFIG_DECT='n'
CONFIG_DSL='y'
CONFIG_ECO='n'
CONFIG_ENVIRONMENT='/var/env'
CONFIG_ENVIRONMENT_PATH='/proc/sys/urlader'
CONFIG_ETH_COUNT='1'
CONFIG_FIRMWARE_URL='http://www.t-com.de/downloads'
CONFIG_FON='y'
CONFIG_FONGUI2='n'
CONFIG_FONQUALITY='y'
CONFIG_HOMEI2C='n'
CONFIG_HOSTNAME='speedport.ip'
CONFIG_I2C='n'
CONFIG_INSTALL_TYPE='ar7_4MB_1eth_2ab_pots_wlan_28776'
CONFIG_IPONE='n'
CONFIG_JFFS2='n'
CONFIG_KIDS='n'
CONFIG_LED_NO_DSL_LED='n'
CONFIG_MAILER='n'
CONFIG_MEDIACLI='n'
CONFIG_MEDIASRV='n'
CONFIG_NAND='n'
CONFIG_NFS='n'
CONFIG_OEM_DEFAULT='tcom'
CONFIG_PRODUKT='Fritz_Box_SpeedportW501V'
CONFIG_PRODUKT_NAME='Speedport W 501V'
CONFIG_RAMSIZE='16'
CONFIG_RELEASE='1'
CONFIG_ROMSIZE='4'
CONFIG_SAMBA='n'
CONFIG_SERVICEPORTAL_URL='none'
CONFIG_STOREUSRCFG='y'
CONFIG_SUBVERSION='ds26-pre16-870M'
CONFIG_SWAP='n'
CONFIG_TAM='n'
CONFIG_TAM_MODE='0'
CONFIG_TR064='n'
CONFIG_TR069='y'
CONFIG_UBIK2='n'
CONFIG_UPNP='n'
CONFIG_USB='n'
CONFIG_USB_HOST_AVM='n'
CONFIG_USB_HOST_TI='n'
CONFIG_USB_PRINT_SERV='n'
CONFIG_USB_STORAGE='n'
CONFIG_USB_WLAN_AUTH='n'
CONFIG_VDSL='n'
CONFIG_VERSION='04.38'
CONFIG_VERSION_MAJOR='28'
CONFIG_VLYNQ='y'
CONFIG_VLYNQ0='3'
CONFIG_VLYNQ1='0'
CONFIG_VLYNQ_PARAMS='vlynq_reset_bit_0=17'
CONFIG_VPN='n'
CONFIG_WLAN='y'
CONFIG_WLAN_1130TNET='n'
CONFIG_WLAN_1350TNET='y'
CONFIG_WLAN_GREEN='n'
CONFIG_WLAN_IPTV='n'
CONFIG_WLAN_TXPOWER='n'
CONFIG_WLAN_WDS='y'
CONFIG_WLAN_WMM='n'
CONFIG_XILINX='y'
set 'Activate Wizzard'
mknod: /var/flash/ar7.cfg: File exists
Loading /var/flash/ds_mod...done.
Loading passwords...done.
Loading hosts...Jan  1 01:00:08 ar7cfgctl[186]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:08 ar7cfgctl[186]: load_config(ar7): factory default loaded
Jan  1 01:00:08 ar7cfgctl[189]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:08 ar7cfgctl[189]: load_config(ar7): factory default loaded
Jan  1 01:00:08 ar7cfgctl[192]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:08 ar7cfgctl[192]: load_config(ar7): factory default loaded
Jan  1 01:00:08 ar7cfgctl[195]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:08 ar7cfgctl[195]: load_config(ar7): factory default loaded
Jan  1 01:00:08 ar7cfgctl[199]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:09 ar7cfgctl[199]: load_config(ar7): factory default loaded
done.
Loading config...done.
Loading modules...done.
checkempty: : No such file or directory
checkempty: : No such file or directory
checkempty: warning, /var/flash/ar7.cfg not found - nop
checkempty: : No such file or directory
checkempty: warning, /var/flash/voip.cfg not found - nop
Piglet: module license '
(C) Copyright 2005 by AVM
' taints kernel.
