LSPCI 00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03) 00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03) 00:04.0 CardBus bridge: Texas Instruments PCI1211 00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02) 00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01) 00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01) 00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03) 00:08.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12) 00:09.0 Ethernet controller: Intel Corporation 82557/8/9 Ethernet Pro 100 (rev 09) 00:09.1 Serial controller: Agere Systems LT WinModem 01:00.0 VGA compatible controller: ATI Technologies Inc Rage Mobility P/M AGP 2x (rev 64) DMESG : PCI Interrupt Routing Table [\_SB_.C03A.C03B._PRT] ACPI: PCI Interrupt Link [C090] (IRQs 5 10 *11) ACPI: PCI Interrupt Link [C091] (IRQs 11) *0, disabled. ACPI: PCI Interrupt Link [C092] (IRQs 5 10 *11) ACPI: PCI Interrupt Link [C093] (IRQs 5 10 *11) ACPI: Power Resource [C11E] (on) ACPI: Power Resource [C132] (on) ACPI: Power Resource [C13A] (on) ACPI: Power Resource [C146] (on) ACPI: Power Resource [C1C6] (off) ACPI: Power Resource [C1C7] (off) ACPI: Power Resource [C1C8] (off) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 14 devices SCSI subsystem initialized libata version 2.20 loaded. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:00: iomem range 0x100000-0x1fffffff could not be reserved pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved pnp: 00:0c: ioport range 0x530-0x537 has been reserved pnp: 00:0c: ioport range 0x800-0x87f has been reserved pnp: 00:0c: ioport range 0x1000-0x103f has been reserved pnp: 00:0c: ioport range 0x1100-0x110f has been reserved pnp: 00:0c: iomem range 0xfff80000-0xffffffff has been reserved pnp: 00:0d: iomem range 0xd1800-0xd3fff has been reserved ieee1394: Initialized config rom entry `ip1394' Time: tsc clocksource has been installed. PCI: Bridge: 0000:00:01.0 IO window: 2000-2fff MEM window: 40000000-410fffff PREFETCH window: 38000000-380fffff PCI: Bus 2, cardbus bridge: 0000:00:04.0 IO window: 00001400-000014ff IO window: 00001800-000018ff PREFETCH window: 30000000-33ffffff MEM window: 34000000-37ffffff ACPI: PCI Interrupt Link [C090] enabled at IRQ 11 PCI: setting IRQ 11 as level-triggered ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [C090] -> GSI 11 (level, low) -> IRQ 11 NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 16384 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) NTFS driver 2.1.28 [Flags: R/W]. JFS: nTxBlock = 3986, nTxLock = 31893 SGI XFS with ACLs, security attributes, large block numbers, no debug enabled SGI XFS Quota Management subsystem OCFS2 1.3.3 OCFS2 Node Manager 1.3.3 OCFS2 DLM 1.3.3 OCFS2 DLMFS 1.3.3 OCFS2 User DLM kernel interface loaded GFS2 (built Jun 19 2007 15:21:53) installed io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Limiting direct PCI/PCI transfers. pci_hotplug: PCI Hot Plug PCI Core version: 0.5 vesafb: framebuffer at 0x40000000, mapped to 0xe0a80000, using 1536k, total 8128k vesafb: mode is 1024x768x8, linelength=1024, pages=9 vesafb: protected mode interface info at c000:5064 vesafb: pmi: set display start = c00c50bc, set palette = c00c5116 vesafb: pmi: ports = 2085 201f 20b4 20b8 2018 2014 20c0 20c3 20c1 vesafb: scrolling: redraw vesafb: Pseudocolor: size=6:6:6:6, shift=0:0:0:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled Switched to high resolution mode on CPU 0 serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ACPI: PCI Interrupt Link [C092] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:09.1[A] -> Link [C092] -> GSI 11 (level, low) -> IRQ 11 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Compaq SMART2 Driver (v 2.6.0) HP CISS Driver (v 3.6.14) input: Macintosh mouse button emulation as /class/input/input0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PIIX4: IDE controller at PCI slot 0000:00:07.1 PIIX4: chipset revision 1 PIIX4: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x3460-0x3467, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x3468-0x346f, BIOS settings: hdc:DMA, hdd:pio Probing IDE interface ide0... hda: IC25N020ATCS04-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 Probing IDE interface ide1... hdc: Compaq CRN-8241B, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 