EMIF: asize=0 ta=3 r_hold=0 w_strobe=6 r_strobe=6 ew=1
attempting to load DSL Firmware '/lib/modules/microvoip-dsl.bin'
**** ANNEX: 'B'
*************************************
setting DSL Firmware to Annex B
registered device TI Avalanche SAR
tiatm driver (patch_annex=0xc0053e2c)
[tiatm] Set StrictPriority=0
DSP binary filesize = 298788 bytes
[tiatm] INFO V2U-BRIDGEREGISTER: 0x00000019
[setup_irq]: irq 23 irqaction->handler 0xc003b208 (tn7atm_sar_irq+0x0/0x30 [tiatm] )
[setup_irq]: irq 31 irqaction->handler 0xc003b238 (tn7atm_dsl_irq+0x0/0x28 [tiatm] )
[tiatm]: Powermanagment (States => 1,3,10) supported!
Texas Instruments ATM driver: version:[4.06.04.41]
ubik2 driver (ubik2 - 0x10=0xc0067a74)
atm_dsp_register_ubik2: ubik2_ToMIPS_notify=0xc0057bfc
atm_dsp_register_ubik2: dsp mem pointer 0xa1c0e0c4
ubik2_init_interface: DSP-Link Version v3 8180
driver params overwritten io_addr=0x0 irq_num=0
[4294938555]DSP-Fw: Version 2.188] EC=3 DTMF=3 Slots=3 BChan=3(Analog=3) DChan=0 Fifo=128
Jan  1 01:00:14 ar7cfgctl[251]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:14 ar7cfgctl[251]: load_config(ar7): factory default loaded
kdsldmod: init start (Apr 18 2007 14:44:44) sizeof(struct sk_buff)=160
kdsldmod: init done
<6>kdsld: PPP led: off (value=0)
Jan  1 01:00:17 ctlmgr[282]: process priority is 19
MAC WLAN:       00:00:00:00:00:00
Jan  1 01:00:19 ctlmgr[284]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:19 ctlmgr[284]: load_config(ar7): factory default loaded
Jan  1 01:00:19 ctlmgr[284]: FactoryDefault=/etc/default/tcom/voip.cfg (voip)
Jan  1 01:00:19 ctlmgr[284]: load_config(voip): factory default loaded
Jan  1 01:00:19 ctlmgr[284]: dlopen(/usr/share/ctlmgr/libdect.so) failed: File not found
Jan  1 01:00:19 ctlmgr[284]: dlopen(/usr/share/ctlmgr/libtamconf.so) failed: File not found
Jan  1 01:00:19 ctlmgr[284]: dlopen(/usr/share/ctlmgr/libuser.so) failed: File not found
Jan  1 01:00:19 ctlmgr[284]: mapping to info-LED already exist
Jan  1 01:00:19 ctlmgr[284]: box init ok
Jan  1 01:00:19 ctlmgr[284]: /dev/avm_power <-- MODE=dsl
Jan  1 01:00:19 ctlmgr[284]: WAN (ata) led value = 0
Jan  1 01:00:20 ctlmgr[284]: TR069_Init() TR069_Init(assi-only)
Jan  1 01:00:20 ctlmgr[284]: TR069_Init returned 0
Jan  1 01:00:20 ctlmgr[284]: TR069_Init() returned 0
Jan  1 01:00:20 ctlmgr[284]: verbose: DISABLED
WSTART (Apr  4 2007 13:51:02)Wstart - no WEP/WPA key set - no WLAN encryption
libwlanparam: config ok(1)
wpa auth:waiting for driver to come up...
Wstart - made configure_wpa_authenticator

[Wstart] wlan_cal ist gesetzt: NVS DATEI WIRD MIT KALIBRIERUNGSWERTEN GEPATCHT!!!
 [Wstart] 9 Parameter werden gepatcht:
[Wstart] NVS DATEI WURDE GEPATCHT.

NVS File loaded.
[ohio_vlynq_init] device 0
[ohio_vlynq_startup_link] 
[setup_irq]: irq 29 irqaction->handler 0x9400554C (vlynq_interrupt+0x0/0x34 )
[setup_irq]: irq 79 irqaction->handler 0xC019714C (tiwlan_ddaSrand+0x8/0x30 [tiap] )
[4294939554]DSP: XDU=0 OVR=0 MIPS_OVR=1
tiwlan_dda_get_netif_ipaddr: Failed to get net device struct for br0
wlan started (OK)
Wstart - made configure_and_start_ap_driver
WSTART: done(0)
WLAN is enabled
tiwlan0 device is activated
wdsup0 device is activated
wdsdw0 device is activated
wdsdw1 device is activated
wdsdw2 device is activated
wdsdw3 device is activated
Jan  1 01:00:26 websrv[303]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:26 websrv[303]: load_config(ar7): factory default loaded
Jan  1 01:00:27 websrv[303]: startup (Apr 18 2007 14:42:12)
Jan  1 01:00:27 multid[313]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:27 multid[313]: load_config(ar7): factory default loaded
Jan  1 01:00:28 multid[313]: startup (May 10 2007 13:17:12)
Jan  1 01:00:28 dsld[317]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:28 dsld[317]: load_config(ar7): factory default loaded
Jan  1 01:00:28 dsld[317]: startup (Apr 18 2007 14:43:23)
Jan  1 01:00:28 dsld[319]: DSL 00:00:00:00:00:00
Jan  1 01:00:28 dsld[319]: VOIP Mac 00:00:00:00:00:00
Jan  1 01:00:28 dsld[319]: VCC2 Mac 00:00:00:00:00:00
Jan  1 01:00:28 dsld[319]: VCC3 Mac 00:00:00:00:00:00
Jan  1 01:00:28 dsld[319]: voip: ppptarget voip disabled, ignored
Jan  1 01:00:28 dsld[319]: compiled tc filter  to 0 classes
Jan  1 01:00:28 dsld[319]: compiled tc filter tc:rtp,sip to 2 classes
Jan  1 01:00:28 dsld[319]: compiled tc filter tc:tcp_ack to 1 classes
Jan  1 01:00:28 dsld[319]: compiled tc filter tc:dns,sipdns,ntpdns,tr069dns to 4 classes
Jan  1 01:00:28 dsld[319]: compiled tc filter tc:http_req,tr069 to 2 classes
Jan  1 01:00:28 dsld[319]: compiled tc filter tc:icmp to 1 classes
Jan  1 01:00:28 dsld[319]: compiled tc filter  to 0 classes
Jan  1 01:00:28 dsld[319]: verbose: DISABLED
<6>kdsld: sync lost
[cpmac] cpmac_main_ioctl, unknown ioctl 35142
device eth0 entered promiscuous mode
[setup_irq]: irq 27 irqaction->handler 0x940DF8BC (cpmac_main_isr+0x0/0x78 )
tiwlan_ddaDoIoctl : Unknown ioctl 35142
device tiwlan0 entered promiscuous mode
lan: port 2(tiwlan0) entering learning state
lan: topology change detected, propagating
lan: port 2(tiwlan0) entering forwarding state
tiwlan_ddaWdsDoIoctl : Unknown ioctl 35142
device wdsup0 entered promiscuous mode
lan: port 3(wdsup0) entering learning state
tiwlan_ddaWdsDoIoctl : Unknown ioctl 35142
device wdsdw0 entered promiscuous mode
lan: port 4(wdsdw0) entering learning state
tiwlan_ddaWdsDoIoctl : Unknown ioctl 35142
device wdsdw1 entered promiscuous mode
lan: port 5(wdsdw1) entering learning state
lan: topology change detected, propagating
lan: port 3(wdsup0) entering forwarding state
lan: topology change detected, propagating
lan: port 4(wdsdw0) entering forwarding state
lan: topology change detected, propagating
lan: port 5(wdsdw1) entering forwarding state
tiwlan_ddaWdsDoIoctl : Unknown ioctl 35142
device wdsdw2 entered promiscuous mode
lan: port 6(wdsdw2) entering learning state
tiwlan_ddaWdsDoIoctl : Unknown ioctl 35142
device wdsdw3 entered promiscuous mode
lan: port 7(wdsdw3) entering learning state
lan: topology change detected, propagating
lan: port 6(wdsdw2) entering forwarding state
lan: topology change detected, propagating
lan: port 7(wdsdw3) entering forwarding state
Jan  1 01:00:29 multid[315]: 01:00:28(1) [Segmentation fault] multid(315) CRASHED at 2ad7ebfc (/l)
Jan  1 01:00:29 multid[315]: [bt] Number of functions: (0)
telefon: use clock_gettime(CLOCK_MONOTONIC)!
telefon: SIGCHLD received!
telefon: WARNING No MOH file '/var/flash/fx_moh' !
telefon: WARNING No MOH file '/var/fx_moh' !
telefon: WARNING No MOH file '/etc/default/fx_moh' !