128KiB hda: 39070080 sectors (20003 MB) w/1768KiB Cache, CHS=38760/16/63, UDMA(33) hda: cache flushes not supported hda: hda1 hda2 < hda5 > hdc: ATAPI 24X CD-ROM drive, 128kB Cache, DMA Uniform CD-ROM driver Revision: 3.20 ide-floppy driver 0.99.newide Loading iSCSI transport class v2.0-724. iscsi: registered transport (tcp) Loading Adaptec I2O RAID: Version 2.4 Build 5go Detecting Adaptec I2O RAID controllers... Adaptec aacraid driver (1.1-5[2423]-mh3) aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded scsi: Detection failed (no card) sym53c416.c: Version 1.0.0-ac qlogicfas: no cards were found, please specify I/O address and IRQ using iobase= and irq= options<6>QLogic Fibre Channel HBA Driver iscsi: registered transport (qla4xxx) QLogic iSCSI HBA Driver Emulex LightPulse Fibre Channel SCSI driver 8.1.11 Copyright(c) 2004-2006 Emulex. All rights reserved. seagate: ST0x/TMC-8xx not detected. Failed initialization of WD-7000 SCSI card! DC390: clustering now enabled by default. If you get problems load with "disable_clustering=1" and report to maintainers megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006) megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006) megasas: 00.00.03.10-rc1 Wed Feb 14 10:14:25 PST 2007 GDT-HA: Storage RAID Controller Driver. Version: 3.05 GDT-HA: Found 0 PCI Storage RAID Controllers 3ware Storage Controller device driver for Linux v1.26.02.002. 3ware 9000 Storage Controller device driver for Linux v2.26.02.008. nsp32: loading... ipr: IBM Power RAID SCSI Device Driver version: 2.3.1 (January 23, 2007) RocketRAID 3xxx SATA Controller driver v1.0 (060426) st: Version 20070203, fixed bufsize 32768, s/g segs 256 I2O subsystem v1.325 i2o: max drivers = 8 I2O Configuration OSM v1.323 I2O Bus Adapter OSM v1.317 I2O Block Device OSM v1.325 I2O SCSI Peripheral OSM v1.316 I2O ProcFS OSM v1.316 Fusion MPT base driver 3.04.04 Copyright (c) 1999-2007 LSI Logic Corporation Fusion MPT SPI Host driver 3.04.04 Fusion MPT FC Host driver 3.04.04 Fusion MPT SAS Host driver 3.04.04 usbmon: debugfs is not available 116x: driver isp116x-hcd, 03 Nov 2005 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt Link [C093] enabled at IRQ 11 ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [C093] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:07.2: UHCI Host Controller uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:07.2: irq 11, io base 0x00003440 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected sl811: driver sl811-hcd, 19 May 2005 Initializing USB Mass Storage driver... usb 1-2: new full speed USB device using uhci_hcd and address 2 usb 1-2: configuration #1 chosen from 1 choice hub 1-2:1.0: USB hub found hub 1-2:1.0: 4 ports detected usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:C143,PNP0f0e:C144] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.0. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 raid6: int32x1 266 MB/s raid6: int32x2 278 MB/s raid6: int32x4 226 MB/s raid6: int32x8 208 MB/s raid6: mmxx1 767 MB/s raid6: mmxx2 957 MB/s raid6: sse1x1 693 MB/s raid6: sse1x2 946 MB/s raid6: using algorithm sse1x2 (946 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: automatically using best checksumming function: pIII_sse pIII_sse : 1691.000 MB/sec raid5: using function: pIII_sse (1691.000 MB/sec) md: multipath personality registered for level -4 device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Using IPI Shortcut mode md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. input: AT Translated Set 2 keyboard as /class/input/input1 kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. Freeing unused kernel memory: 344k freed eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin and others ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [C092] -> GSI 11 (level, low) -> IRQ 11 eth0: OEM i82557/i82558 10/100 Ethernet, 00:D0:59:C5:6C:4C, IRQ 11. Board assembly 980100-000, Physical connectors present: RJ45 Primary interface chip i82555 PHY #1. General self-test: passed. Serial sub-system self-test: passed. Internal registers self-test: passed. ROM checksum self-test: passed (0xdbd8681d). ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [C092] -> GSI 11 (level, low) -> IRQ 11 Linux agpgart interface v0.102 (c) Dave Jones kobject_add failed for uhci_hcd with -EEXIST, don't try to register things with the same name in the same directory. [] kobject_shadow_add+0x101/0x1a0 [] mod_sysfs_setup+0x18/0xb0 [] sys_init_module+0x1147/0x15d0 [] syscall_call+0x7/0xb [] auth_unix_lookup+0x70/0x90 ======================= i2c_core: exports duplicate symbol i2c_smbus_write_i2c_block_data (owned by kernel) agpgart: Detected an Intel 440BX Chipset. agpgart: AGP aperture is 64M @ 0x50000000 shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 Yenta: CardBus bridge found at 0000:00:04.0 [0e11:b103] Yenta: Enabling burst memory read transactions Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:04.0, mfunc 0x01001002, devctl 0x64 Yenta: ISA IRQ mask 0x04b8, PCI irq 11 Socket status: 30000010 piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device pccard: PCMCIA card inserted into slot 0 cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0x800-0x80f: clean. cs: IO port probe 0x3e0-0x4ff: clean. cs: IO port probe 0x100-0x3af: excluding 0x200-0x207 0x378-0x37f cs: IO port probe 0xa00-0xaff: clean. cs: memory probe 0xa0000000-0xa0ffffff: clean. pcmcia: registering new device pcmcia0.0 orinoco 0.15 (David Gibson , Pavel Roskin , et al) orinoco_cs 0.15 (David Gibson , Pavel Roskin , et al) eth1: Hardware identity 800c:0000:0001:0000 eth1: Station identity 001f:0006:0001:0003 eth1: Firmware determined as Intersil 1.3.6 eth1: Ad-hoc demo mode supported eth1: IEEE standard IBSS ad-hoc mode supported eth1: WEP supported, 104-bit key eth1: MAC address 00:09:5B:55:0D:D3 eth1: Station name "Prism I" eth1: ready eth1: orinoco_cs at 0.0, irq 3, io 0x0100-0x013f EXT3 FS on hda1, internal journal input: PC Speaker as /class/input/input2 input: PS/2 Synaptics TouchPad as /class/input/input3 parport: PnPBIOS parport detected. parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] lp0: using parport0 (interrupt-driven). lp0: console ready Capability LSM initialized eth1: New link status: Connected (0001) eth1: New link status: Disconnected (0002) eth1: New link status: Connected (0001) eth1: New link status: Disconnected (0002) eth1: New link status: Connected (0001) NET: Registered protocol family 10 lo: Disabled Privacy Extensions eth1: no IPv6 routers present usb 1-2.2: new full speed USB device using uhci_hcd and address 3 usb 1-2.2: configuration #1 chosen from 1 choice scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning kobject_add failed for usb_storage with -EEXIST, don't try to register things with the same name in the same directory. [] kobject_shadow_add+0x101/0x1a0 [] mod_sysfs_setup+0x18/0xb0 [] sys_init_module+0x1147/0x15d0 [] syscall_call+0x7/0xb [] auth_unix_lookup+0x70/0x90 ======================= scsi 2:0:0:0: Direct-Access CRUCIAL USB DRIVE 1.11 PQ: 0 ANSI: 1 CCS SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: Mode Sense: 23 00 00 00 sda: assuming drive cache: write through SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: Mode Sense: 23 00 00 00 sda: assuming drive cache: write through sda: sda1 sd 2:0:0:0: Attached scsi removable disk sda usb-storage: device scan complete sd 2:0:0:0: Attached scsi generic sg0 type 0 usb 1-2.2: USB disconnect, address 3 usb 1-2.2: new full speed USB device using uhci_hcd and address 4 usb 1-2.2: configuration #1 chosen from 1 choice scsi3 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 4 usb-storage: waiting for device to settle before scanning kobject_add failed for usb_storage with -EEXIST, don't try to register things with the same name in the same directory. [] kobject_shadow_add+0x101/0x1a0 [] mod_sysfs_setup+0x18/0xb0 [] sys_init_module+0x1147/0x15d0 [] syscall_call+0x7/0xb [] auth_unix_lookup+0x70/0x90 ======================= scsi 3:0:0:0: Direct-Access CRUCIAL USB DRIVE 1.11 PQ: 0 ANSI: 1 CCS SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: Mode Sense: 23 00 00 00 sda: assuming drive cache: write through SCSI device sda: 251904 512-byte hdwr sectors (129 MB) sda: Write Protect is off sda: Mode Sense: 23 00 00 00 sda: assuming drive cache: write through sda: sda1 sd 3:0:0:0: Attached scsi removable disk sda sd 3:0:0:0: Attached scsi generic sg0 type 0 usb-storage: device scan complete eth1: New link status: Disconnected (0002) eth1: New link status: Connected (0001)