Jan  1 01:00:31 voipd[331]: FactoryDefault=/etc/default/tcom/voip.cfg (voip)
Jan  1 01:00:31 voipd[331]: load_config(voip): factory default loaded
Jan  1 01:00:31 voipd[331]: startup (AVM Speedport W 501V 28.04.38 AVM SIP v7.01.07 Apr 18 2007 1)
Jan  1 01:00:31 voipd[331]: using capi controller 5
Jan  1 01:00:31 voipd[331]: using b1 protocol 10 for 8kHz
Jan  1 01:00:31 voipd[331]: tel: NOT supported
Jan  1 01:00:31 voipd[331]: ENUM NOT supported
Jan  1 01:00:31 voipd[331]: Couldn't load shared library libspeex.so - File not found - Not a dir)
Jan  1 01:00:31 voipd[331]: VoIP led value = 0
Jan  1 01:00:31 voipd[331]: no useragent configured
Jan  1 01:00:31 voipd[331]: INFO led: off (value=0)
Jan  1 01:00:31 voipd[331]: VoIP SRTP led value = 0
Jan  1 01:00:31 voipd[331]: priority is -20
Jan  1 01:00:31 voipd[331]: encaplen 32
Jan  1 01:00:31 voipd[331]: brutto speed unknown
Jan  1 01:00:31 voipd[331]: connstatus 0 -> 3
Jan  1 01:00:31 voipd[331]: PCMA/8000/1: 98933 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: PCMU/8000/1: 98933 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: G726-32/8000/1: 70666 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: G726-40/8000/1: 70666 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: G726-24/8000/1: 56533 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: PCMA/16000/1: 169600 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: PCMU/16000/1: 169600 bits/second (encaplen=32,30ms)
Jan  1 01:00:31 voipd[331]: PCMA/8000/1: 106000 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: PCMU/8000/1: 106000 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: G726-32/8000/1: 84800 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: G726-40/8000/1: 84800 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: G726-24/8000/1: 63600 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: PCMA/16000/1: 190800 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: PCMU/16000/1: 190800 bits/second (encaplen=32,20ms)
Jan  1 01:00:31 voipd[331]: verbose: DISABLED
/etc/init.d/rc.voip: line 98: pbd: not found
Jan  1 01:00:32 ar7cfgctl[335]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:32 ar7cfgctl[335]: load_config(ar7): factory default loaded
run_clock demon started

AR7WDT: System Init UEberwachung abgeschlossen (89810 ms noch verfuegbar)
/etc/init.d/rc.S: line 492: cannot create /proc/sysrq-trigger: nonexistent directory
Jan  1 01:00:36 igdd[307]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:36 igdd[307]: load_config(ar7): factory default loaded
Jan  1 01:00:36 igdd[307]: OemStringData.MAC:00150C45F5AF
Jan  1 01:00:36 igdd[307]: OemStringData.BOXID='Speedport W 501V', _boxenv_name_and_version='AVM '
Jan  1 01:00:36 igdd[307]: desc=Speedport W 501V UPnP/1.0 AVM Speedport W 501V 28.04.38
Jan  1 01:00:36 igdd[307]: startup (May  8 2007 19:44:45)
Jan  1 01:00:36 igdd[307]: verbose: DISABLED
rc.mod version ds26-pre16-870M
crond is disabled
telnetd is disabled
Starting webinterface...done.
Starting ssh server...done.
inadyn is disabled

Please press Enter to activate this console. 
starting pid 415, tty '/dev/ttyS0': '/bin/sh'


BusyBox v1.5.1 (2007-06-26 06:27:13 CEST) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

Jan  1 01:00:58 ar7cfgctl[457]: FactoryDefault=/etc/default/tcom/ar7.cfg (ar7)
Jan  1 01:00:58 ar7cfgctl[457]: load_config(ar7): factory default loaded
ermittle die aktuelle TTY
tty is "/dev/ttyS0"
Serielles Terminal